Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.06 seconds.
Search: Posts Made By: flatjack9
Forum: Early V8 (1932-53) 05-13-2021, 07:33 PM
Replies: 36
Views: 743
Posted By flatjack9
Re: Flathead Oil Pan

That's not an 8BA pan. All 8BA pans had a center sump. I believe it's a 52 - 53 Merc.
Forum: Early V8 (1932-53) 05-12-2021, 04:37 PM
Replies: 20
Views: 798
Posted By flatjack9
Re: dist cap problems again

I've been running a "crab" distributor in my 39 for 25 years. Got over 60,000 miles on it and after going to the .025 plug gap to keep the cap from developing small cracks, Have never had a moisture...
Forum: Early V8 (1932-53) 05-12-2021, 04:32 PM
Replies: 13
Views: 628
Posted By flatjack9
Re: Pre 1945 Block Cams

With a proper cooling system, I wouldn't worry about cracking the block. As Tim said, they are desirable.
Forum: Early V8 (1932-53) 05-12-2021, 09:39 AM
Replies: 4
Views: 324
Posted By flatjack9
Re: High Oil Pressure

While not too high, I would switch to 10W - 30. Been running that for many years.
Forum: Early V8 (1932-53) 05-11-2021, 09:31 AM
Replies: 20
Views: 798
Posted By flatjack9
Re: dist cap problems again

It may not be related, but I had trouble with mine at first. I opened up the plug gap because it seemed like the thing to do do. WRONG. I had constant problems. Went back to .025 plug gap and haven't...
Forum: Early V8 (1932-53) 05-09-2021, 08:15 PM
Replies: 16
Views: 1,151
Posted By flatjack9
Re: Perhaps Another "Dumb" Question

The heat helps to keep the fuel atomized for better fuel distribution and makes for a better running, more efficient engine.
Forum: Early V8 (1932-53) 05-08-2021, 10:30 PM
Replies: 16
Views: 1,151
Posted By flatjack9
Re: Perhaps Another "Dumb" Question

Sorry, but personally I would not do that to my engine.
Forum: Early V8 (1932-53) 05-08-2021, 09:58 AM
Replies: 21
Views: 617
Posted By flatjack9
Re: 1948 Ford 12 volt coil issues

Need to take the measurement at the distributor. You want a coil with about 3.5 ohms resistance.
Forum: Early V8 (1932-53) 05-04-2021, 09:52 AM
Replies: 35
Views: 2,066
Posted By flatjack9
Re: Pertronix Nightmare

The pintle in the PCV must have been stuck or gone. It's supposed to limit flow at idle.
Forum: Early V8 (1932-53) 05-03-2021, 10:42 PM
Replies: 18
Views: 1,088
Posted By flatjack9
Re: 59a stroker motor?

Narrowing the lobe separation angle will actually help the lower end as the intake closes earlier.
Forum: Early V8 (1932-53) 05-03-2021, 10:32 PM
Replies: 5
Views: 413
Posted By flatjack9
Re: Eddie Meyer or Offenhauser?

I like the Edelbrock Slingshot.
Forum: Early V8 (1932-53) 05-03-2021, 02:36 PM
Replies: 17
Views: 654
Posted By flatjack9
Re: 59ab compression numbers

What coil are you using?
Forum: Early V8 (1932-53) 05-03-2021, 12:50 PM
Replies: 11
Views: 526
Posted By flatjack9
Re: Timing an 8ba

A hotter cam is always going to idle better with more advance. As long as you're not getting any detonation, you're good to go. It would be nice if someone could come up with a crab style distributor...
Forum: Early V8 (1932-53) 05-03-2021, 12:47 PM
Replies: 19
Views: 727
Posted By flatjack9
Re: intake valve seals??

Engine vacuum will draw oil up through loose guides. Don't think it's worth worrying about.
Forum: Early V8 (1932-53) 05-03-2021, 12:44 PM
Replies: 17
Views: 654
Posted By flatjack9
Re: 59ab compression numbers

Your compression is not great, but good enough that it shouldn't cause a problem running. I assume you've checked the coil and condenser, the usual suspects. If it's running bad, try pulling the...
Forum: Early V8 (1932-53) 05-02-2021, 04:25 PM
Replies: 27
Views: 974
Posted By flatjack9
Re: Offenhauser/Edelbrock heads 59AB

Can't even get any Edelbrocks now. On back order since end of last year.
Forum: Early V8 (1932-53) 05-01-2021, 06:32 PM
Replies: 8
Views: 491
Posted By flatjack9
Forum: Early V8 (1932-53) 04-27-2021, 08:35 PM
Replies: 66
Views: 3,139
Posted By flatjack9
Re: Flathead Running rich

Looks like a carb rebuild is in order.
Forum: Early V8 04-27-2021, 03:09 PM
Replies: 0
Views: 117
Posted By flatjack9
distributor adapter

Looking for the 3 bolt to 2 bolt adapter for the "crab" distributor. Jack
Forum: Early V8 (1932-53) 04-26-2021, 01:17 PM
Replies: 18
Views: 1,088
Posted By flatjack9
Re: 59a stroker motor?

As well you should be.
Forum: Early V8 (1932-53) 04-26-2021, 01:16 PM
Replies: 38
Views: 1,899
Posted By flatjack9
Re: Head Bolt continually weeping

Run clear water in the engine for a little while and they will quit leaking.
Forum: Early V8 (1932-53) 04-22-2021, 02:03 PM
Replies: 66
Views: 3,139
Posted By flatjack9
Forum: Early V8 (1932-53) 04-21-2021, 09:57 AM
Replies: 12
Views: 533
Posted By flatjack9
Re: 39 ford deluxe fan shroud

Below. Trim shroud to fit inside the wire loom.
Forum: Early V8 (1932-53) 04-20-2021, 07:53 PM
Replies: 26
Views: 1,492
Posted By flatjack9
Re: Chevy to Flathead distributor

Charlie's distributors are all I use.
Forum: Early V8 (1932-53) 04-20-2021, 12:37 PM
Replies: 66
Views: 3,139
Posted By flatjack9
Re: Flathead Running rich

I also have used the NAPA condenser.
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 01:13 AM.