Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.05 seconds.
Search: Posts Made By: Gary in La.
Forum: Early V8 (1932-53) 09-19-2020, 07:11 PM
Replies: 13
Views: 240
Posted By Gary in La.
Re: 46 ford glovebox

I have an original 1946 "FORD PASSENGER CAR SALES HANDBOOK" which states the following. Light in glove compartment on SUPER DE LUXE only.

It does'nt seem to be listed in any other publication .
Forum: Early V8 (1932-53) 09-13-2020, 08:20 PM
Replies: 2
Views: 171
Posted By Gary in La.
Re: 60 hp oil pan what is the difference

No they are not interchangeable. '37-'39 rear seal is a slinger and the '40 is rope. The rear of the early pan has a large radius cut out and the '40 pan has a small cut out.
Forum: Early V8 (1932-53) 08-27-2020, 07:17 PM
Replies: 1
Views: 121
Posted By Gary in La.
Re: Shock link size question

1941 rear shock links are 4" long 78-18055-A. Your fronts are correct.
Forum: Early V8 (1932-53) 08-27-2020, 09:34 AM
Replies: 22
Views: 917
Posted By Gary in La.
Re: hurricane

Here in Lafayette we lucked out, sort of. We were on the edge of the cone and had numerous bands of wind and rain all night and this morning. Officially just below 60 mph. My big rain gauge was past...
Forum: Early V8 (1932-53) 08-23-2020, 08:58 PM
Replies: 18
Views: 515
Posted By Gary in La.
Re: 1947 convertible radio antenna

This style antenna was a carry over from 1941-42 for convertibles and station wagons. It was one of 3 types available. The second was a side cowl mount which is the hardest to find again specific to...
Forum: Early V8 (1932-53) 08-14-2020, 07:07 PM
Replies: 11
Views: 609
Posted By Gary in La.
Re: 1933 Dymaxion

As a short coupled airplane the Luscombe is a prime example. Having owned and flown a Luscombe 8A for several years I learned early on that a Luscombe had to be flown until the prop stopped. I never...
Forum: Early V8 (1932-53) 08-10-2020, 12:13 PM
Replies: 29
Views: 870
Posted By Gary in La.
Re: v8-60 transmission help

The v8-60 commercial trans uses the same gearset as the big brother in the regular cars. Thus it has the larger input shaft that uses the big brother clutch and throw out bearing. So it has a...
Forum: Early V8 (1932-53) 07-27-2020, 10:32 AM
Replies: 12
Views: 765
Posted By Gary in La.
Re: Carb rebuild instructions

The carb model 92 is the Holly that was used on the 1940 V8-60.
Forum: Early V8 (1932-53) 07-27-2020, 10:25 AM
Replies: 13
Views: 564
Posted By Gary in La.
Re: Push Choke and Throttle Rod (Wobbly)

Did'nt see your post til this am. Here is a picture of the clamp arrangement on my "46 convertable.
Forum: Early V8 (1932-53) 07-26-2020, 07:41 PM
Replies: 13
Views: 564
Posted By Gary in La.
Re: Push Choke and Throttle Rod (Wobbly)

I don't know of anyone now supplying those pieces. Years ago Drake did have them. The "L" you can easily make from a piece of sheet metal. The clamp may be found at an auto parts house that has a...
Forum: Early V8 (1932-53) 07-26-2020, 06:37 PM
Replies: 13
Views: 564
Posted By Gary in La.
Re: Push Choke and Throttle Rod (Wobbly)

There is supposed to be a clamp at the firewall where the rods come through. Should be a hole for a screw next to the firewall hole.
It consists of a 90 degree metal "L" bracket and a small metal...
Forum: Early V8 (1932-53) 07-15-2020, 08:57 AM
Replies: 10
Views: 535
Posted By Gary in La.
Re: Elgin road race

I saw the car at the 1988 meet also but did'nt get the ride. Talked to Roy about about the build. It was a beautiful car , very well done.
Forum: Early V8 (1932-53) 07-13-2020, 11:25 AM
Replies: 31
Views: 1,245
Posted By Gary in La.
Re: Been in hospital 4 Spinal Surgery

I had my triple by-pass 15 years ago along with 4 stents and they are all still passing inspection yearly. Great heart doctor.
Forum: Early V8 (1932-53) 07-11-2020, 07:38 PM
Replies: 8
Views: 336
Posted By Gary in La.
Re: Installing stainless trim on 46 runningboards

I never have slid them on. Usually line them up on the length of the board and slap (press) them in place. They will snap in place with out too much force. This was done on NOS running boards and NOS...
Forum: Early V8 (1932-53) 06-30-2020, 03:29 PM
Replies: 14
Views: 647
Posted By Gary in La.
Re: Emergency BrakeCable

Tim, that piece is what's left of the end of the cable housing. The housing end goes through the bracket and is held in place with one of those clips as used in various places on the brake system...
Forum: Early V8 (1932-53) 06-30-2020, 12:07 PM
Replies: 14
Views: 647
Posted By Gary in La.
Re: Emergency BrakeCable

What you see here is where they torched off the cable assy that runs from the hand brake lever to the bracket on the torque tube for the radius rods. The clevis end is still attached to the cable...
Forum: Early V8 (1932-53) 06-25-2020, 09:57 AM
Replies: 24
Views: 1,546
Posted By Gary in La.
Re: My junkyard find

They make dandy period type grinder stands. I take a scrap ford wheel and cut off the outer rim even with the center section then weld the axel housing on top of the center wheel section. I cut off...
Forum: Early V8 (1932-53) 05-18-2020, 02:03 PM
Replies: 20
Views: 1,072
Posted By Gary in La.
Re: Torque tech.

After reading that a bolt stripped threads during torquing with a torque wrench I just wanted to remind everyone that a calibrated tool may not keep its calibration forever. Having been in aircraft...
Forum: Early V8 (1932-53) 05-18-2020, 08:46 AM
Replies: 20
Views: 1,072
Posted By Gary in La.
Re: Torque tech.

When was the last time your torque wrench was calibrated? They can and do go out of calibration over time with use.
Forum: Early V8 (1932-53) 05-15-2020, 07:05 PM
Replies: 9
Views: 658
Posted By Gary in La.
Re: 1940-1948 Torque tube interchange

I measured a '41 tube at 72" in a thread dated 2/12/19.
Forum: Early V8 (1932-53) 05-15-2020, 01:29 PM
Replies: 9
Views: 658
Posted By Gary in La.
Re: 1940-1948 Torque tube interchange

I just measured a '39 tube that I have in the shop and it is 70".
Forum: Early V8 (1932-53) 04-23-2020, 01:50 PM
Replies: 68
Views: 3,523
Posted By Gary in La.
Re: oil price.

V8COOPMAN- Well Said. The majority of the public does not realize the number of other industries required to pump that oil out of the ground and the thousands of employees that are laid off when the...
Forum: Early V8 (1932-53) 04-13-2020, 07:49 PM
Replies: 12
Views: 658
Posted By Gary in La.
Re: master cylinder

You left out a most important one. In the deep south Louisiana bayous a water hose used to be called a "hosepipe" years ago.
Forum: Early V8 (1932-53) 04-12-2020, 08:36 PM
Replies: 18
Views: 5,432
Posted By Gary in La.
Re: Antique Auto Supply sold?

Sad to hear Stacy has passed. He was a good friend and my go to guy for NOS parts for many years. Very well informed about vintage parts and would gladly answer any questions. We visited at Pate...
Forum: Early V8 (1932-53) 04-05-2020, 07:58 PM
Replies: 15
Views: 939
Posted By Gary in La.
Re: Staying Home is for the Birds

Follow the wise advice and head to a reputable corvette repair facility. In 1964 I had a brand new 6 month old corvette convertable and while at a stop light when it turned green the idiot in the...
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 05:49 AM.