Forum: Model A (1928-31)
01-10-2021, 07:53 PM
|
|
Replies: 3
Views: 319
|
|
Forum: Model A (1928-31)
11-29-2020, 09:35 AM
|
|
Replies: 4
Views: 376
Re: Two tooth setting in a 28/29
The two tooth Gemmer setup for the '29 used a keyed steering wheel connection on the 43 inch shaft like the 44 inch shaft on the '30-31. The 7 tooth column had a splined steering wheel connection. A...
|
|
Forum: Model A (1928-31)
11-16-2020, 08:50 AM
|
|
Replies: 10
Views: 653
Re: KR Wilson Combination Machine Raising Block
The Model A engine bore is, if memory serves me right, 1/8" off center from what the Model T bore was. The plate is to raise the block to make up the difference when boring the cylinders.
|
|
Forum: Model A (1928-31)
11-13-2020, 11:17 PM
|
|
Replies: 2
Views: 446
|
|
Forum: Model A (1928-31)
11-07-2020, 06:37 PM
|
|
Replies: 12
Views: 700
Re: Ford Model A engine noise
Remove the fan belt to eliminate the generator and water pump as a source. You can get closer if needed to locate the source of the noise if it persists. With no fan or belt, listening can be done...
|
|
Forum: Model A (1928-31)
10-25-2020, 05:02 PM
|
|
Replies: 21
Views: 1,488
Re: Help diagnosing engine knock
Do check the piston to head clearance. A local club member recently installed a rebuilt engine with a new high compression head and had a similar knock. It turned out that the head was incorrectly...
|
|
Forum: Model A (1928-31)
10-01-2020, 06:46 AM
|
|
Replies: 14
Views: 1,047
|
|
Forum: Model A (1928-31)
07-22-2020, 11:47 AM
|
|
Replies: 21
Views: 1,841
Re: How common a practice is this?.
Years ago when my Father had a '53 Chevrolet that turned over very slowly even after the installation of a new starter, the mechanic installed an 8 volt battery that helped a bit. Some time later...
|
|
Forum: Model A (1928-31)
07-20-2020, 07:07 AM
|
|
Replies: 24
Views: 1,312
Re: Front License Plate Hitting Radiator
Some states, like Virginia, do require 2 plates. I use a Model A rear license plate mount on a front bumper bolt to avoid placing the license in front of the radiator. Before that, I used tape on...
|
|
Forum: Model A (1928-31)
07-08-2020, 07:47 PM
|
|
Replies: 26
Views: 2,109
|
|
Forum: Model A (1928-31)
07-08-2020, 07:45 PM
|
|
Replies: 24
Views: 1,389
Re: King Pin Retaining Bolts
Sometimes a hand held pneumatic hammer will "rattle" items loose that otherwise seemed to be joined together for good. Add a bit of your own penetrating oil to the joint for luck.
...
|
|
Forum: Model A (1928-31)
07-01-2020, 07:28 AM
|
|
Replies: 11
Views: 829
|
|
Forum: Model A (1928-31)
05-09-2020, 08:54 AM
|
|
Replies: 23
Views: 1,748
Re: Steering Box LEAKS!!
Sealant on threads of bolts in bottom plate. One of mine was drilled into housing and leaking around bolt after I rebuilt. I pulled bolts and added sealant on threads. It is dry now.
The holes for...
|
|
Forum: Model A (1928-31)
05-07-2020, 09:19 AM
|
|
Replies: 10
Views: 883
Re: Rumble Seat Deck Lids 30-31
A good '30-'31 deck or rumble lid is hard to find and thus usually demand a premium price. Even the better ones found have a bit of rust.
|
|
Forum: Model A (1928-31)
04-09-2020, 02:45 PM
|
|
Replies: 28
Views: 4,026
|
|
Forum: Model A (1928-31)
04-06-2020, 09:08 PM
|
|
Replies: 14
Views: 804
Re: Electrical Fuel Pump Wiring??
One option for a fuel pump safety switch can be found here:
https://www.revolutionelectronics.com/Products/Fuel_Pump.html
The site does list a 6 volt model. I do not know if positive ground is...
|
|
Forum: Model A (1928-31)
03-29-2020, 01:33 PM
|
|
Replies: 16
Views: 1,256
Re: Distributor advance problem
There is very little backlash in the cam to crankshaft gear mating. Rotating the crankshaft either way to allow the pin to fit in the recess of the cam gear is acceptable.
|
|
Forum: Model A (1928-31)
03-27-2020, 09:14 AM
|
|
Replies: 16
Views: 1,545
Re: Is My Cam Going Flat?
If you are rotating the crankshaft 180 degrees, then the camshaft is only rotating 90 degrees due to the cam/crank gear ratio. You are checking the valve lash on some point other than the heel of...
|
|
Forum: Model A (1928-31)
02-08-2020, 09:47 PM
|
|
Replies: 18
Views: 1,057
Re: Dipstick for Tremec T170 Transmission
For the SKF bearing series used on the Tremec Ford overdrive transmissions, you need a 6308 2RSNR bearing. This bearing has an inner and an outer rubber seal, thus the 2RS designation and the...
|
|
Forum: Model A (1928-31)
01-15-2020, 11:43 AM
|
|
Replies: 21
Views: 1,861
Re: steering sector
A good machine shop can make a coupling and then weld the top of of the seven tooth shaft shaft to the lower end of the two tooth shaft. Just be sure to get the correct overall length.
|
|
Forum: Model A (1928-31)
11-22-2019, 09:03 PM
|
|
Replies: 26
Views: 1,829
Re: non adjustable valves
Most of the time the valves can be adjusted in the Model A if adjustable tappets are in place by rotating the crankshaft until the adjustable tappet is at its highest point. With tappet wrenches,...
|
|
Forum: Model A (1928-31)
11-21-2019, 12:06 PM
|
|
Replies: 7
Views: 1,241
|
|
Forum: Model A (1928-31)
11-19-2019, 08:37 AM
|
|
Replies: 10
Views: 893
Re: long speedo cable
Smith and Jones Antique Auto Parts made a speedometer cable up for me several years ago. They made it to my desired length for my Model A overdrive. Contact them at: snjparts@gmail.com to see if...
|
|
Forum: Model A (1928-31)
11-10-2019, 08:22 AM
|
|
Replies: 70
Views: 3,656
|
|
Forum: Model A (1928-31)
10-14-2019, 07:52 AM
|
|
Replies: 13
Views: 1,030
Re: Hub puller question
I believe it will work on the '26-'27 Model T wire wheel hubs and on the early Model A hubs with the raised ribs.
|
