Forum: Early V8 (1932-53)
05-21-2024, 04:03 PM
|
Replies: 11
Views: 555
|
Forum: Early V8 (1932-53)
05-15-2024, 03:39 PM
|
Replies: 39
Views: 1,534
Re: Model B Ford 4 cylinder identification
With what you’re doing I sure would think some more about a B transmission. The missing pieces aren’t hard to find and it is way better than an A transmission. The ‘32 B flywheel housing sorta had...
|
Forum: Early V8 (1932-53)
03-19-2024, 08:31 AM
|
Replies: 18
Views: 950
|
Forum: Early V8 (1932-53)
03-02-2024, 05:20 PM
|
Replies: 38
Views: 2,217
|
Forum: Early V8 (1932-53)
03-01-2024, 01:50 PM
|
Replies: 38
Views: 2,217
|
Forum: Early V8 (1932-53)
02-26-2024, 08:51 PM
|
Replies: 23
Views: 1,078
Re: Need cluster gear idntification
4 slots is 68-7113. 2 prongs is 8M-7113. They are interchangeable but require different thrust washers. 68-7113 takes a one piece thrust washer in back called 68-7129-B. 8M-7113 takes a two piece...
|
Forum: Early V8 (1932-53)
02-23-2024, 06:07 PM
|
Replies: 14
Views: 459
Re: Transmission Main Shaft ID Needed
I think you’re ok there. The MDG with the small cone is used with early synchronizer, stock applications from ‘32 to early ‘39. The other is stock for ‘39-50 - the traditional ‘39 style...
|
Forum: Early V8 (1932-53)
02-23-2024, 05:21 PM
|
Replies: 14
Views: 459
|
Forum: Early V8 (1932-53)
02-23-2024, 03:56 PM
|
Replies: 14
Views: 459
Re: Transmission Main Shaft ID Needed
Just a word of caution when looking at a 16T main drive gear of unknown origin - it could be a 1C rather than an 81A. If 1C it must be paired with the later gears that come in the open drive...
|
Forum: Early V8 (1932-53)
12-21-2023, 11:02 AM
|
Replies: 18
Views: 1,252
|
Forum: Early V8 (1932-53)
07-20-2023, 10:02 AM
|
Replies: 14
Views: 1,636
|
Forum: Early V8 (1932-53)
07-17-2023, 08:03 PM
|
Replies: 14
Views: 1,636
Re: Larry Patton auction in Springfield, Ohio
‘32 rolling chassis was $4,500. I think one of the ‘32 roadster projects went just over $20K and the other was around 15K. Some parts low, some high. There was a lot more than the pictures show...
|
Forum: Early V8 (1932-53)
06-03-2023, 03:29 PM
|
Replies: 14
Views: 1,468
|
Forum: Early V8 (1932-53)
04-12-2023, 07:34 AM
|
Replies: 7
Views: 963
|
Forum: Early V8 (1932-53)
03-27-2023, 02:13 PM
|
Replies: 9
Views: 1,082
Re: 1932 Shift Levers
https://www.fordgarage.com/pages/Btransmissionshiftlevers.htm
Relevant info from Vince Falter’s site
|
Forum: Early V8 (1932-53)
03-27-2023, 01:57 PM
|
Replies: 9
Views: 1,082
Re: 1932 Shift Levers
I have cleaned a lot of these, can’t remember if they have part #s on the stub? Maybe some? I will check that next time I’m in the shop
|
Forum: Early V8 (1932-53)
03-27-2023, 01:36 PM
|
Replies: 9
Views: 1,082
Re: 1932 Shift Levers
Well I don’t know about the ‘32s. Some helpful info already. Not sure about ‘33-34, but sure the lever hasn’t been modified. I looked at both the ‘32 book and the ‘33-34 book and this seems to be...
|
Forum: Early V8 (1932-53)
03-27-2023, 12:20 PM
|
Replies: 9
Views: 1,082
Re: 1932 Shift Levers
I have 2 or 3 levers that are EXACTLY like the one on the far right so I am pretty sure it hasn’t been modified. Think it is ‘33-34
|
Forum: Early V8 (1932-53)
03-27-2023, 10:08 AM
|
Replies: 9
Views: 1,082
1932 Shift Levers
I have read everything I could get my hands on and still have a lot of questions about shift levers in 1932. It appears there are 3-4 different versions but I don’t know if there is any chronology...
|
Forum: Early V8 (1932-53)
03-24-2023, 11:40 AM
|
Replies: 33
Views: 3,602
Re: 1933 Model B and V8 drivetrain differences.
512276 512277
’33-34 has the notches on the sides. ‘33-34 will work for ‘32, but not the other way round.
Apology accepted DavidG, I know you are a wealth of knowledge and I appreciate your...
|
Forum: Early V8 (1932-53)
03-24-2023, 07:57 AM
|
Replies: 33
Views: 3,602
|
Forum: Early V8 (1932-53)
03-24-2023, 06:33 AM
|
Replies: 33
Views: 3,602
|
Forum: Early V8 (1932-53)
01-14-2023, 01:24 PM
|
Replies: 15
Views: 1,606
Re: Shift levers ?
Another reason the 3rd lever looks ‘32ish to me is in the picture it looks about the same length as the ‘35s. A commercial lever (‘40-52) would have a similar bend but is much longer. Things I’ve...
|
Forum: Early V8 (1932-53)
01-14-2023, 12:55 PM
|
Replies: 15
Views: 1,606
Re: Shift levers ?
I could be wrong, need to measure to be sure. Tell tale sign is the short ones are a little crooked looking at the tip just before the ball
|
Forum: Early V8 (1932-53)
01-14-2023, 11:53 AM
|
Replies: 15
Views: 1,606
|