Forum: Model A (1928-31)
Yesterday, 05:35 PM
|
Replies: 7
Views: 387
|
Forum: Model-A
01-15-2024, 07:02 PM
|
Replies: 0
Views: 434
WTB High Compression Head
Looking to buy a high compression head . Brand not important. Aluminum or Cast Iron. Message with what you have and price. thanks
|
Forum: Model-A
07-31-2017, 09:39 PM
|
Replies: 0
Views: 913
1930 Model A Tudor
I am listing this car for a friend of mine. It is a nice driver and an older restoration. Runs and drives very smooth and looks great. Many recent upgrades to include 6 v alternator, brakes, steering...
|
Forum: Early V8
07-24-2017, 04:50 PM
|
Replies: 0
Views: 543
1953 F100 flathead and bell housing
I have a complete flathead from a low mile 1953 F100 panel truck. I have no idea of the motors condition and would assume it seized? The bell housing is attached; which was for a 3 speed on the...
|
Forum: Model A (1928-31)
07-24-2017, 12:37 PM
|
Replies: 16
Views: 2,262
|
Forum: Model-A
06-11-2017, 06:23 AM
|
Replies: 2
Views: 1,874
|
Forum: Model-A
06-02-2017, 05:29 PM
|
Replies: 2
Views: 1,874
|
Forum: Model-A
05-14-2017, 09:37 AM
|
Replies: 2
Views: 1,874
AER Touring Motor
I have an unused fully rebuilt AER touring motor. It's a full insert, counter balanced crank, larger valves with a Stipe 330 cam. It has never been removed from crate/plastic. I bought this last year...
|
Forum: Model A (1928-31)
05-05-2017, 04:27 AM
|
Replies: 94
Views: 14,609
|
Forum: Model A (1928-31)
05-04-2017, 08:42 PM
|
Replies: 94
Views: 14,609
|
Forum: Model A (1928-31)
04-25-2017, 11:13 AM
|
Replies: 28
Views: 5,918
|
Forum: Model A (1928-31)
04-25-2017, 05:24 AM
|
Replies: 28
Views: 5,918
|
Forum: Model A (1928-31)
04-19-2017, 02:59 PM
|
Replies: 28
Views: 5,918
|
Forum: Model A (1928-31)
04-17-2017, 10:32 PM
|
Replies: 4
Views: 1,445
|
Forum: Model A (1928-31)
04-17-2017, 12:39 PM
|
Replies: 4
Views: 1,445
Distributor Hold Down
I have what I believe to be a Mallory electronic distributor. Im looking for the hold down device that clamps around dist. Shaft and then sits in the head with a pin. Anyone know where I can get the...
|
Forum: Model A (1928-31)
04-07-2017, 08:44 PM
|
Replies: 21
Views: 4,583
Re: Flywheel housing question
The cracks shown by J and M are nearly identical to where my housing was cracked. Couldn't see them until magna fluxed
|
Forum: Model A (1928-31)
04-05-2017, 05:02 PM
|
Replies: 21
Views: 4,583
Re: Flywheel housing question-Update
Followed HERM's advice and was able to get it within .001 at top and both sides. The bottom is still out about .020. But I believe tranny will pull that in.
One note I wanted to mention - I would...
|
Forum: Model A (1928-31)
04-04-2017, 08:41 PM
|
Replies: 21
Views: 4,583
|
Forum: Model A (1928-31)
04-03-2017, 05:39 PM
|
Replies: 21
Views: 4,583
Flywheel housing question
I've read just about every post regarding how to align the housing . I know you should have no more than .006 between the 12, 3, and 9 o'clock positions.
Here is my million dollar question:
...
|
Forum: Model A (1928-31)
04-03-2017, 01:23 PM
|
Replies: 20
Views: 3,892
|
Forum: Model A (1928-31)
03-18-2017, 06:09 AM
|
Replies: 13
Views: 4,406
|
Forum: Model A (1928-31)
03-18-2017, 06:03 AM
|
Replies: 17
Views: 2,301
Re: Bore and piston size questions
Crosscut
Buy or borrow a bore gauge and measure every cylinder top, middle, and bottom. That will give you a clear picture. I just went through this. Turns out, the pistons were too small, bores...
|
Forum: Model A (1928-31)
03-17-2017, 06:56 PM
|
Replies: 13
Views: 4,406
Re: Burtz seal question
thank you
Hmm - it didn't leak before i took it apart. Same components just a new seal. The seal seemed to fit in there very nice. Is it supposed to hold air???
Do I have any alternatives with...
|
Forum: Model A (1928-31)
03-17-2017, 06:31 PM
|
Replies: 13
Views: 4,406
Burtz seal question
I've got a crank with a turned down slinger. It's a full insert motor so I'm also using the bronze seal which slips into the block. The directions for the one piece nitrile seal say to pressure test...
|
Forum: Model A (1928-31)
03-05-2017, 08:32 AM
|
Replies: 17
Views: 5,964
Re: Piston/Head Clearance
Yes he has those size pistons. In fact, he mentioned having sizes all the way up to .140. Yes the pins came with; they have a tapered center too. Even nicer - he's a sinch to deal with. Very helpful....
|