Forum: Early V8 (1932-53)
Yesterday, 11:34 AM
|
Replies: 3
Views: 165
Re: Ford intake with S
Typically, a raised letter, numeral, etc. signifies (IE) the manufacturer, date, mold ID. My guess in this case is this was produced outside of the Ford Motor CO. as a service replacement part....
|
Forum: Early V8 (1932-53)
Yesterday, 10:41 AM
|
Replies: 12
Views: 563
|
Forum: Model A (1928-31)
05-26-2024, 04:36 PM
|
Replies: 4
Views: 151
|
Forum: Model A (1928-31)
05-26-2024, 02:38 PM
|
Replies: 4
Views: 151
light switch install
Hello men!
Might seem simple to you but I'm kinda a newbie to the Model a world so here goes...
The piece on the end of the horn rod (picture attached) ... gets installed at the 3 and 9 o'clock...
|
Forum: Early V8 (1932-53)
05-25-2024, 12:08 PM
|
Replies: 12
Views: 563
Re: What is this ?
FYI, The compression fitting is not only unsafe within the brake line, it's illegal.
|
Forum: Early V8 (1932-53)
05-25-2024, 10:09 AM
|
Replies: 13
Views: 580
|
Forum: Early V8 (1932-53)
05-25-2024, 09:14 AM
|
Replies: 10
Views: 335
Re: Tail light connectore
Yep. They will work but you will need to grind down the diameter a bit. As is, they will not fit the connector.
|
Forum: Early V8 (1932-53)
05-25-2024, 07:26 AM
|
Replies: 13
Views: 518
|
Forum: Early V8 (1932-53)
05-23-2024, 04:16 PM
|
Replies: 10
Views: 340
|
Forum: Early V8 (1932-53)
05-22-2024, 04:30 PM
|
Replies: 11
Views: 564
Re: Banjo rear end hub, axle bearings and seals
The reproductions have a sorted history of poor quality. The cages were not (are not?) hardened properly and rather quickly, the cage would fail and the bearings were free to go where they wanted....
|
Forum: Early V8 (1932-53)
05-22-2024, 08:47 AM
|
Replies: 4
Views: 304
Re: Clutch pedal return spring '40 passenger
Here are two photographs that should help you. Note the hole atop the brace for one end of the spring to attach to.
I believe if you zoom in on the other photograph, you'll be able to see how the...
|
Forum: Early V8 (1932-53)
05-21-2024, 07:03 PM
|
Replies: 13
Views: 580
Re: Rusted 1940 cab
Found one more. I think that's all I have of what you wanted. Hope it helps...
|
Forum: Early V8 (1932-53)
05-21-2024, 04:50 PM
|
Replies: 13
Views: 580
|
Forum: Early V8 (1932-53)
05-21-2024, 02:31 PM
|
Replies: 11
Views: 564
|
Forum: Early V8 (1932-53)
05-20-2024, 08:48 PM
|
Replies: 14
Views: 759
|
Forum: Early V8 (1932-53)
05-20-2024, 07:16 PM
|
Replies: 14
Views: 759
Re: 1932/36 Condenser replacement.
For my cars and those clients that allow me to do what I prefer, I too use the 32's.
I think the last time I bought them; they were about $28. A bargain considering the confidence a guy gets with...
|
Forum: Early V8 (1932-53)
05-20-2024, 02:15 PM
|
Replies: 7
Views: 608
|
Forum: Early V8 (1932-53)
05-18-2024, 01:39 PM
|
Replies: 14
Views: 759
Re: 1932/36 Condenser replacement.
I use a Hunt's Magneto condenser. I have used both the 28mfd and 32mfd units. GREAT reliability. With the coil you are using, solder the original "bracket end" on to the condenser and shove the...
|
Forum: Early V8 (1932-53)
05-18-2024, 01:34 PM
|
Replies: 12
Views: 513
Re: Crab distributor vacuum line
Guys, guys, guys...
That's an incorrect manifold for the 59A. The correct manifold has an integral threaded hole just below the carburetor base. There is a special fitting that allows vacuum to be...
|
Forum: Early V8 (1932-53)
05-18-2024, 07:33 AM
|
Replies: 19
Views: 787
|
Forum: Early V8 (1932-53)
05-17-2024, 09:43 AM
|
Replies: 7
Views: 285
|
Forum: Early V8 (1932-53)
05-17-2024, 07:38 AM
|
Replies: 7
Views: 285
|
Forum: Model A (1928-31)
05-16-2024, 06:01 PM
|
Replies: 12
Views: 731
|
Forum: Model A (1928-31)
05-16-2024, 07:07 AM
|
Replies: 19
Views: 1,026
Re: Lacquer Paint fix?
Just in case some folks don't believe you, I'd like to attest to the truth in your advice.
I used to buy that giant can of black shoe polish marketed as vinyl top dressing. Wax a black or marron...
|
Forum: Early V8 (1932-53)
05-15-2024, 06:01 PM
|
Replies: 11
Views: 1,517
|