Forum: Early V8 (1932-53)
Today, 11:36 AM
|
Replies: 4
Views: 106
Re: Ford 1934 Tudor
The pillar-mounted assist straps were only provided on deluxe Tudor sedans, not on the standard versions.
|
Forum: Early V8 (1932-53)
05-03-2024, 07:34 PM
|
Replies: 17
Views: 5,868
|
Forum: Early V8 (1932-53)
05-03-2024, 12:46 AM
|
Replies: 11
Views: 353
|
Forum: Early V8 (1932-53)
04-30-2024, 01:51 PM
|
Replies: 8
Views: 399
|
Forum: Early V8 (1932-53)
04-29-2024, 09:05 PM
|
Replies: 2
Views: 242
Re: 1932 Ford Hood Alignment
Neither look to be in good original condition, but of the two, that in the second photo appears to be worn the least.
|
Forum: Early V8 (1932-53)
04-28-2024, 11:02 PM
|
Replies: 14
Views: 5,640
Re: Paint combination for 1933
If you mean the out-of-print V8 Club book, there's reason why the Club decided against a second printing.
If it was a U.S.-built '33, it came with black fenders regardless of it being a standard...
|
Forum: Early V8 (1932-53)
04-28-2024, 04:08 PM
|
Replies: 19
Views: 905
Re: Generator and Fan
Mke that '34-'36 as an original '33 V8 generator does not have a vented front bracket.
|
Forum: Early V8 (1932-53)
04-27-2024, 11:13 AM
|
Replies: 10
Views: 821
Re: 1932 firewall insulator - 4cyl
Yes, it's an early version. Note the lack of the extra toe room in front of where the clutch pedal would line up against the inside of the firewall compared to the one in your earlier photos.
|
Forum: Early V8 (1932-53)
04-22-2024, 12:08 PM
|
Replies: 2
Views: 158
|
Forum: Early V8 (1932-53)
04-22-2024, 12:04 PM
|
Replies: 4
Views: 357
Re: 32 b frame for v8
All '32 passenger car and commercial vehicle frames were the same at any point in time during the '32 model year, whether for a four-cylinder or V8 chassis. "32 frames have nothing in common with...
|
Forum: Early V8 (1932-53)
04-21-2024, 09:41 PM
|
Replies: 4
Views: 385
|
Forum: Early V8 (1932-53)
04-21-2024, 06:42 PM
|
Replies: 2
Views: 245
Re: 32 5W coupe lid hardware
Deck lid hinge pins for upper corners of the deck lids of '32 standard coupes and standard roadsters without rumble seats pus latch at bottom of photo for inner lower back panel.
|
Forum: Early V8 (1932-53)
04-21-2024, 06:30 PM
|
Replies: 31
Views: 4,186
Re: '36 Phaeton top/windshield seal
Any upholstery shop with a sewing machine could make it as it is just like windlacing (dense round sponge rubber core tightly wrapped in fabric), in this case top material, sewn together.
|
Forum: Early V8 (1932-53)
04-19-2024, 09:50 PM
|
Replies: 4
Views: 385
Re: After 1932 model b intake?
No, it is the earliest version where the large vacuum opening in the front was to provide vacuum through a pipe that was routed around the front of the engine to a vacuum-assisted clutch that never...
|
Forum: Early V8 (1932-53)
04-19-2024, 06:41 PM
|
Replies: 8
Views: 330
Re: 32 bb v8 radiator
One plus of the '32s is that the entire front end from the firewall to the hood, front fenders, radiator shells and radiators are interchangeable. There was a service-only heavy duty four-cylinder...
|
Forum: Early V8 (1932-53)
04-18-2024, 08:43 PM
|
Replies: 14
Views: 721
Re: 32 Ford PIckup Wind Noise
If the #1 floorboard side felt pieces are installed along with the webbing on the perimeters of both the #1 and #2 floor boards, the sponge rubber seals are installed around the pedals and steering...
|
Forum: Early V8 (1932-53)
04-18-2024, 05:34 AM
|
Replies: 13
Views: 937
Re: '34 Exhaust System
Pete,
That's a post-production 1932 V8 service inlet pipe and muffler assembly which incorporates the same muffler as the '33-'34 production assembly. The '33-'34 V8 version's inlet pipe is...
|
Forum: Early V8 (1932-53)
04-17-2024, 05:30 PM
|
Replies: 13
Views: 937
Re: '34 Exhaust System
Robert,
You're right about original mufflers. That shown in the photos in #5 above is not ar original Ford muffler as it lacks the formed circumferential beads near each end as shown in the...
|
Forum: Early V8 (1932-53)
04-16-2024, 06:09 PM
|
Replies: 6
Views: 348
Re: 1934 Phaeton Top Iron Hardware
I don't recall anyone having offered a kit of custom rivets for the '33-'34 phaeton top iron. If the original rivets are a standard diameter, you can obtain stainless rivers from McMaster-Carr and...
|
Forum: Early V8 (1932-53)
04-13-2024, 01:55 PM
|
Replies: 2,249
Views: 379,500
|
Forum: Early V8 (1932-53)
04-13-2024, 09:09 AM
|
Replies: 8
Views: 540
|
Forum: Early V8 (1932-53)
04-12-2024, 08:26 PM
|
Replies: 8
Views: 540
|
Forum: Early V8 (1932-53)
04-11-2024, 04:04 PM
|
Replies: 3
Views: 326
|
Forum: Early V8 (1932-53)
04-11-2024, 09:52 AM
|
Replies: 4
Views: 367
|
Forum: Early V8 (1932-53)
04-09-2024, 06:03 PM
|
Replies: 6
Views: 681
|