Forum: Model A (1928-31)
08-30-2023, 01:21 PM
|
Replies: 5
Views: 770
|
Forum: Model A (1928-31)
08-30-2023, 01:06 PM
|
Replies: 5
Views: 770
|
Forum: Model A (1928-31)
08-30-2023, 12:52 PM
|
Replies: 5
Views: 770
|
Forum: Model A (1928-31)
04-04-2023, 07:46 PM
|
Replies: 17
Views: 3,378
Re: Any shops that will straighten front axle?
I have a rod setup that I made using 1/2" all threads and 1/2" tapered lug nuts to center each rod in the bores. I've verified that it is bent. It's just the bending back process that I'm not...
|
Forum: Model A (1928-31)
04-04-2023, 05:08 PM
|
Replies: 17
Views: 3,378
Re: Any shops that will straighten front axle?
Should have mentioned that in the original post. There are no reputable shops in my area that I would trust to do this work. I've had experience with most of the heavy truck repair shops where I...
|
Forum: Model A (1928-31)
04-04-2023, 04:52 PM
|
Replies: 17
Views: 3,378
Any shops that will straighten front axle?
Does anyone know of any shops in Louisiana, east TX, or even down to the Houston area who has experience straightening a front axle? I'd even be open to shipping it if not too cost prohibitive. My...
|
Forum: Model A (1928-31)
10-21-2022, 11:29 PM
|
Replies: 6
Views: 1,299
|
Forum: Model A (1928-31)
10-16-2022, 08:23 PM
|
Replies: 6
Views: 1,299
|
Forum: Model A (1928-31)
10-16-2022, 12:23 PM
|
Replies: 6
Views: 1,299
|
Forum: Model A (1928-31)
10-16-2022, 12:02 PM
|
Replies: 12
Views: 1,988
|
Forum: Model A (1928-31)
10-14-2022, 08:34 AM
|
Replies: 12
Views: 1,988
|
Forum: Model A (1928-31)
10-14-2022, 08:30 AM
|
Replies: 12
Views: 1,988
|
Forum: Model A (1928-31)
10-13-2022, 06:50 PM
|
Replies: 12
Views: 1,988
|
Forum: Model A (1928-31)
10-13-2022, 04:49 PM
|
Replies: 12
Views: 1,988
|
Forum: Model A (1928-31)
10-13-2022, 01:15 PM
|
Replies: 12
Views: 1,988
Axle holes for front spring perch slightly worn
I'm in the process of rebuilding everything in the front suspension, steering, and front brakes and have come across something I'm not sure about. While test fitting my new parts and checking for...
|
Forum: Model A (1928-31)
09-05-2022, 11:15 AM
|
Replies: 51
Views: 10,980
|
Forum: Model A (1928-31)
08-24-2022, 08:03 PM
|
Replies: 6
Views: 900
Re: Import vs USA springs
I may just have to wait (hard for an impatient person!) for Eaton to make one. They told me their lead time would be a minimum of 4 weeks. They supposedly build from the original specs (except for...
|
Forum: Model A (1928-31)
08-24-2022, 04:56 PM
|
Replies: 6
Views: 900
Import vs USA springs
Since all the vendors, including A-Springs and Eaton Detroit Spring, are out of stock of the USA-made springs, all that's currently available are the import springs. Are there any specific problems...
|
Forum: Model A (1928-31)
08-21-2022, 12:42 AM
|
Replies: 36
Views: 4,656
|
Forum: Model A (1928-31)
08-20-2022, 02:12 PM
|
Replies: 9
Views: 1,658
Re: Is this lead in the oil pan rope seal groove?
So how would that work if I need to add sealant to the groove but also have been advised to soak the rope in oil?
I should note that it wasn't solid lead or solder before I wire wheeled it (I only...
|
Forum: Model A (1928-31)
08-19-2022, 07:22 PM
|
Replies: 9
Views: 1,658
|
Forum: Model A (1928-31)
08-19-2022, 06:51 PM
|
Replies: 9
Views: 1,658
Is this lead in the oil pan rope seal groove?
Sorry for all the questions, but I'm new to A's and trying to figure things out so I can get the oil pan put back on tomorrow (hopefully).
I was taking a wire wheel to the oil pan to clean off the...
|
Forum: Model A (1928-31)
08-19-2022, 05:11 PM
|
Replies: 36
Views: 4,656
|
Forum: Model A (1928-31)
08-19-2022, 05:09 PM
|
Replies: 1
Views: 568
normal wear on Tillotson float arm?
Is it normal for a Tillotson float arm to wear/create a dimple from the needle valve so quickly?
The carb was recently rebuilt on this Model A that I bought a few weeks ago. After getting it...
|
Forum: Model A (1928-31)
08-19-2022, 04:11 PM
|
Replies: 36
Views: 4,656
|