Forum: Model A (1928-31)
01-14-2018, 06:19 PM
|
Replies: 32
Views: 4,329
Re: bearing insert identification help...
Hard times,
To answer your original question, call Max Hermans at H&H and ask him. As indicated by the MAX in yellow letters on the crank counter weight H&H is the builder of the engine. That plus...
|
Forum: Model A (1928-31)
11-22-2017, 02:12 PM
|
Replies: 56
Views: 7,723
Re: Noise in my new 29 a engin
Post number 10 reminded me of when I bought a new plunger and spring I had a knock as you do and found the new spring was very weak. Put an original spring in and the knock was gone. Just a thought...
|
Forum: Model A (1928-31)
10-16-2017, 07:14 PM
|
Replies: 13
Views: 2,850
Re: Why did I buy this?
John, you bought it to chase the tube threads in the rear main cap. Or to enlarge from the 5/16" tube in the 28 thru mid 30 cap.
|
Forum: Model A (1928-31)
08-20-2017, 10:05 AM
|
Replies: 8
Views: 1,386
|
Forum: Model A (1928-31)
08-10-2017, 09:42 AM
|
Replies: 14
Views: 1,764
|
Forum: Model A (1928-31)
07-22-2017, 11:13 AM
|
Replies: 25
Views: 3,602
Re: Little help here.
Could be the filler tube cap was pushed on too far causing back pressure forcing oil out the rear main.
|
Forum: Model A (1928-31)
12-14-2016, 11:31 AM
|
Replies: 14
Views: 2,326
Re: Vibration gas tank
I found my problem was the repro hood prop kit with the fold out ends. They attach to the radiator rods and the pivot bolt is loose that allows the ends to be folded out to hold the hood in the open...
|
Forum: Model A (1928-31)
11-07-2016, 12:26 PM
|
Replies: 72
Views: 9,075
Re: New clutch-drive shaft problem
If you removed the speedometer drive gear for some reason and put it back on the driveshaft reversed it will hold you back about 1 inch from the u-joint.
|
Forum: Model A (1928-31)
09-13-2016, 11:35 PM
|
Replies: 4
Views: 1,091
|
Forum: Model A (1928-31)
06-01-2016, 06:12 PM
|
Replies: 8
Views: 4,214
|
Forum: Model A (1928-31)
03-30-2016, 10:25 AM
|
Replies: 29
Views: 6,806
Re: throw out bearing
My guess is you have a sheared pin on either the fork that moves the throwout bearing or the leaver that is moved by the pedal. Grab both and see if one or the other moves on the shaft.
|
Forum: Model A (1928-31)
12-14-2015, 06:50 PM
|
Replies: 10
Views: 3,419
|
Forum: Model A (1928-31)
04-13-2015, 03:51 PM
|
Replies: 10
Views: 2,656
Re: Original vs "modern" starter drive
Mike,
I don't think this has ever been brought up on this site but the modern drives first imported from India by Snyders had the bevel or taper on the wrong side of the teeth. This will not only...
|
Forum: Model A (1928-31)
04-06-2015, 12:32 PM
|
Replies: 44
Views: 14,611
|
Forum: Model A (1928-31)
02-24-2015, 08:42 PM
|
Replies: 9
Views: 2,183
Re: Does this look right?
No it is not covered on the A but was change on the B to cover. You just need to be sure the slinger was installed with a sealer like permatex A2 or the like.
|
Forum: Model A (1928-31)
11-26-2014, 03:46 PM
|
Replies: 12
Views: 5,893
|
Forum: Model A (1928-31)
10-26-2014, 10:00 PM
|
Replies: 154
Views: 41,257
|
Forum: Model A (1928-31)
04-07-2014, 03:56 PM
|
Replies: 13
Views: 2,473
Re: wrong windshield ??
The frame you have is off a 28/29 closed cab pickup or truck with the hand wiper. You should trade it for the correct one so it can be saved for a pickup or truck being restored for blue ribbon...
|
Forum: Model A (1928-31)
01-23-2014, 03:02 PM
|
Replies: 10
Views: 1,887
Re: header drawing needed
Hi Scot,
Where are you located? I have one you can measure and see how it is made if you are close by. I am in central Oregon.
|
Forum: Model A (1928-31)
01-10-2014, 10:00 PM
|
Replies: 3
Views: 1,694
Re: 3/8"X32 tap?
Yes Steve you are Wrong. It is a 3/8 NEF thread and once retaped with a 1/8" NPT the cap is junk.
|
Forum: Model A (1928-31)
11-05-2013, 10:59 AM
|
Replies: 1
Views: 1,134
|
Forum: Model A (1928-31)
10-10-2013, 10:18 AM
|
Replies: 11
Views: 2,822
Re: Transmission Woes
Hi Jesse, If you have a B/W overdrive it may be in free wheeling. Pull the T handle to lock it out.
|
Forum: Model A (1928-31)
10-03-2013, 07:38 PM
|
Replies: 11
Views: 2,150
|
Forum: Model A (1928-31)
08-23-2013, 04:13 PM
|
Replies: 14
Views: 3,702
Re: engine knock
Sounds like the timing gear nut came loose. Take off the side inspection cover and check for movement of the gear on the cam.
|
Forum: Model A (1928-31)
06-23-2013, 10:43 PM
|
Replies: 8
Views: 2,022
|