Forum: Model A (1928-31)
04-03-2022, 06:44 PM
|
Replies: 25
Views: 4,162
Re: Clutch grabs high
Thanks for the help been under my car all day finishing up my new clutch install Kevin
|
Forum: Model A (1928-31)
04-03-2022, 06:40 PM
|
Replies: 21
Views: 2,257
|
Forum: Model A (1928-31)
04-03-2022, 12:25 AM
|
Replies: 25
Views: 4,162
Re: Clutch grabs high
Order the new modern adj rod you can adjust without removing the pin I just put one on my car and was a brease to adj Kevin
|
Forum: Model A (1928-31)
04-02-2022, 06:47 PM
|
Replies: 21
Views: 2,257
|
Forum: Model A (1928-31)
03-29-2022, 12:20 PM
|
Replies: 21
Views: 2,257
|
Forum: Model A (1928-31)
03-29-2022, 12:10 PM
|
Replies: 21
Views: 2,257
|
Forum: Model A (1928-31)
03-29-2022, 12:08 PM
|
Replies: 21
Views: 2,257
|
Forum: Model A (1928-31)
03-29-2022, 12:04 PM
|
Replies: 21
Views: 2,257
|
Forum: Model A (1928-31)
03-29-2022, 11:28 AM
|
Replies: 21
Views: 2,257
|
Forum: Model A (1928-31)
03-23-2022, 07:55 PM
|
Replies: 3
Views: 770
|
Forum: Model A (1928-31)
09-09-2021, 08:28 PM
|
Replies: 3
Views: 889
need help electrical
hello all i need sme help this is not a foed question but a 1935 ply question i am working on my father in laws 35 plym i have it back togeather an has beed running great the other day i drove it and...
|
Forum: Model A (1928-31)
04-01-2021, 12:50 PM
|
Replies: 7
Views: 1,316
Re: Clutch problem on 30 CCPU
i had this happen and the arn on the clutch shaft cracked i could not see it but no clutch i foud it put new one on fixed
kevin
1930 Tudor
|
Forum: Model T (1909-1927)
03-23-2021, 03:09 PM
|
Replies: 17
Views: 2,159
|
Forum: Model T (1909-1927)
03-23-2021, 08:33 AM
|
Replies: 17
Views: 2,159
|
Forum: Model T (1909-1927)
03-22-2021, 03:47 PM
|
Replies: 17
Views: 2,159
Re: timer assy question?
hello redmodel t
i have the copper gasket buti will replace it has been on there a long time. when i turn it off it will back fire
thank you
kevin
|
Forum: Model T (1909-1927)
03-22-2021, 12:59 PM
|
Replies: 17
Views: 2,159
Re: timer assy question?
i have the roller on and coils it runs better but on a slight incline it has no puwer and when shifting into high it stumbles and take a little time to get up to speed. i do not have a compression...
|
Forum: Model T (1909-1927)
03-19-2021, 08:11 PM
|
Replies: 17
Views: 2,159
timer assy question? Update fixed
hello
I have a 1923 t i have had a true fire system for over 30 years but i think it is going bad i am going to switch back to the coils and timer and roller assy my questions is witch way dose the...
|
Forum: Model A (1928-31)
03-12-2021, 04:19 PM
|
Replies: 14
Views: 2,568
|
Forum: Model A (1928-31)
02-26-2021, 09:40 AM
|
Replies: 4
Views: 1,037
|
Forum: Model A (1928-31)
02-25-2021, 05:17 PM
|
Replies: 4
Views: 1,037
Re: Rear axle key orientation
the tapered end faces down (what you are calling the elongated bevel) and facing the backing plate. be sure the it is at the end of the shaft out side hub will go on easier i just finished doing my...
|
Forum: Model A (1928-31)
02-09-2021, 02:39 PM
|
Replies: 9
Views: 1,091
|
Forum: Model A (1928-31)
02-09-2021, 12:59 PM
|
Replies: 9
Views: 1,091
|
Forum: Model T (1909-1927)
02-09-2021, 12:33 PM
|
Replies: 7
Views: 1,217
|
Forum: Model A (1928-31)
02-09-2021, 11:15 AM
|
Replies: 9
Views: 1,091
|
Forum: Model T (1909-1927)
02-09-2021, 11:07 AM
|
Replies: 7
Views: 1,217
1923 roadster running bad need help
hello
my 23 has started to run bad i had the head gasket replaced and all the carbon cleaned, it idles fine but back fires ans loss of power. i do not have a compression gauge. i removed the no 1...
|