Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 45
Search took 0.00 seconds.
Search: Posts Made By: Ben38
Forum: Early V8 (1932-53) 01-07-2021, 12:44 PM
Replies: 2
Views: 327
Posted By Ben38
Re: Sunday April 25...

I’m looking forward to when we can finally can get back to car shows. They’re going to be awesome because of all the work people have been doing while they’ve been cooped up
Forum: Early V8 (1932-53) 12-19-2020, 12:07 PM
Replies: 29
Views: 1,353
Posted By Ben38
Re: Anti freeze

When it gets below zero I use the magnetic one on my daily driver that sits outside. Just stick it on the oil pan. Works great.
The only bad part is crawling underneath to stick it on.
Forum: Early V8 (1932-53) 12-16-2020, 11:49 AM
Replies: 60
Views: 2,823
Posted By Ben38
Forum: Early V8 (1932-53) 12-04-2020, 08:54 PM
Replies: 12
Views: 677
Posted By Ben38
Re: Soldering iron

I replaced the tip, got the nuts good and tight, was a little more patient and got ‘er done.
Thanks!
Forum: Early V8 (1932-53) 12-04-2020, 05:44 PM
Replies: 12
Views: 677
Posted By Ben38
Soldering iron

I need to replace the wires going to my horns and horn relay but my Weller gun doesn’t have enough wattage to melt the old solder joints. What wattage irons do you guys use for these joints?
Thanks
Forum: Early V8 (1932-53) 10-24-2020, 08:58 AM
Replies: 3
Views: 280
Posted By Ben38
Re: 32 Build Pt16: Axle. 59 Flatty Pt10: Liners. Plus Classics at Gaydon!

Thanks Mart. I enjoyed walking through the car show with you.
Forum: Model A (1928-31) 10-17-2020, 11:03 AM
Replies: 16
Views: 1,299
Posted By Ben38
Forum: Early V8 (1932-53) 09-12-2020, 08:41 AM
Replies: 64
Views: 3,761
Posted By Ben38
Forum: Early V8 (1932-53) 07-19-2020, 12:09 PM
Replies: 9
Views: 689
Posted By Ben38
Re: WorryWart

How long did you let them run?
Forum: Early V8 (1932-53) 01-18-2020, 11:58 AM
Replies: 61
Views: 4,175
Posted By Ben38
Re: How rare is a 39 Mercury?

Beautiful car! Thanks for posting the picture
Forum: Early V8 (1932-53) 10-22-2019, 12:19 PM
Replies: 58
Views: 3,410
Posted By Ben38
Re: Top three Ford Products, '32 - '53

I agree, but I'm a little crazy about '38 standards. LOL
Forum: Early V8 (1932-53) 10-22-2019, 12:14 PM
Replies: 2
Views: 515
Posted By Ben38
Re: Install fuel line

I have the same questions since I'll be installing a new gas line on my '38 standard soon.

Thanks for the link, that's very helpfull.

But I was wondering the same thing - do you start at the...
Forum: Early V8 (1932-53) 08-08-2019, 11:03 PM
Replies: 347
Views: 36,196
Posted By Ben38
Re: Interest in new restoration project thread?

I’m very interested too.
Thanks Mike
Forum: Early V8 (1932-53) 05-04-2019, 08:25 AM
Replies: 35
Views: 3,594
Posted By Ben38
Forum: Early V8 (1932-53) 04-14-2019, 12:26 PM
Replies: 29
Views: 2,149
Posted By Ben38
Forum: Early V8 (1932-53) 03-25-2019, 12:09 PM
Replies: 196
Views: 34,092
Posted By Ben38
Re: 1936 Truck restoration

Looking Good!!!
Forum: Early V8 (1932-53) 08-29-2018, 11:15 AM
Replies: 56
Views: 4,859
Posted By Ben38
Re: New Guy Old Truck

That is very cool
Forum: Early V8 (1932-53) 08-13-2018, 07:15 PM
Replies: 27
Views: 2,593
Posted By Ben38
Forum: Early V8 (1932-53) 07-01-2018, 05:39 PM
Replies: 12
Views: 1,320
Posted By Ben38
Re: Lower Door Weatherstrip

Going by memory on my 38 - lift up the rubber and see if there are sheet metal screws underneath going into the rail
Forum: Early V8 (1932-53) 06-24-2018, 02:07 PM
Replies: 27
Views: 2,151
Posted By Ben38
Re: 39 new clutch: how To adjust pedal assembly

How can you tell if the disc is installed backwards?
Forum: Early V8 (1932-53) 11-24-2017, 10:01 PM
Replies: 0
Views: 357
Posted By Ben38
'38 Trunk / Deck Lid Handle Repair

Have any of you peeled the stainless steel skin off the steel base to fix dents and deep scratches? How difficult is it to do? Are there any tricks?

Also, on most of the ones you see the blue...
Forum: Early V8 (1932-53) 10-16-2017, 12:18 PM
Replies: 23
Views: 3,163
Posted By Ben38
Re: Steering wheel restoration

It was a little tricky for me to get everything smooth because the PC7 was a lot harder than the old wheel material. It turned out good though.
Forum: Early V8 (1932-53) 10-08-2017, 05:58 PM
Replies: 38
Views: 2,803
Posted By Ben38
Forum: Early V8 (1932-53) 11-23-2016, 10:58 AM
Replies: 2
Views: 667
Posted By Ben38
Re: Seats

The handle looks like a 38
Forum: Early V8 (1932-53) 10-18-2016, 12:16 PM
Replies: 22
Views: 2,996
Posted By Ben38
Re: Never know what is next

Bob, I hope you feel better soon.

My Dad is 84 and with arthritis is having more and more difficulty getting around. In spite this his favorite saying is "IGNB" (I got no bitch), with the good...
Showing results 1 to 25 of 45

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 09:22 PM.