Forum: Early V8 (1932-53)
04-09-2024, 03:39 PM
|
|
Replies: 6
Views: 276
|
|
Forum: Early V8 (1932-53)
04-09-2024, 07:55 AM
|
|
Replies: 6
Views: 276
Re: 49 f-1 engine color
Ok thanks. think this will suffice or would the tangerine/ orangeish color be more accurate?
|
|
Forum: Early V8 (1932-53)
04-09-2024, 07:15 AM
|
|
Replies: 6
Views: 276
49 f-1 engine color
What is the correct color? Ive been told blue, red/ orange or bronze. Anyone know for sure? Thanks
|
|
Forum: Early V8 (1932-53)
02-04-2024, 12:10 PM
|
|
Replies: 28
Views: 1,422
|
|
Forum: Early V8 (1932-53)
02-03-2024, 08:57 PM
|
|
Replies: 5
Views: 429
Re: 325 gears
Shim between pinion and bearing moves it closer to axle centerline and reduces backlash
|
|
Forum: Early V8 (1932-53)
02-03-2024, 06:58 PM
|
|
Replies: 5
Views: 429
Re: 325 gears
Thatll be on monday but im sure itll be non productive
|
|
Forum: Early V8 (1932-53)
02-03-2024, 05:24 PM
|
|
Replies: 5
Views: 429
325 gears
Looking for anyone who has installed this ratio in an early rear end. Done many 354’s but not this ratio. Im no noobie when it comes to rebuilding these but this has me about ready to throw in the...
|
|
Forum: Early V8 (1932-53)
07-21-2023, 08:08 PM
|
|
Replies: 9
Views: 843
|
|
Forum: Model A (1928-31)
07-17-2023, 02:13 PM
|
|
Replies: 2
Views: 512
Clutch finger adjustment
So have to ask what is the correct measurement from back of cover to the fingers? Im reading 11/16 or 3/4 depending on the source. Ive checked some old pressure plates with new disks and usually...
|
|
Forum: Model A (1928-31)
07-03-2023, 07:00 PM
|
|
Replies: 12
Views: 1,167
|
|
Forum: Model A (1928-31)
07-03-2023, 04:43 PM
|
|
Replies: 12
Views: 1,167
|
|
Forum: Model A (1928-31)
07-03-2023, 01:13 PM
|
|
Replies: 12
Views: 1,167
|
|
Forum: Model A (1928-31)
07-03-2023, 09:07 AM
|
|
Replies: 12
Views: 1,167
Cork rear main seal opinions?
I havent found much info regarding this type seal. I dont think they are available currently. Has anyone got any feedback as to how well they work. Or dont?
|
|
Forum: Early V8 (1932-53)
06-06-2023, 01:53 PM
|
|
Replies: 37
Views: 2,730
|
|
Forum: Early V8 (1932-53)
06-06-2023, 08:59 AM
|
|
Replies: 9
Views: 725
|
|
Forum: Early V8 (1932-53)
06-06-2023, 08:38 AM
|
|
Replies: 37
Views: 2,730
Re: 8ba fuel pump rod getting stuck
FYI. I just used one of the current pump rebuild kits. The eye in the diaphragm rod was binding on the back side of the arm hook that goes in it on full extension. I found it because it would rack...
|
|
Forum: Early V8 (1932-53)
06-06-2023, 08:16 AM
|
|
Replies: 9
Views: 725
Small bore 59a ?
Can a 3.062 bore 59a be safely taken out to 3.248 for a 265 build? Inclined to think yes provided the block castings are all the
Same
|
|
Forum: Model T (1909-1927)
10-29-2022, 09:45 AM
|
|
Replies: 2
Views: 1,355
Re: KR Wilson HCCT
There is a wiring diagram and lots of info on the mtfca website. There is also a book concerning those available from there
|
|
Forum: Model A (1928-31)
10-28-2022, 06:20 PM
|
|
Replies: 3
Views: 853
|
|
Forum: Model A (1928-31)
10-28-2022, 05:46 PM
|
|
Replies: 3
Views: 853
Model a pressure plates
Ive been trying to figure out an issue with rebuilt pressure plates and correct finger height. The disk is about .365 thick. Distance from flywheel disk face to plate mounting surface is 1.135. Not...
|
|
Forum: Model A (1928-31)
08-13-2022, 09:08 AM
|
|
Replies: 17
Views: 3,167
|
|
Forum: Model A (1928-31)
08-09-2022, 05:44 PM
|
|
Replies: 9
Views: 1,507
|
|
Forum: Model A (1928-31)
08-06-2022, 08:44 AM
|
|
Replies: 27
Views: 3,448
|
|
Forum: Early V8 (1932-53)
07-20-2022, 03:10 PM
|
|
Replies: 4
Views: 773
Re: Kr Wilson Pinion Clearance Indicator
Ya pretty sure lincoln had no published specs for pinion preload or lash. They came as a set assembled to the banjo. Makes sense you would need a gauge to install and maintain factory settings
|
|
Forum: Early V8 (1932-53)
07-18-2022, 06:30 PM
|
|
Replies: 8
Views: 1,140
Re: 8ba rod differences
I get that. Asking if anyone has any info on them…canadian , japanese, edsel fords prototype ???
|
