Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.05 seconds.
Search: Posts Made By: Dennis Pereira
Forum: Model A (1928-31) 05-05-2022, 05:40 PM
Replies: 3
Views: 264
Posted By Dennis Pereira
Re: 1929 Sport Coupe Body question

Bad angle on photo I think hard to tell my standard coupe lines up closer.
Forum: Model-A 04-22-2022, 04:44 PM
Replies: 0
Views: 296
Posted By Dennis Pereira
28 / 29 sedan Rear Fenders

Nice sedan rear fenders good bead and no rust damage $250 each $500 for the pair no shipping pick up in Kelsey near Placerville California.
Forum: Model-A 04-22-2022, 04:34 PM
Replies: 0
Views: 187
Posted By Dennis Pereira
1930 radiator

Radiator and shell the radiator holds water and drains nice. Pick up only near Placerville N California $350
Forum: Model A (1928-31) 04-22-2022, 04:15 PM
Replies: 14
Views: 867
Posted By Dennis Pereira
Re: 1929 Coupe sheet metal question

Attached to the top inside of outer panel
Forum: Model A (1928-31) 04-21-2022, 02:12 PM
Replies: 14
Views: 867
Posted By Dennis Pereira
Re: 1929 Coupe sheet metal question

There's an angle bracket to connect curved panel to lower body panel. Maybe that's what you see.
Forum: Model A (1928-31) 04-21-2022, 02:02 PM
Replies: 14
Views: 867
Posted By Dennis Pereira
Re: 1929 Coupe sheet metal question

There was an angle bracket to connect the curved panel to the lower outside panel maybe that's the remnant's you see ?
Forum: Model A (1928-31) 03-24-2022, 10:38 AM
Replies: 24
Views: 2,710
Posted By Dennis Pereira
Re: Is a Restoration In Your Future?

I'm 76 and my projects have been stop and go I sold a couple to finance my 29 coupe project . The 29 standard coupe project is coming together I've been working on it almost non stop last 4 months...
Forum: Model A (1928-31) 03-09-2022, 02:48 PM
Replies: 10
Views: 739
Posted By Dennis Pereira
Re: Deck lid Handle

The 28 / 29 are not the same as the 30 different latch and handle. And yes, a mismatch and repo parts are a good bet.
Forum: Model A (1928-31) 03-04-2022, 02:01 PM
Replies: 13
Views: 779
Posted By Dennis Pereira
Re: 29 Model A brakes pull to left

Adjust all four no guess work.
Forum: The Test Forum 02-27-2022, 03:43 PM
Replies: 3
Views: 243
Posted By Dennis Pereira
Forum: Model A (1928-31) 02-25-2022, 02:07 PM
Replies: 14
Views: 891
Posted By Dennis Pereira
Re: Headlamp bucket question

That's great problem solved.
Forum: Model A (1928-31) 02-24-2022, 05:04 PM
Replies: 20
Views: 1,412
Posted By Dennis Pereira
Re: Paint problem

Did you use the right catalyst?
Forum: Model A (1928-31) 02-23-2022, 06:48 PM
Replies: 7
Views: 433
Posted By Dennis Pereira
Forum: Model A (1928-31) 02-08-2022, 11:28 AM
Replies: 15
Views: 1,538
Posted By Dennis Pereira
Re: 29front fender brazed and rivits

That hole is for the spare tire bracket.
Forum: Model A (1928-31) 02-06-2022, 01:32 PM
Replies: 11
Views: 768
Posted By Dennis Pereira
Re: New Rear Wheel Well Panel Question

That's one of the reasons they rotted along the bottom the fold trapped dirt and moisture. If I remember correctly there was a couple of spot welds.
Forum: Model A (1928-31) 02-06-2022, 11:50 AM
Replies: 11
Views: 768
Posted By Dennis Pereira
Re: New Rear Wheel Well Panel Question

Folded and crimped is the way I did it on the bottom edge. I left tabs on top of the repair panel drilled to slip over the fender bolts to hold while welded. Photo of photos so not real clear last...
Forum: Model A (1928-31) 02-03-2022, 05:19 PM
Replies: 17
Views: 892
Posted By Dennis Pereira
Re: New member Hello

Welcome and nice Truck I hunt arrowheads also.
Forum: Model A (1928-31) 12-22-2021, 11:14 AM
Replies: 5
Views: 580
Posted By Dennis Pereira
Re: plating finishes: interior handles

The brushed finish has small lines/ scratches? like you see with stainless on facets .
Forum: Model A (1928-31) 12-16-2021, 05:30 PM
Replies: 73
Views: 6,296
Posted By Dennis Pereira
Re: Your biggest Model-A mistake of the year?

My biggest mistake last week was climbing into the trunk area to drill a hole. One was way off on where the curved panel attaches, so I removed the panel. to get a good angle and I climbed in. The...
Forum: Model A (1928-31) 12-13-2021, 05:20 PM
Replies: 3
Views: 723
Posted By Dennis Pereira
Re: Ford A brakes

There's some recent post on this very subject. Search this thread function top of page.
Forum: Model A (1928-31) 12-12-2021, 05:49 PM
Replies: 6
Views: 674
Posted By Dennis Pereira
Re: Trunk lid support arm

No way WD 40 would loosen that up it was covered in powder coating not even a crack. The powder coating was smoking before it came loose it's a reproduction part, so nothing harmed. I tried PB...
Forum: Model A (1928-31) 12-09-2021, 01:10 PM
Replies: 6
Views: 674
Posted By Dennis Pereira
Re: Trunk lid support arm

Thanks time for the torch to melt the powder coat.
Forum: Model A (1928-31) 12-09-2021, 12:36 PM
Replies: 6
Views: 674
Posted By Dennis Pereira
Trunk lid support arm

My question! is this supposed to pivot? where I'm pointing this part is powder coated, I think and solid.
Forum: Model A (1928-31) 12-07-2021, 07:16 PM
Replies: 35
Views: 2,210
Posted By Dennis Pereira
Re: Is it possible to date my 28CCPU?

No need to be disappointed nice old truck.
Forum: Model A (1928-31) 12-07-2021, 06:53 PM
Replies: 8
Views: 712
Posted By Dennis Pereira
Re: E brake drags

The driver's side is dragging on my all-new parts brake job if it was running, I think a short drive might help.
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 04:47 AM.