Forum: Early V8 (1932-53)
11-06-2018, 05:55 AM
|
Replies: 5
Views: 1,425
|
Forum: Early V8 (1932-53)
11-05-2018, 11:15 AM
|
Replies: 5
Views: 1,425
lekage cylinderhead
the right cylinderhead has a litttle crack on top where a little bit cooling flued through leaks what is the best way to close it
|
Forum: Early V8 (1932-53)
11-03-2018, 01:47 PM
|
Replies: 12
Views: 3,491
Re: air sucking problem
thanks for the info i am going to do the test with the blow gun and the rag
i have checked al the valves the are al working so this story wil be continued
|
Forum: Early V8 (1932-53)
11-03-2018, 06:48 AM
|
Replies: 12
Views: 3,491
Re: air sucking problem
y took of the manifold and it is oke now i remove the cylinder heads and look if everything is oke there
|
Forum: Early V8 (1932-53)
11-01-2018, 11:44 AM
|
Replies: 12
Views: 3,491
|
Forum: Early V8 (1932-53)
11-01-2018, 11:43 AM
|
Replies: 12
Views: 3,491
Re: air sucking problem
I have tested the compression with a tester and i had on every cilinder aproximaly 4
so the compression is ok on every cilinder
|
Forum: Early V8 (1932-53)
11-01-2018, 07:12 AM
|
Replies: 12
Views: 3,491
air sucking problem
My 60 hp engine from my ford won't suck air trough the left hole under the carburateur the right hole sucks air but the left sucks no air what can that be
so the engine runs only on a few cilinders?
|
Forum: Early V8 (1932-53)
10-26-2018, 12:50 PM
|
Replies: 25
Views: 4,843
Re: bendex problems
i found a shop for vintage tractors 10 miles from me so and they sell them so again many thanks for the info
|
Forum: Early V8 (1932-53)
10-26-2018, 12:37 PM
|
Replies: 25
Views: 4,843
|
Forum: Early V8 (1932-53)
10-26-2018, 12:14 PM
|
Replies: 25
Views: 4,843
Re: bendex problems
yes I try it but the most of the bendex are not foor 60 hp engines
so i looked at the side from macs and there are al kind of bendex exept 60 hp
in the netherlands are not so mutch ford with 60 hp...
|
Forum: Early V8 (1932-53)
10-26-2018, 09:33 AM
|
Replies: 25
Views: 4,843
|
Forum: Early V8 (1932-53)
10-26-2018, 07:39 AM
|
Replies: 25
Views: 4,843
|
Forum: Early V8 (1932-53)
10-26-2018, 06:08 AM
|
Replies: 25
Views: 4,843
Re: bendex problems
oke i have an old type bendex on stock but it is a lot bigger then the one y have at this moment on my starter engine does that fits on the flywheel and how can i post a picture of the two so you can...
|
Forum: Early V8 (1932-53)
10-24-2018, 12:45 PM
|
Replies: 25
Views: 4,843
|
Forum: Early V8 (1932-53)
10-24-2018, 12:41 PM
|
Replies: 25
Views: 4,843
|
Forum: Early V8 (1932-53)
10-23-2018, 09:45 AM
|
Replies: 25
Views: 4,843
Re: bendex problems
when i start the engine the bendix kiks in but it jumps before out the engine fires
|
Forum: Early V8 (1932-53)
10-22-2018, 12:45 PM
|
Replies: 25
Views: 4,843
|
Forum: Early V8 (1932-53)
10-22-2018, 12:33 PM
|
Replies: 25
Views: 4,843
bendex problems
hello
my bendex jumps every time out of the flywheel when i am cranking my 1940 ford fordor
it jumps out when y push the starter button so i can't start what can be the problem then bendex is a...
|
Forum: Early V8 (1932-53)
12-29-2015, 11:42 AM
|
Replies: 13
Views: 2,118
|
Forum: Early V8 (1932-53)
12-29-2015, 11:10 AM
|
Replies: 13
Views: 2,118
Re: ford fordor 1940 v8 won't start whwn warm
The engine does not stall wen it is warm. it runs very smoothly when it is warm and it also eactrs to the gas pedal very well but when it is turned of and it stands for 10 or 15 minutes it wil not...
|
Forum: Early V8 (1932-53)
12-29-2015, 09:53 AM
|
Replies: 13
Views: 2,118
|
Forum: Early V8 (1932-53)
12-29-2015, 09:33 AM
|
Replies: 13
Views: 2,118
|