Forum: Model A (1928-31)
04-15-2024, 12:26 AM
|
Replies: 18
Views: 1,646
|
Forum: Early V8 (1932-53)
04-12-2024, 02:43 AM
|
Replies: 7
Views: 426
Re: Oil Pressure Sender... 6v & 12v
Senders work on resistance, so 12v or 6v doesn't matter. But the gauge and sender resistance must match (aftermarket vs factory). You can make your stock gauges work with a different engine if...
|
Forum: Early V8 (1932-53)
04-12-2024, 01:25 AM
|
Replies: 13
Views: 1,092
Re: muffler
1.75" pipe and short (around 16" or less) glass packs (or Porters).
|
Forum: Model A (1928-31)
04-12-2024, 12:58 AM
|
Replies: 8
Views: 820
Re: So Cal radiator repair shop
Also another down here in Orange County. Bob has done a few radiators for me.
Garry's Radiator Service
225 W Truslow Ave # B
Fullerton, CA 92832
(714) 526-3327
|
Forum: Model A (1928-31)
04-12-2024, 12:50 AM
|
Replies: 18
Views: 1,646
|
Forum: Model A (1928-31)
01-24-2024, 01:50 AM
|
Replies: 9
Views: 1,533
|
Forum: Model A (1928-31)
01-24-2024, 01:18 AM
|
Replies: 31
Views: 2,102
Re: Do rivet nuts work?
Seat Bolt should be very secure especially in a hot rod. I would go with flat bar stock like you're talking about, attach that to both ends of the body rail frame, drill and tap for truss head...
|
Forum: Model-A
01-13-2024, 03:37 AM
|
Replies: 12
Views: 3,260
Re: 1928 Tudor parts
I have everything on my list above EXCEPT a seat bar (pictured in the post above). I need at least one but will take 2 if you have them.
Need the seat bar ONLY, can't edit the older posts.
...
|
Forum: Early V8
01-06-2024, 07:27 PM
|
Replies: 0
Views: 176
1940 car/pickup park light bulb terminal
Looking for the bulb housing with the spring on the outside and inside intact for a 1940 car/pickup or 1941 pickup. It's the one that twists into the top of the bucket to light up the park lens. I...
|
Forum: Early V8 (1932-53)
12-01-2023, 10:00 PM
|
Replies: 5
Views: 657
|
Forum: Early V8 (1932-53)
11-27-2023, 01:55 AM
|
Replies: 5
Views: 657
1941 Ford P/U question
Dumb question time, the air deflectors on a '41 p/u (the ones to direct air into the radiator). Do the side ones bolt on the inside of the grille or in between the fender and the grille?
...
|
Forum: Model-A
11-18-2023, 12:59 AM
|
Replies: 12
Views: 3,260
Re: 1928 Tudor parts
Bump for a seat bar.
https://www.fordbarn.com/forum/attachment.php?attachmentid=503791&d=1669013669
|
Forum: Model-A
09-15-2023, 08:18 PM
|
Replies: 12
Views: 3,260
|
Forum: Early V8 (1932-53)
09-05-2023, 11:38 PM
|
Replies: 18
Views: 1,415
|
Forum: Model A (1928-31)
09-05-2023, 11:07 PM
|
Replies: 3
Views: 687
|
Forum: Early V8 (1932-53)
08-22-2023, 11:50 PM
|
Replies: 10
Views: 875
Re: tire balancing 1940 coupe
Bubble or spin or on the car balancer all work great if done properly. Only thing I can add would be to "static" balance it, so all the weights are of the inside of the wheel.
|
Forum: Model-A
08-18-2023, 02:46 PM
|
Replies: 12
Views: 3,260
|
Forum: Early V8 (1932-53)
08-14-2023, 02:02 PM
|
Replies: 15
Views: 1,651
Re: Hidden USB Charger
I bought a couple of chargers from a marine parts place and made a bracket under the dash.
https://www.jalopyjournal.com/forum/attachments/power-outlet-2-jpg.4023469/
|
Forum: Model-A
07-27-2023, 12:50 AM
|
Replies: 12
Views: 3,260
|
Forum: Model-A
05-23-2023, 12:33 AM
|
Replies: 12
Views: 3,260
|
Forum: Model A (1928-31)
05-06-2023, 07:27 PM
|
Replies: 17
Views: 3,325
|
Forum: Early V8 (1932-53)
03-05-2023, 06:28 PM
|
Replies: 17
Views: 2,777
|
Forum: Early V8 (1932-53)
02-26-2023, 04:58 AM
|
Replies: 12
Views: 903
Re: tube shocks
I used an old clamp on kit in the rear. The KYBs went to my old '54 panel as they were too stiff for the '47. I know the angle is steep, but the exhaust is in the way.
|
Forum: Early V8 (1932-53)
02-26-2023, 04:53 AM
|
Replies: 12
Views: 903
Re: tube shocks
Did my '47 through the axle like a '48, go slow and use lots of cutting oil. I've seen the kits to add it on the perch pin, but I've also seen a few with broken off ears.
|
Forum: Model A (1928-31)
02-26-2023, 04:42 AM
|
Replies: 17
Views: 3,325
|