Forum: Early V8 (1932-53)
Today, 08:21 AM
|
Replies: 11
Views: 254
Re: My next flathead build?
That governor is similar to others added to automotive engines used to power farm equipment or other steady rpm applications. Inside the gov unit are weights attached to a shaft,balanced by a spring,...
|
Forum: Early V8 (1932-53)
Today, 08:08 AM
|
Replies: 176
Views: 11,679
|
Forum: Early V8 (1932-53)
Yesterday, 05:43 PM
|
Replies: 176
Views: 11,679
|
Forum: Early V8 (1932-53)
Yesterday, 03:04 PM
|
Replies: 176
Views: 11,679
|
Forum: Early V8 (1932-53)
Yesterday, 09:39 AM
|
Replies: 176
Views: 11,679
Re: 276 stroker from 35 years of parts
I used the early gears in my late (8CM) Merc. Worked just great. As you proceed to install the timing cover, try it without a gasket to check camshaft end play. If it's fine (I like a minimum of...
|
Forum: Early V8 (1932-53)
Yesterday, 06:54 AM
|
Replies: 176
Views: 11,679
Re: 276 stroker from 35 years of parts
I usually drive the gear on with a sleeve and good sized hammer, and heating it to 300-400 degrees is safe. It may drop on at 400. I like to stand 'em on end on the floor to install, but in the...
|
Forum: Early V8 (1932-53)
05-03-2024, 09:34 PM
|
Replies: 21
Views: 496
|
Forum: Early V8 (1932-53)
05-03-2024, 09:31 PM
|
Replies: 176
Views: 11,679
|
Forum: Early V8 (1932-53)
05-03-2024, 01:36 PM
|
Replies: 21
Views: 496
Re: Solenoid clicking. Won't start
https://www.speedwaymotors.com/Powermaster-9507-Flathead-Ford-V8-Gear-Reduction-Starter,2404.html
This is the good Powermaster starter. The one that looks like a normal flathead starter...not...
|
Forum: Late V8 (1954+)
04-30-2024, 05:40 PM
|
Replies: 4
Views: 178
|
Forum: Early V8 (1932-53)
04-28-2024, 04:27 PM
|
Replies: 6
Views: 296
Re: 226 engine reading 80# of oil pressure
First thing I'd do is get it fully up to temp and see what it reads. If still high I'd plumb in a mechanical gauge and see what it says. I think it's very unlikely to have 80 warmed up.
|
Forum: Early V8 (1932-53)
04-27-2024, 10:13 PM
|
Replies: 58
Views: 16,367
|
Forum: Early V8 (1932-53)
04-27-2024, 10:02 PM
|
Replies: 4
Views: 351
|
Forum: Early V8 (1932-53)
04-27-2024, 10:00 PM
|
Replies: 176
Views: 11,679
Re: 276 stroker from 35 years of parts
Those margins will run just fine. I admit to having ground the diameter of a valve down to get a thicker margin, but only if the seat is low enough on the face to still be nicely placed. You're...
|
Forum: Early V8 (1932-53)
04-27-2024, 07:00 AM
|
Replies: 176
Views: 11,679
Re: 276 stroker from 35 years of parts
Heavy liquid assembly lube is much preferred over any type of grease, which can dry out and restrict oil if not run soon after assembling. As for cam lobes, most likely with the low pressures we see...
|
Forum: Early V8 (1932-53)
04-19-2024, 05:53 PM
|
Replies: 176
Views: 11,679
|
Forum: Early V8 (1932-53)
04-18-2024, 09:32 PM
|
Replies: 14
Views: 723
Re: 32 Ford PIckup Wind Noise
Ah, but Gary's talking about heading into a 40 mph wind plus the 32's speed. Wind like that's pretty common here and makes the air speed 80-100 mph in our cars. Gets pretty noisy! :D
|
Forum: Early V8 (1932-53)
04-18-2024, 05:30 PM
|
Replies: 176
Views: 11,679
Re: 276 stroker from 35 years of parts
Can you measure the lobes of your new cam to see if they are ground with any taper? I'd be interested to know, and it'll make a difference on how you proceed with lifter inspection.
|
Forum: Early V8 (1932-53)
04-17-2024, 09:14 PM
|
Replies: 72
Views: 27,116
|
Forum: Late V8 (1954+)
04-14-2024, 08:03 AM
|
Replies: 2
Views: 396
Re: Helmet Distributor Issues
I don't understand the % figures for dwell. Do you mean degrees? If so, you should be in the 30's, not nearly so high. Your points gaps must be way too low. Generally gaps in the .016 range will work...
|
Forum: Early V8 (1932-53)
04-12-2024, 01:03 PM
|
Replies: 8
Views: 640
|
Forum: Early V8 (1932-53)
04-12-2024, 07:25 AM
|
Replies: 48
Views: 2,884
Re: NOS 8RT camshaft
If it helps, my "EA" cam in the 260" Merc will go 'round a corner at 10 mph in high gear and pull right back up to road speed no problem.This is with 3.54 gears and 29" tires. Idles smooth. You're...
|
Forum: Early V8 (1932-53)
04-12-2024, 07:19 AM
|
Replies: 8
Views: 640
|
Forum: Early V8 (1932-53)
04-08-2024, 05:00 PM
|
Replies: 96
Views: 6,546
|
Forum: Early V8 (1932-53)
04-08-2024, 04:03 PM
|
Replies: 14
Views: 822
|