Forum: Model A (1928-31)
04-04-2024, 03:15 PM
|
Replies: 0
Views: 289
|
Forum: Model A (1928-31)
04-07-2023, 03:55 PM
|
Replies: 11
Views: 1,842
Re: Dipper tray lose
Thanks for the feedback. I’m going to bite the bullet and assume that I didn’t have it correctly installed from day one.
I reinstalled te tray into the pan today, seems pretty tight, but I will be...
|
Forum: Model A (1928-31)
04-06-2023, 11:00 AM
|
Replies: 11
Views: 1,842
Dipper tray lose
After approximately 12k miles, 2 1/2 years since assembly, my engine started making rapping sounds, similar to valve train noise. Checking the valve adjustment,springs,et,not finding anything.
Went...
|
Forum: Model A (1928-31)
03-29-2023, 04:37 AM
|
Replies: 0
Views: 422
Piston Power Show, Cleveland
The Northern Ohio Model A Club (NOMAC) will have a Model A display at the show this coming weekend.
Stop in and say hello.
Our display is in the South Hall,, southeast corner.
Fri-Sunday.
|
Forum: Model A (1928-31)
10-19-2022, 04:38 PM
|
Replies: 6
Views: 1,208
Block identity
This engine is in a 29 coupe that I just recommissioned, after sitting for eight years.
The block doesn’t have any ID number on the engine pad, and has this unusual oil drain tube.
Also, has some...
|
Forum: Model A (1928-31)
09-19-2022, 01:52 PM
|
Replies: 19
Views: 2,842
Re: 6V Timing Light?
Summit Racing
#SUM-G1069-13
Uses 2 D-cell batteries
$49.99
Still have to positively locate top dead center, and make some kind of pointer.
KK
|
Forum: Model A (1928-31)
06-21-2022, 05:19 AM
|
Replies: 21
Views: 3,198
|
Forum: Model A (1928-31)
06-20-2022, 11:03 AM
|
Replies: 21
Views: 3,198
|
Forum: Model A (1928-31)
06-18-2022, 06:19 AM
|
Replies: 21
Views: 3,198
|
Forum: Model A (1928-31)
06-17-2022, 12:38 PM
|
Replies: 21
Views: 3,198
|
Forum: Model A (1928-31)
06-16-2022, 06:20 AM
|
Replies: 21
Views: 3,198
|
Forum: Model A (1928-31)
06-15-2022, 05:37 AM
|
Replies: 21
Views: 3,198
|
Forum: Model A (1928-31)
06-14-2022, 06:36 AM
|
Replies: 21
Views: 3,198
|
Forum: Model A (1928-31)
06-13-2022, 02:23 PM
|
Replies: 21
Views: 3,198
Great Racers
The “Northern Ohio Model A Club” (NOMAC) will have service and repair assistance available to entrants during your Ohio transit.
Phone 216-904-0437 only ,Sunday, June 19, thru Wednesday June 22....
|
Forum: Model A (1928-31)
04-09-2022, 06:52 AM
|
Replies: 3
Views: 837
|
Forum: Model A (1928-31)
04-09-2022, 03:41 AM
|
Replies: 3
Views: 837
Adjusting clutch fingers
Getting ready to bench adjust clutch.
Original pressure plate, original flywheel, replacement disc (measures .380”)
Reading most of the threads on this subject, as well as watching YouTube...
|
Forum: Model A (1928-31)
04-02-2022, 05:33 AM
|
Replies: 3
Views: 861
|
Forum: Model A (1928-31)
04-01-2022, 05:42 AM
|
Replies: 3
Views: 861
|
Forum: Model A (1928-31)
03-31-2022, 04:34 AM
|
Replies: 3
Views: 861
|
Forum: Model A (1928-31)
03-30-2022, 04:48 AM
|
Replies: 3
Views: 861
Piston-Power Show, Cleveland
The Northern Ohio Model A Club will be displaying 10 Model A’s at the I-X Center, Piston Power Show this weekend, April 1-3.
Stop in and say hello.
|
Forum: Model-A
07-27-2021, 05:29 AM
|
Replies: 0
Views: 775
For Sale: ‘30 Ford Steel
From 1930 Ford Coupe
Front fenders
Rear fenders
Running boards
Pans
All original Ford, great condition
Will not separate, local pickup only.
$2800
Ken
|
Forum: Model A (1928-31)
07-20-2021, 08:00 AM
|
Replies: 13
Views: 1,790
Engine color
Why was green chosen for engine color on Model A’s?
Just curious.
Thanks
Ken
|
Forum: Model A (1928-31)
06-23-2021, 07:44 AM
|
Replies: 29
Views: 4,744
Travel Breakdowns
What is your procedure used when one of the travelers cars breaks down while on tour.
How much time do you allocate to getting him/her running again when you are under a time constraint?
Just...
|
Forum: Model-A
12-22-2020, 04:00 PM
|
Replies: 0
Views: 657
Windowed engine block
Looking for an A block with obvious damage from an errant connecting rod.
For a table project.
Prefer nearby, to avoid shipping charges.
PM me, thanks.
Happy Holidays everyone!!!!!!
|
Forum: Model A (1928-31)
11-23-2020, 11:22 AM
|
Replies: 8
Views: 1,417
Re: Engine knock
Update:
All four connecting rods are twisted .003-.0045, pin not parallel to crank. When these rods were removed from the engine, excessive torque was required to loosen. Had to use a two foot...
|