Forum: Early V8
02-18-2020, 11:49 PM
|
Replies: 0
Views: 1,204
|
Forum: Model-A
10-13-2019, 09:20 AM
|
Replies: 0
Views: 887
1930 Roadster hinge
I'm looking for a Right lower cowl side 2 bolt door hinge for a 1930 Roadster. Thanks
|
Forum: Early V8 (1932-53)
06-22-2015, 08:55 AM
|
Replies: 51
Views: 16,954
|
Forum: Early V8
03-19-2015, 11:26 PM
|
Replies: 0
Views: 978
|
Forum: Model A (1928-31)
02-26-2015, 09:54 AM
|
Replies: 10
Views: 3,421
Re: 3M adhesive
I use it in my occupation (collision repair on late model vehicles), primarily for door skins, roof panels and small sections of quarter panels. I only use it where the manufacture uses it, and they...
|
Forum: Model A (1928-31)
12-15-2014, 10:31 PM
|
Replies: 27
Views: 14,529
|
Forum: Model A (1928-31)
12-15-2014, 10:00 AM
|
Replies: 27
Views: 14,529
Re: Firewall Patent Data plate question
It is fairly rough, about 2 3/4 in length. It does not have a star or anything else.
http://i239.photobucket.com/albums/ff65/autodave/Mobile%20Uploads/1418655041458-1506839379_zps4b3de869.jpg...
|
Forum: Model A (1928-31)
12-14-2014, 03:44 PM
|
Replies: 27
Views: 14,529
|
Forum: Model A (1928-31)
12-13-2014, 11:13 PM
|
Replies: 27
Views: 14,529
|
Forum: Model A (1928-31)
12-13-2014, 10:10 PM
|
Replies: 27
Views: 14,529
Firewall Patent Data plate question
I was reading a post on the HAMB about data plates and someone commented that there was never a serial number plate put on the body. Is this correct? I have this on my 30:...
|
Forum: Model A (1928-31)
12-09-2014, 11:07 PM
|
Replies: 196
Views: 67,249
|
Forum: Early V8
08-11-2014, 11:02 PM
|
Replies: 1
Views: 1,191
|
Forum: Early V8
08-10-2014, 03:01 PM
|
Replies: 1
Views: 1,191
Transmission Parts
Looking for 1932 bearing retainer plate (part #5099). Also 1935-36 clutch release arm (part #7511). Thanks
|
Forum: Early V8
05-24-2014, 04:58 PM
|
Replies: 0
Views: 791
1940 Trans parts
I am looking for closed drive parts, mainshaft, bearing retainer, and u-joint assembly. I have a open drive trans and I want to convert it to a closed drive trans. Thanks
|
Forum: Early V8 (1932-53)
04-23-2014, 10:01 PM
|
Replies: 6
Views: 1,492
Re: 99 Block?
Thanks, I found that thread...Got it narrowed down to 1940 Ford
|
Forum: Early V8 (1932-53)
04-23-2014, 03:00 PM
|
Replies: 6
Views: 1,492
Re: 99 Block?
Thanks, I was trying to date my block, but am having trouble coming to a conclusion.
|
Forum: Early V8 (1932-53)
04-23-2014, 02:37 PM
|
Replies: 6
Views: 1,492
99 Block?
Do all 99 blocks have a raised intake deck?
|
Forum: Model A (1928-31)
03-02-2014, 02:53 PM
|
Replies: 3
Views: 1,271
Re: No Start help
Dirty points. Thanks guy's, I am glad I have someplace to turn to help me out.
|
Forum: Model A (1928-31)
03-02-2014, 12:44 PM
|
Replies: 3
Views: 1,271
No Start help
I tried starting my 30 Roadster today and it would not fire. I searched some troubleshooting threads to check for spark. I read to remove 1 spark plug lead and place it 1/4 inch from the plug and...
|
Forum: Model A (1928-31)
02-16-2014, 12:20 PM
|
Replies: 1
Views: 1,317
Original radiator?
I was trying to figure out if I had an original radiator or a repro. It had a top fill at one time but is now pressurized. This is out of my '30.
...
|
Forum: Early V8 (1932-53)
02-10-2014, 12:15 PM
|
Replies: 3
Views: 1,031
|
Forum: Early V8 (1932-53)
02-10-2014, 10:16 AM
|
Replies: 3
Views: 1,031
'37 Banjo
Do the gaskets for the axle bells on a 37 rear end also double as shims?
|
Forum: Early V8 (1932-53)
01-31-2014, 09:55 AM
|
Replies: 5
Views: 1,450
|
Forum: Early V8 (1932-53)
01-30-2014, 01:44 PM
|
Replies: 5
Views: 1,450
Flathead Questions
I picked up my first flathead, a running 1940 221. It has new water pumps, a PowerGen alt., new carb, and a MSD electronic dist. I would like to just clean it up (gasket set, paint, etc.) and run it...
|
Forum: Model A (1928-31)
01-15-2014, 09:45 AM
|
Replies: 2
Views: 1,702
Good people out there...
Ran across these yesterday:
http://www.jalopyjournal.com/forum/showthread.php?t=857547
http://losangeles.craigslist.org/sgv/pts/4287845426.html
|