Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.07 seconds.
Search: Posts Made By: streetdreams
Forum: Late V8 11-15-2021, 06:30 PM
Replies: 0
Views: 517
Posted By streetdreams
1957 Ford rear end assy (2)

Have 2 complete 9 inch rears out of ‘57 Fords for sale . One from retractable, one from convertible. $300 obo each
Forum: Late V8 05-06-2021, 08:17 PM
Replies: 3
Views: 1,831
Posted By streetdreams
Forum: Late V8 01-21-2021, 09:37 AM
Replies: 8
Views: 2,593
Posted By streetdreams
Forum: Late V8 11-13-2020, 02:16 PM
Replies: 0
Views: 590
Posted By streetdreams
292 Ford forged steel truck crank

For sale one C1TE forged steel crankshaft for 292 Ford Y Block.
Measures up standard on rods and mains. Journals are very good with no scratching, etc. Polishing may clean it right up, at worst...
Forum: Late V8 (1954+) 07-13-2020, 08:14 AM
Replies: 7
Views: 1,403
Posted By streetdreams
Re: 1957 Country Sedan front brakes

does drum rotate or are shoes rubbing drum on inside keeping drum from rotating?
Forum: Late V8 06-30-2020, 09:04 AM
Replies: 3
Views: 1,631
Posted By streetdreams
Forum: Late V8 06-30-2020, 09:03 AM
Replies: 3
Views: 1,831
Posted By streetdreams
Forum: Late V8 06-30-2020, 09:03 AM
Replies: 2
Views: 1,371
Posted By streetdreams
Forum: Late V8 06-30-2020, 09:02 AM
Replies: 3
Views: 1,451
Posted By streetdreams
Forum: Late V8 06-30-2020, 09:02 AM
Replies: 8
Views: 2,593
Posted By streetdreams
Forum: Late V8 06-30-2020, 09:01 AM
Replies: 5
Views: 2,304
Posted By streetdreams
Forum: Late V8 06-30-2020, 09:01 AM
Replies: 2
Views: 1,626
Posted By streetdreams
Forum: Late V8 (1954+) 05-18-2020, 03:18 PM
Replies: 20
Views: 6,969
Posted By streetdreams
Re: y block oil pressure

"will ADD 5-15 psi..."?? Could this be a misprint? Piping oil from the main galley to the rocker shafts will actually cause a drop in pressure. "

No misprint. I always pressurize rocker...
Forum: Late V8 (1954+) 05-18-2020, 07:32 AM
Replies: 20
Views: 6,969
Posted By streetdreams
Re: y block oil pressure

pressurizing your rocker arm assemblies will add 5-15 psi depending on what condition your oiling system/bearings are in.
Forum: Late V8 (1954+) 02-25-2020, 11:09 AM
Replies: 22
Views: 8,956
Posted By streetdreams
Re: Y block Mercury engine color?

Kultulz, not a problem. Actually, was quite proud to see one of my jobs used as a reference. Not sure, but believe '56 Merc was the same goldish/greenish white as the '55 block/heads.
Forum: Late V8 (1954+) 02-24-2020, 09:33 PM
Replies: 22
Views: 8,956
Posted By streetdreams
Re: Y block Mercury engine color?

The gold, red, white, batwing(caddy) air cleaner 292 is a motor I built for raceron's '56 Vicky. The gold colored block was a close match to the original color of the '55 Merc block used. The other...
Forum: Late V8 01-22-2020, 08:31 AM
Replies: 2
Views: 1,626
Posted By streetdreams
Forum: Late V8 01-22-2020, 08:31 AM
Replies: 5
Views: 2,304
Posted By streetdreams
Forum: Late V8 01-22-2020, 08:30 AM
Replies: 8
Views: 2,593
Posted By streetdreams
Forum: Late V8 01-22-2020, 08:29 AM
Replies: 3
Views: 1,451
Posted By streetdreams
Forum: Late V8 01-22-2020, 08:29 AM
Replies: 2
Views: 1,371
Posted By streetdreams
Forum: Late V8 01-22-2020, 08:28 AM
Replies: 3
Views: 1,831
Posted By streetdreams
Forum: Late V8 11-20-2019, 08:50 PM
Replies: 3
Views: 1,831
Posted By streetdreams
Ford 292-312 tri power setup

Ford Y-Block tri power set up. Edelbrock 573 intake and 3 Ford 94 carbs. The 573 intake is the large port intake, best used with ECZ-C and ECZ-G heads.
The carbs are ECG center carb and EBU end...
Forum: Late V8 11-09-2019, 04:11 PM
Replies: 2
Views: 1,626
Posted By streetdreams
1963 Fairlane 289 HiPo exhaust manifolds

One set of factory exhaust manifolds for 289 HiPo Fairlane application. These are very early take-offs for header installation, have been on the shelf for over 50 years and the condition of them is...
Forum: Late V8 (1954+) 11-09-2019, 04:00 PM
Replies: 14
Views: 2,152
Posted By streetdreams
Re: Two barrel card spacer with pcv

if you're using a 2100 Ford 2 bbl, just about any mid to late '60s 302 or 351W has what you want
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 07:14 AM.