Forum: Early V8
06-14-2025, 08:00 AM
|
|
Replies: 0
Views: 326
34 clutch pedal
Looking for a 34 clutch pedal, 40-7520-B or 40-7520-B2 One is the I beam style the other oval like the brake pedal. Not interested in ones that are egg shaped in the bushing area. Thanks
|
|
Forum: Early V8 (1932-53)
03-15-2025, 09:08 AM
|
|
Replies: 10
Views: 2,428
Re: Boot for park brake lever 39 truck
Will you please post that info here as I also have a 39 pickup. My fix was a piece of cardboard taped to the cover until I found something better. Your response is much better.
|
|
Forum: Early V8 (1932-53)
11-16-2024, 09:50 AM
|
|
Replies: 8
Views: 1,329
Re: Rear glass installation 1938 Pick up
This is for your friends truck right. On my 39 the seal goes on the glass and then it is pushed in until it rest against the back of the cab. The garnish is then installed. The screws are at an angle...
|
|
Forum: Early V8 (1932-53)
06-11-2024, 09:28 AM
|
|
Replies: 7
Views: 1,015
Re: 1939 pickup bracket help
The brackets on my 39 pickup are 1 inch wide, .085 thick including paint so just a hair over 1/16 thick. Holes are 3 inches center to center. Holes are oversized 1/4. There are two bends, slight bend...
|
|
Forum: Model A (1928-31)
06-08-2024, 06:39 PM
|
|
Replies: 14
Views: 4,113
Re: 1932 drive shaft
I just pulled an early 32 rear apart. Driveshaft looks close to yours put the taper is threaded near the tube end. Very fine thread but there was no nut installed. What would be the reason for this....
|
|
Forum: Model A (1928-31)
04-30-2024, 05:59 AM
|
|
Replies: 8
Views: 1,446
|
|
Forum: Early V8 (1932-53)
03-11-2024, 08:07 AM
|
|
Replies: 19
Views: 2,328
|
|
Forum: Model-A
12-13-2023, 08:37 AM
|
|
Replies: 1
Views: 816
|
|
Forum: Model-A
12-08-2023, 01:15 PM
|
|
Replies: 1
Views: 816
Model A engine
Model A engine that does turn over. No markings on pistons other than a prick punch to show what bore they go in. Valve chamber has little sludge. There is a spot between 3 and 4 cylinders that had...
|
|
Forum: Early V8 (1932-53)
12-07-2023, 09:20 AM
|
|
Replies: 4
Views: 902
|
|
Forum: Model-A
12-06-2023, 06:54 PM
|
|
Replies: 0
Views: 711
Model B Ford engine
Model B engine with the CB crank that has the weights sweated on. Does turn over. I can not see any cracks in the deck but it does have minor pitting near the valves. Exhaust valves have hardened...
|
|
Forum: Model A (1928-31)
10-26-2023, 08:33 AM
|
|
Replies: 12
Views: 1,867
Re: Please Help with Flywheel Decision
More info would help but I'll share my thoughts. My fenderless 31 roadster ran a stock A engine that was upgraded with a 6-1 head, B cam and downdraft carb. Flywheel was lightened to 42 pounds with...
|
|
Forum: Early V8 (1932-53)
10-07-2023, 07:41 AM
|
|
Replies: 15
Views: 2,081
Re: Is there still a market for a V8-60 race cam?
I had two V8 60 race cams on my table with nos bearings, rods etc. No takers on anything. A vender one row over had two sixty motors one full race another complete but stock, again no takers even...
|
|
Forum: Early V8 (1932-53)
09-23-2023, 08:40 AM
|
|
Replies: 18
Views: 2,231
Re: Gas tank removal -39 pickup
Mine came out the way your describing but there was still slight interference with the bottom of the frame rail. Using a thin flat bar between the mounting edge of the tank and the bottom flange of...
|
|
Forum: Early V8 (1932-53)
08-29-2023, 06:50 AM
|
|
Replies: 5
Views: 1,475
|
|
Forum: Early V8 (1932-53)
05-29-2023, 06:33 AM
|
|
Replies: 15
Views: 3,385
|
|
Forum: Early V8 (1932-53)
05-28-2023, 03:45 PM
|
|
Replies: 15
Views: 3,385
Motor mount spacers
Can someone tell me the thickness of the metal used to make the U shaped spacers that are used when putting a later model flathead in an earlier frame.
|
|
Forum: Model A (1928-31)
07-27-2022, 06:50 AM
|
|
Replies: 9
Views: 2,285
|
|
Forum: Early V8 (1932-53)
06-01-2022, 01:33 PM
|
|
Replies: 8
Views: 1,458
Re: 39 pickup wiper arm
Just got off the phone with Joe from antique auto. He tells me because I have a NOS wiper motor that I need to put the arm on the shaft and tighten up the front nut. This causes the arm to cut the...
|
|
Forum: Early V8 (1932-53)
06-01-2022, 09:06 AM
|
|
Replies: 8
Views: 1,458
Re: 39 pickup wiper arm
No, that nut is removed. Between the threads for that nut and the threads for the wiper motor mount is the six sided piece. I cant load photos to explain it any easier.
|
|
Forum: Early V8 (1932-53)
06-01-2022, 06:11 AM
|
|
Replies: 8
Views: 1,458
Re: 39 pickup wiper arm
I've checked the parts catalog and it does state 37 -39 closed cars and pickups do use the same wiper arm. Still not sure why the one I got is splines. Tried to call Joe's antique auto where I got...
|
|
Forum: Early V8 (1932-53)
05-28-2022, 07:55 PM
|
|
Replies: 8
Views: 1,458
|
|
Forum: Early V8 (1932-53)
05-28-2022, 05:50 PM
|
|
Replies: 8
Views: 1,458
39 pickup wiper arm
The trico wiper for my pickup is a KSB 383-1G. The wiper arm I got is a 78-17529 listed for a 37-39 closed car and pickup. The problem is the arm is splined while the wiper shaft has six sides like a...
|
|
Forum: Early V8 (1932-53)
05-02-2022, 07:21 AM
|
|
Replies: 6
Views: 1,220
|
|
Forum: Early V8 (1932-53)
04-02-2022, 05:15 AM
|
|
Replies: 14
Views: 1,753
Re: Speedometer drive gear
I checked the rear ratio and the turtle gear before I posted the question. My question is are there different drives for the driveshaft or did Ford use two different ratio speedometer. As far as all...
|
