The Ford Barn
FordBarn.com
The Forum
Swap
About
Register
Calendar
Members List
Search
Today's Posts
Mark Forums Read
FAQ
The Ford Barn
>
Search Forums
Search Results
User Name
Remember Me?
Password
Sponsored Links (Register now to hide all advertisements)
Showing results 1 to 10 of 10
Search took
0.00
seconds.
Search:
Posts Made By:
gw
Forum:
The Test Forum
12-16-2022, 12:26 PM
Replies:
4
Test post
Views:
1,712
Posted By
gw
Test post
I need 10 posts before I can PM.
Forum:
The Test Forum
12-16-2022, 12:23 PM
Replies:
1
Need posts
Views:
1,547
Posted By
gw
Need posts
I can not PM until I have 10 posts. Hope this test post counts.
Forum:
Model A (1928-31)
11-22-2020, 07:02 AM
Replies:
9
The Ace Mechanic Again
Views:
1,913
Posted By
gw
Re: The Ace Mechanic Again
I had the same problem were the engine stalled when the lights were turned on. I had an AGM battery and the battery showed 6 volts. Had the battery load tested and found that it could not supply the...
Forum:
Model A (1928-31)
11-11-2020, 08:15 AM
Replies:
5
Head light switch question
Views:
1,090
Posted By
gw
Re: Head light switch question
I had a problem where the light switch was difficult to move and sometime locked. The problem started after I had replaced both the wiring harness and the switch with remakes. I found two problems...
Forum:
Model A (1928-31)
12-24-2019, 01:07 PM
Replies:
23
Pilot Bearing Question
Views:
4,589
Posted By
gw
Pilot Bearing Question
The pilot bearing does not fit snugly on the trans input shaft. Measuring shows that the shaft is .002 smaller than the pilot bearing. Is this a problem? If so, could a brass shim ring be used?
Forum:
Model-A
11-27-2019, 12:14 PM
Replies:
0
Ford Script Piston
Views:
556
Posted By
gw
Ford Script Piston
One .010 ford script piston in good condition and one .010 ford script piston in marginal condition.
Also have two after market .040 pistons which have non standard ring thickness. The rings...
Forum:
Model A (1928-31)
11-09-2019, 12:56 PM
Replies:
2
Camshaft rear bearing oil hole
Views:
1,389
Posted By
gw
Camshaft rear bearing oil hole
The May 1929 Ford Service Bulletin has a procedure to drill a hole to oil the rear camshaft bearing. I have a Dec 28 motor and there is no issue with rear bearing wear. Is the oil hole .... not...
Forum:
Model A (1928-31)
11-06-2019, 11:30 AM
Replies:
8
Which Valve Springs Would You Use?
Views:
2,738
Posted By
gw
Re: Which Valve Springs Would You Use?
Thanks again. I read in Les Andrews' book that when using 70# plus springs, you should not use a fiber cam gear. What is your experience?
Forum:
Model A (1928-31)
11-03-2019, 03:36 AM
Replies:
8
Which Valve Springs Would You Use?
Views:
2,738
Posted By
gw
Re: Which Valve Springs Would You Use?
Thanks for the thoughts. The concern I have about the 80# springs is the excess pressure and wear on the valve seat.
Forum:
Model A (1928-31)
10-31-2019, 09:05 PM
Replies:
8
Which Valve Springs Would You Use?
Views:
2,738
Posted By
gw
Which Valve Springs Would You Use?
I am doing a valve job and have an issue with the valve springs. Les Andrews’ book has the specifications of 2-15/16” free length with 57-64 lbs of compression at 2-1/4”. The valve seats are...
Showing results 1 to 10 of 10
Forum Jump
User Control Panel
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
General Discussion
Model T (1909-1927)
Model A (1928-31)
Early V8 (1932-53)
Late V8 (1954+)
Hot Rods & Customs
The Swap Meet
For Sale
Model-T
Model-A
Early V8
Late V8
The Jalopy Auction House
To The Editors
Questions & Suggestions
The Test Forum
The Archives
Model-T
Model-A
Early V8
Late V8
Sponsored Links (Register now to hide all advertisements)
All times are GMT -5. The time now is
06:13 AM
.