Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.09 seconds.
Search: Posts Made By: Bob C
Forum: Early V8 (1932-53) Yesterday, 10:06 PM
Replies: 7
Views: 169
Posted By Bob C
Forum: Early V8 (1932-53) Yesterday, 09:20 PM
Replies: 7
Views: 169
Posted By Bob C
Re: 8BA Left Bank/Right Bank Difference at Valves

Maybe because the left and right side valves are at different angles.
https://www.fordbarn.com/forum/attachment.php?attachmentid=473993&d=1632622406
...
Forum: Early V8 (1932-53) Yesterday, 09:15 PM
Replies: 7
Views: 169
Posted By Bob C
Re: 8BA Left Bank/Right Bank Difference at Valves

Maybe because the left and right side valves are at different angles.
Forum: Model A (1928-31) 09-24-2021, 08:30 PM
Replies: 6
Views: 231
Posted By Bob C
Forum: Early V8 (1932-53) 09-24-2021, 10:27 AM
Replies: 10
Views: 446
Posted By Bob C
Re: How the heck to I get my top down????

Nice looking car. I wonder what happened to the vacuum cylinder can
on the Columbia?
Forum: Model A (1928-31) 09-23-2021, 04:45 PM
Replies: 9
Views: 392
Posted By Bob C
Re: Drag link ends

The drag link looks correct for cars after October 1928. The tie rod end bolts
should face the rear.
Forum: Model A (1928-31) 09-22-2021, 11:03 AM
Replies: 8
Views: 336
Posted By Bob C
Re: Steering arms

The arrow shows the flat on the steering arm that should keep it from rotating.
Forum: Model A (1928-31) 09-20-2021, 11:50 AM
Replies: 10
Views: 707
Posted By Bob C
Re: So, I have apparently blown head gasket

I've also had a couple of sleeved engines with no problems. Just make sure they leave
a step at the bottom of the original bore so the sleeve can't move down.
Forum: Model A (1928-31) 09-20-2021, 11:45 AM
Replies: 13
Views: 590
Posted By Bob C
Re: Door hinge screw removal

An impact driver works good also.
Forum: Early V8 (1932-53) 09-19-2021, 04:51 PM
Replies: 5
Views: 246
Posted By Bob C
Re: NOS 6 Cylinder Exhaust Manifold ID needed please!

The Hollander Interchange shows you can use that manifold on 1947-48 H engine
and 1948-51 truck 226 engine by using intake to exhaust manifold studs from the
manifold being replaced.
Forum: Early V8 (1932-53) 09-19-2021, 04:46 PM
Replies: 18
Views: 450
Posted By Bob C
Re: 34 Ford Carburetor

If it's been sitting that long I would pull the top off the carb and see if there is
old dried out gas that looks like shellac in the bowl.
Forum: Early V8 (1932-53) 09-19-2021, 04:43 PM
Replies: 13
Views: 286
Posted By Bob C
Re: 1950 Ford Steering Wheel Alignment

When you count the turns of the steering wheel lock to lock and then go half way
back is the steering wheel centered??
Forum: Model A (1928-31) 09-19-2021, 01:56 PM
Replies: 3
Views: 249
Posted By Bob C
Re: 30 Tudor Cowl to Chassis Mounts

Are you saying the frame bracket is missing??
Forum: Model A (1928-31) 09-19-2021, 01:48 PM
Replies: 14
Views: 459
Posted By Bob C
Forum: Early V8 (1932-53) 09-19-2021, 01:38 PM
Replies: 24
Views: 495
Posted By Bob C
Re: Electrical verification 32 Ford

This is from Van Pelt's site.
Forum: Early V8 (1932-53) 09-19-2021, 11:46 AM
Replies: 24
Views: 495
Posted By Bob C
Re: Electrical verification 32 Ford

The generator should not be in the circuit if the cutout points are open.
Forum: Model A (1928-31) 09-19-2021, 10:11 AM
Replies: 6
Views: 472
Posted By Bob C
Re: Rebuilding Distributor

Sounds like the washer may be to thick.
Forum: Early V8 (1932-53) 09-19-2021, 10:06 AM
Replies: 15
Views: 416
Posted By Bob C
Re: Headlight

He's not a new guy, been a member since June 2011. Just doesn't post much.
Forum: Model A (1928-31) 09-18-2021, 09:28 PM
Replies: 15
Views: 558
Posted By Bob C
Re: 1929 Model A Pickup HELP!! No forward or Reverse Gears

If the speedometer moves then the problem is in the rear axle.
Forum: Model A (1928-31) 09-18-2021, 09:25 PM
Replies: 2
Views: 227
Posted By Bob C
Re: Roadster windshield weatherstrip

Here's a picture of Marco's Roadster.
Forum: Model A (1928-31) 09-18-2021, 09:19 PM
Replies: 15
Views: 558
Posted By Bob C
Re: 1929 Model A Pickup HELP!! No forward or Reverse Gears

When you have it in gear and the clutch out and the truck is not moving is
the speedometer moving??


Typed to slow again.
Forum: Model A (1928-31) 09-18-2021, 05:23 PM
Replies: 14
Views: 459
Posted By Bob C
Re: 1929 AA Truck flat bed puzzle .

I agree with grove truck. The bed on the one I have is 69 3/4" wide.
The picture is similar to the one I have.
Forum: Model A (1928-31) 09-17-2021, 11:45 AM
Replies: 44
Views: 2,112
Posted By Bob C
Re: Fading Interest

OK, your idea of dirt cheap and mine are way different. Good luck
in what ever you choose.
Forum: Model A (1928-31) 09-17-2021, 11:40 AM
Replies: 3
Views: 338
Posted By Bob C
Re: 1930 Model A engine

Maybe Turlock Machine, I have no experience with them.
https://www.youtube.com/watch?v=meVhdz10RRc
Forum: Early V8 (1932-53) 09-17-2021, 11:27 AM
Replies: 24
Views: 1,251
Posted By Bob C
Re: Vintage battery kill switch?

I think you are overthinking this. Just make a bracket to mount the switch on the
inner fender panel near the battery. Run a short cable from the battery to the switch
and another from the switch...
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 05:19 AM.