Forum: Model-A
10-31-2015, 11:50 PM
|
Replies: 2
Views: 1,003
|
Forum: Model-A
10-17-2015, 05:47 PM
|
Replies: 2
Views: 1,003
|
Forum: Model-A
10-13-2015, 04:02 PM
|
Replies: 2
Views: 1,003
Model B distributor
Here is a Model B distributor complete with cap and wires. Missing the rotor, don't know where it went. I bought this several years ago from a fella off the HAMB. He said it was rebuilt. I ran it...
|
Forum: Model-A
07-14-2015, 01:19 PM
|
Replies: 1
Views: 1,847
|
Forum: Model-A
06-25-2015, 09:33 PM
|
Replies: 1
Views: 1,847
|
Forum: Model A (1928-31)
04-06-2014, 06:30 PM
|
Replies: 28
Views: 13,572
|
Forum: Model A (1928-31)
04-02-2014, 11:22 PM
|
Replies: 21
Views: 6,263
Re: Oil Pressure Gauge
That is what I've done. I watch it when starting after it has sat awhile. Just to make sure.
|
Forum: Model A (1928-31)
01-22-2014, 04:13 PM
|
Replies: 12
Views: 3,011
Re: Wiper Motor
You may need a new arm and blade.
http://www.speedwaymotors.com/Black-12-Volt-Electric-Wiper,2999.html
...
|
Forum: Model A (1928-31)
11-10-2013, 09:39 AM
|
Replies: 14
Views: 3,329
Re: Drive Shaft Angle Question
With an open driveline you can adjust the angle of the ujoint at the rear by rotating the housing on the spring mount before welding them up. On a closed driveline the only way to change the angle...
|
Forum: Model A (1928-31)
11-01-2013, 01:54 AM
|
Replies: 16
Views: 3,192
|
Forum: Model A (1928-31)
10-02-2013, 12:10 PM
|
Replies: 19
Views: 4,282
Re: Pan Gasket / Milage
yes, it might have even been cheaper than $12, I can't remember now. I was shocked that they could get it. It was in Portland so I had to wait a day. I replaced it last month. A Felpro cork set with...
|
Forum: Model A (1928-31)
10-01-2013, 10:36 PM
|
Replies: 19
Views: 4,282
|
Forum: Model A (1928-31)
09-23-2013, 12:44 PM
|
Replies: 11
Views: 2,366
|
Forum: Model A (1928-31)
09-17-2013, 03:47 PM
|
Replies: 10
Views: 3,056
Re: Another Model A on Shorpy...
http://i81.photobucket.com/albums/j240/aj1374/SHORPY_8c30447upreview_zpsfc058ad6.jpg (http://s81.photobucket.com/user/aj1374/media/SHORPY_8c30447upreview_zpsfc058ad6.jpg.html)
|
Forum: Model A (1928-31)
09-17-2013, 12:53 PM
|
Replies: 11
Views: 3,114
|
Forum: Early V8 (1932-53)
07-21-2013, 09:42 AM
|
Replies: 17
Views: 3,265
|
Forum: Model A (1928-31)
07-19-2013, 10:58 AM
|
Replies: 16
Views: 3,152
|
Forum: Early V8
06-05-2013, 12:46 AM
|
Replies: 5
Views: 2,734
|
Forum: Model A (1928-31)
05-04-2013, 10:01 PM
|
Replies: 29
Views: 19,063
|
Forum: Model A (1928-31)
04-30-2013, 06:14 PM
|
Replies: 51
Views: 14,161
|
Forum: Model A (1928-31)
04-30-2013, 04:45 PM
|
Replies: 51
Views: 14,161
Re: found a good deal on a 1929
This has to be the greatest prank in all Ford Barndom.... Here ya had is all bickering and twittering and trying to show haw smart we are :D
|
Forum: Model A (1928-31)
04-30-2013, 08:50 AM
|
Replies: 10
Views: 2,291
|
Forum: Model A (1928-31)
04-24-2013, 01:56 PM
|
Replies: 30
Views: 8,723
|
Forum: Model A (1928-31)
04-24-2013, 01:56 PM
|
Replies: 30
Views: 8,723
Re: backfiring and not much power
check to see if your timing is not too retarded and that you carb adjustments are right. Idle mix and the gas valve that is also the choke rod. Also, you probably know this but you should pull the...
|
Forum: Model A (1928-31)
04-18-2013, 03:12 PM
|
Replies: 15
Views: 2,837
Re: Air/Fuel mix, what are you running???
I have been getting crummy mileage and a rich exhaust smell. I have been playing around to run leaner. I used to run about 1/4-1/2 open on the agv. With a few tuning changes I run with the agv barely...
|