Forum: Early V8 (1932-53)
04-24-2024, 05:18 PM
|
Replies: 13
Views: 575
Re: Removing perch bolt for repair
If it's still a stock 35 spring it will be attached to the wishbone in front of the axle so it will probably have some tension on it. Use a spring spreader to hold everything in place or porta power...
|
Forum: Model A (1928-31)
04-19-2024, 08:15 AM
|
Replies: 49
Views: 2,481
|
Forum: Early V8 (1932-53)
04-16-2024, 07:28 AM
|
Replies: 50
Views: 1,842
|
Forum: Early V8 (1932-53)
04-06-2024, 07:59 AM
|
Replies: 1
Views: 252
Re: 1950 sedan ignition switch
You have to pull the switch toward you to collapse the spring that seats against the inside of the dash. Rotate until the grooves line up and release.
|
Forum: Early V8 (1932-53)
04-01-2024, 07:16 PM
|
Replies: 23
Views: 1,233
Re: Clutch Release Shaft Bushing tool
Try the hose clamp around the bushing. It works just like the piston ring compressor as you drive the bushing in. I ruined two before I tried the clamp.
|
Forum: Early V8 (1932-53)
03-26-2024, 11:48 AM
|
Replies: 23
Views: 1,233
|
Forum: Model A (1928-31)
03-25-2024, 07:58 AM
|
Replies: 15
Views: 1,094
|
Forum: Early V8 (1932-53)
03-20-2024, 07:48 AM
|
Replies: 21
Views: 1,009
|
Forum: Early V8 (1932-53)
03-19-2024, 01:19 PM
|
Replies: 23
Views: 1,347
|
Forum: Early V8 (1932-53)
03-17-2024, 08:52 AM
|
Replies: 19
Views: 868
|
Forum: Early V8 (1932-53)
03-12-2024, 08:07 AM
|
Replies: 25
Views: 1,043
|
Forum: Early V8 (1932-53)
03-12-2024, 08:02 AM
|
Replies: 2
Views: 344
|
Forum: Early V8 (1932-53)
02-27-2024, 08:49 PM
|
Replies: 17
Views: 845
|
Forum: Early V8 (1932-53)
02-27-2024, 06:28 PM
|
Replies: 17
Views: 845
Re: Wheels Rotating in Opposite Direction
I meant to see if the truck would roll to eliminate the rearend as the problem. but in looking at the shifter tower the slots are not lined up for the shifter handle side to side as in neutral. The...
|
Forum: Early V8 (1932-53)
02-27-2024, 05:37 PM
|
Replies: 17
Views: 845
Re: Wheels Rotating in Opposite Direction
The 2nd and third gear synchronizer isn't centered in the hub. Is the shift lever in neutral? Before you put the top back on put it on the ground and see if it will roll.
|
Forum: Early V8 (1932-53)
02-27-2024, 04:29 PM
|
Replies: 17
Views: 845
|
Forum: Early V8
02-11-2024, 10:21 AM
|
Replies: 2
Views: 376
|
Forum: Early V8 (1932-53)
02-02-2024, 02:13 PM
|
Replies: 5
Views: 467
Re: 34 door lock code
Terry I don't think so. I use a Curtis cutter and book and it is the same as My KR Wilson. There are only 5 different depths of teeth.
|
Forum: Early V8 (1932-53)
01-29-2024, 12:53 PM
|
Replies: 9
Views: 539
Re: Shoebox door removal help
Those hinges are held on by Phillips screws so a hand impact or cordless drill to drill them out. As a last resort a sawzall to cut the hinges.
|
Forum: Early V8 (1932-53)
01-29-2024, 08:51 AM
|
Replies: 3
Views: 559
|
Forum: Early V8
01-26-2024, 12:07 PM
|
Replies: 2
Views: 376
|
Forum: Early V8 (1932-53)
01-26-2024, 12:03 PM
|
Replies: 3
Views: 559
1936 roof fabric question
Hello everyone, I was all set to order the long grain roof fabric for my 36 3 window and noticed the company offer with heavy backing and light backing. My first reaction was order the heavy but...
|
Forum: Early V8
01-22-2024, 04:28 PM
|
Replies: 2
Views: 376
1939 Deluxe and 1940 Bob Drake runningboards
This is a new set of Bob Drake Runningboards still in the original box. I want $2000 plus shipping or will trade for the same in 1935-36. Call 859-three three nine-0230. Thank you.
|
Forum: Early V8 (1932-53)
01-21-2024, 10:25 AM
|
Replies: 15
Views: 1,123
Re: Exhaust guide seals
I have a question about the solid guides. Were they ever available through the parts department? When you look them up in the parts book it only shows the one number with the groove with a note to...
|
Forum: Early V8 (1932-53)
01-19-2024, 01:33 PM
|
Replies: 10
Views: 791
|