Forum: Model A (1928-31)
02-10-2021, 07:54 PM
|
Replies: 20
Views: 3,100
|
Forum: Model A (1928-31)
02-10-2021, 05:32 PM
|
Replies: 20
Views: 3,100
|
Forum: Model A (1928-31)
02-16-2019, 10:37 AM
|
Replies: 9
Views: 1,777
|
Forum: Model A (1928-31)
02-15-2019, 11:28 PM
|
Replies: 9
Views: 1,777
Brattons window felt. Please advise
I ordered a pair of 32 inch window felts , but the groove seems too wide compared to my glass thickness. Do I just narrow the felt by hand .
This is for my 30 4 door ts Drivers side back...
|
Forum: Model A (1928-31)
06-25-2017, 10:00 PM
|
Replies: 15
Views: 1,737
|
Forum: Model A (1928-31)
06-23-2017, 07:14 PM
|
Replies: 15
Views: 1,737
|
Forum: Model A (1928-31)
06-23-2017, 07:10 PM
|
Replies: 15
Views: 1,737
|
Forum: Model A (1928-31)
06-23-2017, 06:21 PM
|
Replies: 15
Views: 1,737
Wanting to check valve clearances
Do I have to remove intake / exhaust manifolds. I would rather not.
I do have adjustable lifters , it a AER MOTOR,with about 800 miles on it.
Fredski
|
Forum: Model A (1928-31)
06-20-2017, 08:46 PM
|
Replies: 107
Views: 16,261
Re: What did you do working on you Model A today
I vacuumed the bugs out of the radiator ,with the help of a tooth pick.
Then got under to see if I have any oil leaks. ,no real leaks just a small drop,
found on the floor sometime. Next cleaned...
|
Forum: Model A (1928-31)
02-20-2017, 11:51 AM
|
Replies: 36
Views: 5,768
Re: Stainless Model A
Wonder how this is my 2005 GT convertible is not made of steel which I discovered since a magnit does not stick to it?
I have had car since new no rust.
Just wondering?
|
Forum: Model A (1928-31)
07-22-2016, 10:07 PM
|
Replies: 8
Views: 1,892
|
Forum: Model A (1928-31)
07-22-2016, 02:01 PM
|
Replies: 8
Views: 1,892
|
Forum: Model A (1928-31)
07-22-2016, 12:12 PM
|
Replies: 8
Views: 1,892
|
Forum: Model A (1928-31)
07-22-2016, 09:17 AM
|
Replies: 6
Views: 1,748
Was bored today so did a compression test
AER engine with 2000 miles, 5.5 Snyder head which was recommended,
Motor was run warm for 5 minutes.cyl 1 94 lbs. cyl 2. 90. Cyl 3. 91
Cyl 4 91. This on a non balanced motor.
Anyway just...
|
Forum: Model A (1928-31)
06-07-2016, 10:46 PM
|
Replies: 10
Views: 2,924
Re: powder coated wheels
My 21inch wheels were powder coated 3years ago, and when I examined
them, the coating is everywhere perfectly. I remember this because I
waxed the wheels outside and inner areas. Finish is still...
|
Forum: Model A (1928-31)
05-29-2016, 06:11 PM
|
Replies: 7
Views: 2,338
|
Forum: Model A (1928-31)
05-16-2016, 09:19 AM
|
Replies: 14
Views: 2,960
Re: Cutout and thoughts
Wish I could say the same mine worked perfectly for about 2 months.
Put the original back on which is original to car and were fine now.
Fredski
|
Forum: Model A (1928-31)
05-05-2016, 11:05 PM
|
Replies: 52
Views: 10,598
Re: Tubes
Also have 5 tubes from macs, and going on my third year no air loss.
Did my own install and was very careful doing so.
Fred
|
Forum: Model A (1928-31)
05-02-2016, 04:25 PM
|
Replies: 17
Views: 2,775
Re: Starting noise
If your light lever is at the top ,it's very unlikely your advance lever ,is opposite
as well. Can't be.
|
Forum: Model A (1928-31)
04-20-2016, 09:02 PM
|
Replies: 24
Views: 5,250
|
Forum: Model A (1928-31)
04-20-2016, 04:42 PM
|
Replies: 37
Views: 6,977
|
Forum: Model A (1928-31)
04-13-2016, 09:32 PM
|
Replies: 24
Views: 5,644
Re: Float a motor
I found that out,it felt like I had solid mounts until I loosened it up and seemed
fine after doing so.
Fredski
|
Forum: Model A (1928-31)
04-08-2016, 10:14 PM
|
Replies: 11
Views: 2,270
|
Forum: Model A (1928-31)
04-05-2016, 09:57 AM
|
Replies: 28
Views: 5,879
Re: Radiator woes
to insure really what you are getting order direct from the manufactures.
there are 2 companies to choose from. They also have web sites and offer
different options .
I picked mine up...
|
Forum: Model A (1928-31)
04-03-2016, 11:22 AM
|
Replies: 35
Views: 6,433
Re: Timing question again! with Pic
First ever time I did engine timing I made the same mistake.
Do it as in Marcos picture. It ran like that but Like yours had some backfiring.
freski
|