Forum: Model A (1928-31)
04-26-2024, 06:33 PM
|
Replies: 18
Views: 1,061
Re: Distributor wiring
What is the problem with the original set up? Also the plate spring is eliminated. Without the spring the upper plate will vibrate.
For over 60 years I have worked on many Model A’s. One of my...
|
Forum: Model A (1928-31)
04-22-2024, 12:32 PM
|
Replies: 29
Views: 1,838
|
Forum: Model A (1928-31)
03-02-2024, 07:28 AM
|
Replies: 22
Views: 1,489
Re: Wheel stud replacement
Another thing to understand when removing studs. When you cut the drum with a hole saw or the Goodson Stud Cutter the stud bolt of a properly swedge bolt will not fall out of the hub. The stud should...
|
Forum: Model A (1928-31)
03-01-2024, 10:30 PM
|
Replies: 22
Views: 1,489
Re: Wheel stud replacement
Bruce you may be right, but here is my experience. The hole in the drum is tapered. Wide at the top, narrow at the bottom. The hole saws that I am familiar with are straight. The drum thickness is...
|
Forum: Model A (1928-31)
03-01-2024, 08:21 PM
|
Replies: 22
Views: 1,489
Re: Wheel stud replacement
I think there is a some of bad information here.
Jimczeb wants to replace one stud in a hub and drum assembly. If a hole saw is used he will destroy the drum for future swedging.
No mention has...
|
Forum: Model A (1928-31)
03-01-2024, 02:52 PM
|
Replies: 22
Views: 1,489
Re: Wheel stud replacement
Your location might help solve your problem. It is not the kind of job just anyone can do without the proper tools and experience.
|
Forum: Model A (1928-31)
02-13-2024, 08:38 PM
|
Replies: 7
Views: 956
Re: New cast iron rear drums
I have ordered a couple hundred drums over the last twenty years. Mostly from Brattons, a few were from Snyders. Never a problem. Would you consider telling us where the drums came from.
|
Forum: Model A (1928-31)
12-29-2023, 12:10 PM
|
Replies: 11
Views: 827
|
Forum: Model A (1928-31)
11-18-2023, 12:59 PM
|
Replies: 35
Views: 3,017
Re: help dowshift 3rd to 2nd
Many engine builders will tell you never downshift to slow a car down. Down shifting at a high speed puts a strain on the engine. It is better to use your brakes than use the engine/transmission to...
|
Forum: Model A (1928-31)
10-12-2023, 06:51 PM
|
Replies: 24
Views: 3,017
Re: Swaging brake drum studs
Rocket1. Be careful. You are on a path to maiming yourself or a bystander. And that is before you take the hub and drum out of the press. The press must strong enough not to flex while pressing...
|
Forum: Model A (1928-31)
09-17-2023, 07:08 PM
|
Replies: 18
Views: 1,990
Re: Close Enough to Ford Maroon
We should think about this for a minute. Do we really know if the color is an original ford color? If it is original it probably faded over the years. I would go to a paint supplier or body shop and...
|
Forum: Model A (1928-31)
08-22-2023, 05:47 PM
|
Replies: 9
Views: 1,091
|
Forum: Model A (1928-31)
07-29-2023, 07:14 PM
|
Replies: 20
Views: 1,466
Re: Stumped
Easy fix. If you are on the side of the road with a clogged pencil filter.
Be careful of any dripping gas around a hot engine.
Turn off the fuel valve.
Just slightly loosen the fuel...
|
Forum: Model A (1928-31)
07-17-2023, 05:48 PM
|
Replies: 24
Views: 2,242
|
Forum: Model A (1928-31)
06-24-2023, 01:23 PM
|
Replies: 51
Views: 5,389
Re: Trailering Model A
I now have a headache. My first Model A I towed home with a chain. The farmer I bought the Model A from towed it with his 1946 Ford PU. This was in 1952. I could hardly reach the pedals when...
|
Forum: Model A (1928-31)
06-02-2023, 08:15 PM
|
Replies: 6
Views: 1,135
Re: Vin number
VIN Number legal definition. Don’t get mad at me. I am just reporting what I see. I would call it a serial number, ID number, or maybe something else, but not a VIN number
A VIN is composed of...
|
Forum: Model A (1928-31)
05-29-2023, 10:38 AM
|
Replies: 20
Views: 3,302
Re: Balancing Beads
I have been selling balance beads and installing beads for years and they will balance a tire and maybe masks some other front end problems. Trucks, Corvettes, motor cycles and Model As. Never had a...
|
Forum: Model A (1928-31)
05-27-2023, 01:47 PM
|
Replies: 14
Views: 1,646
Re: Reaming Axle Spindle to fit King Pin
Ream again. Never turn a reamer backwards. Use a good cutting oil for reaming. Make sure reamed hole and king pin are absolutely spotless. Now try it. If sill a problem call the vender. Hopefully...
|
Forum: Model A (1928-31)
05-23-2023, 03:26 PM
|
Replies: 18
Views: 2,209
Re: Correct A belt size.
I have been following this thread for a couple of days. Snyders as well as other venders have been selling fan belts for decades. Many many belts have gone out the door to satisfied customers. ...
|
Forum: Model A (1928-31)
05-14-2023, 09:10 AM
|
Replies: 11
Views: 1,278
Re: clutch/brake pedal bushings
I make all my own bushing drivers. The driver is a tad bit longer than the bushing in most cases. I clean and lubricate where the bushing is to be installed and press the bushing in. Much less...
|
Forum: Model A (1928-31)
04-24-2023, 03:17 PM
|
Replies: 20
Views: 4,228
Re: Brake drums
Synchro909 is correct is saying the drums are only part of the equation.
I have done quite a few complete brake jobs. I would not do a partial at the customers request. If a customer wants a...
|
Forum: Model A (1928-31)
03-26-2023, 07:14 AM
|
Replies: 20
Views: 4,228
Re: Brake drums
Why are Mel Gross cast iron drums better than other cast iron drums?
|
Forum: Model A (1928-31)
02-16-2023, 06:03 PM
|
Replies: 28
Views: 3,181
|
Forum: Model T (1909-1927)
02-11-2023, 02:27 PM
|
Replies: 12
Views: 2,043
|
Forum: Model T (1909-1927)
02-10-2023, 06:48 PM
|
Replies: 12
Views: 2,043
Good book for T info
A Model A friend of mine just acquired a Model T and needs a couple of books with information. Similar to the Model A red book and the judging standards. Thanks in advance.
|