Forum: Early V8 (1932-53)
08-15-2021, 09:56 PM
|
|
Replies: 15
Views: 1,978
Re: My 1941 Ford isn't running right
I had the same problem once, turned out the spring tension of the points was just old and tired. Causing them to float at high rpms. New points fixed the problem.
|
|
Forum: Early V8 (1932-53)
07-11-2021, 08:05 AM
|
|
Replies: 22
Views: 3,285
Re: 59ab compression numbers
Yeah, she’s running well now that I’ve fixed the fuel problem. I dare say it has more power now than when I first put it together. Wonder if it’s always been plugged a little and just continued to...
|
|
Forum: Early V8 (1932-53)
07-06-2021, 10:35 PM
|
|
Replies: 22
Views: 3,285
Re: 59ab compression numbers
After lots of troubleshooting i finally found the problem. Shutoff valve on the bottom of the tank was full of crap. Bouncing are just right would cause it to plug. Fuel pressure gauge would have...
|
|
Forum: Early V8 (1932-53)
05-04-2021, 02:58 PM
|
|
Replies: 22
Views: 3,285
Re: 59ab compression numbers
I saved my old one, it actually has ford imprinted in the casing. It tested ok? I also have another new Echlin in the box. Maybe I shouldnt have replaced both the coil and condenser at the same...
|
|
Forum: Early V8 (1932-53)
05-04-2021, 02:15 PM
|
|
Replies: 22
Views: 3,285
Re: 59ab compression numbers
Napa Coil IC7 oil filled, I believe I left the resistor in under the dash. And measured 4.5 volts at the coil. Also replaced the condenser with one from Napa. I can check voltage again and try...
|
|
Forum: Early V8 (1932-53)
05-03-2021, 01:32 PM
|
|
Replies: 22
Views: 3,285
Re: 59ab compression numbers
I've replaced coil, condenser and points. Condenser and coil tested ok with but i tried it anyways. Not that its not possible one of the new parts isnt bad. I was nervous about the compression...
|
|
Forum: Early V8 (1932-53)
05-03-2021, 11:32 AM
|
|
Replies: 22
Views: 3,285
Re: 59ab compression numbers
I took a look at your post, I think we may have different issues. But im going to keep an eye out on your thread to see how it goes. Here are my plugs, I've actually wondered if im running lean. ...
|
|
Forum: Early V8 (1932-53)
05-03-2021, 08:12 AM
|
|
Replies: 22
Views: 3,285
59ab compression numbers
Just looking for some confirmation on my thinking. From reading a bunch of threads I "think" i have a good idea on whats going on.
My last trip last fall ended up coming home on a flatbed. ...
|
|
Forum: Early V8 (1932-53)
11-11-2020, 10:14 PM
|
|
Replies: 5
Views: 2,454
Re: 46 Ford pickup gas tank
I was not able to find anyone that made replacement tanks for the 42-47 truck years. Hopefully you have better luck. What I did learn was that a lot of radiator shops boil gas tanks and seal them. ...
|
|
Forum: Early V8 (1932-53)
11-08-2020, 10:29 PM
|
|
Replies: 4
Views: 995
|
|
Forum: Early V8 (1932-53)
11-08-2020, 05:08 PM
|
|
Replies: 4
Views: 995
|
|
Forum: Early V8 (1932-53)
11-08-2020, 04:02 PM
|
|
Replies: 4
Views: 995
ECH IC7 6 volt coil and 6 volt system
So I’ve read to many posts and I’m getting confused.
Stock 6 volt system with crab distributor.
ECH ic7 6 volt coil with 1.2 ohms resistance.
Bypass the resistor under the dash?
Or is...
|
|
Forum: Early V8 (1932-53)
10-30-2020, 09:46 PM
|
|
Replies: 9
Views: 1,330
|
|
Forum: Early V8 (1932-53)
10-30-2020, 09:37 PM
|
|
Replies: 9
Views: 1,330
|
|
Forum: Early V8 (1932-53)
10-30-2020, 07:33 AM
|
|
Replies: 9
Views: 1,330
6 volt ignition parts
I'm sure everyone has their own opinion. But looking for recommendations on where to buy replacement ignition parts. 6 volt Coil, points and condenser etc.... Is it worth buying a coil with a little...
|
|
Forum: Early V8 (1932-53)
09-16-2020, 02:56 PM
|
|
Replies: 13
Views: 1,405
|
|
Forum: Early V8 (1932-53)
09-08-2020, 08:52 AM
|
|
Replies: 13
Views: 1,405
|
|
Forum: Early V8 (1932-53)
09-08-2020, 08:38 AM
|
|
Replies: 13
Views: 1,405
Re: Interior kick plates
rhino liner is a good idea, I was thinking about using 1/8 hardboard. But that would fall apart if it got wet.
|
|
Forum: Early V8 (1932-53)
09-08-2020, 08:03 AM
|
|
Replies: 13
Views: 1,405
Interior kick plates
I need to make new interior kick plates for my 42. The original stuff is almost like dense oily cardboard with some sort of vinyl layer. Just wondering what other folks have used? I think it needs...
|
|
Forum: Early V8 (1932-53)
09-04-2020, 08:00 AM
|
|
Replies: 2
Views: 506
Re: Airtex E8902
Well... answered my own question. Airtex was bought by someone else and the internals of the pump are different now. Sounds like at some point they want to switch back. He didnt sound like thats...
|
|
Forum: Early V8 (1932-53)
09-04-2020, 07:44 AM
|
|
Replies: 2
Views: 506
Airtex E8902
Recently picked up a 8902 from RockAuto, looks like an Airtex... Has a generic 8902 printed on the side of it. It is not flow thru, I can barely blow any air thru the pump in either direction. ...
|
|
Forum: Early V8 (1932-53)
08-25-2020, 11:58 AM
|
|
Replies: 10
Views: 1,403
Re: Rubber fuel line failure
This is kinda of a FYI post more than anything. I bought the hose from either mac or dennis less than 2 years ago. I'm sure I bought one that was rated for ethanol. I'm guessing thats not what came...
|
|
Forum: Early V8 (1932-53)
08-25-2020, 09:14 AM
|
|
Replies: 10
Views: 1,403
|
|
Forum: Early V8 (1932-53)
08-25-2020, 07:46 AM
|
|
Replies: 10
Views: 1,403
Rubber fuel line failure
So I've been dealing with hard starting due to having fuel drain back to the tank after a week or so. I've gotten sick of trying to chase down the issue, so i went the route of adding an Airtex 8902...
|
|
Forum: Early V8 (1932-53)
08-14-2020, 11:14 AM
|
|
Replies: 14
Views: 2,251
Re: GREAT battery charger recommendation
I got the same one a few days ago, so far its working great. I like the fact you can override the safety to charge a completely dead battery for 5 minutes before going back to normal mode.
|
