The Ford Barn
FordBarn.com
The Forum
Swap
About
Register
Calendar
Members List
Search
Today's Posts
Mark Forums Read
FAQ
The Ford Barn
>
Search Forums
Search Results
User Name
Remember Me?
Password
Sponsored Links (Register now to hide all advertisements)
Showing results 1 to 9 of 9
Search took
0.00
seconds.
Search:
Posts Made By:
fritz29
Forum:
Model A (1928-31)
09-09-2022, 03:46 PM
Replies:
4
distributor cam stuck
Views:
1,061
Posted By
fritz29
distributor cam stuck
The cam is stuck on one of my distributor shafts.
Anyone have any ideas on how to free it?
Forum:
Model A (1928-31)
07-10-2022, 03:15 PM
Replies:
9
Thread on double nut tappet
Views:
1,338
Posted By
fritz29
Re: Thread on double nut tappet
While it looks bad, I think it will take a lite honing and be good to go
Never scored a cylinder trining an engine over by hand before
Forum:
Model A (1928-31)
07-10-2022, 02:19 PM
Replies:
9
Thread on double nut tappet
Views:
1,338
Posted By
fritz29
Re: Thread on double nut tappet
I might have had it right the first time and it wasn’t meant to be shift
I must have had a bad ring, because I now have a scored cylinder
It just never ends
Forum:
Model A (1928-31)
07-10-2022, 07:29 AM
Replies:
9
Thread on double nut tappet
Views:
1,338
Posted By
fritz29
Re: Thread on double nut tappet
Yes,that would have been messy.
It should have said shift
Forum:
Model A (1928-31)
07-09-2022, 08:05 PM
Replies:
9
Thread on double nut tappet
Views:
1,338
Posted By
fritz29
Re: Thread on double nut tappet
I was until I found an easier way.
Loosen the lock nut and then print get the piston positioned to the point where you measure the gap. You can then tap the adjust or on the tappet until you get...
Forum:
Model A (1928-31)
07-08-2022, 04:59 PM
Replies:
9
Thread on double nut tappet
Views:
1,338
Posted By
fritz29
Thread on double nut tappet
I need to adjust my valves
Anyone know what the threads per inch on a double nut tappet?
Forum:
Model A (1928-31)
03-17-2022, 08:34 AM
Replies:
19
Where did you install your switches?
Views:
2,207
Posted By
fritz29
Re: Where did you install your switches?
I know this wonÂ’t help the OP issue.
If anyone is looking for a position for a single switch, you can replace the lower driverÂ’s side dash rail bolt with a switch. It was done on my 29. Tudor for...
Forum:
Model A (1928-31)
03-27-2021, 12:34 PM
Replies:
4
stuck second/high trans shaft
Views:
629
Posted By
fritz29
Re: stuck second/high trans shaft
Don't know why I didn't think of removing the first/reverse shaft. Both shafts are now out
Thanks for the help
Forum:
Model A (1928-31)
03-27-2021, 11:36 AM
Replies:
4
stuck second/high trans shaft
Views:
629
Posted By
fritz29
stuck second/high trans shaft
I'm rebuilding my trans tower and the send/high shaft is stuck.
I can't move it forwards or backwards or rotate it. Anyone have any suggestions on how to remove it?
Showing results 1 to 9 of 9
Forum Jump
User Control Panel
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
General Discussion
Model T (1909-1927)
Model A (1928-31)
Early V8 (1932-53)
Late V8 (1954+)
Hot Rods & Customs
The Swap Meet
For Sale
Model-T
Model-A
Early V8
Late V8
The Jalopy Auction House
To The Editors
Questions & Suggestions
The Test Forum
The Archives
Model-T
Model-A
Early V8
Late V8
Sponsored Links (Register now to hide all advertisements)
All times are GMT -5. The time now is
12:35 AM
.