Forum: Model A (1928-31)
05-23-2024, 10:53 AM
|
Replies: 4
Views: 268
|
Forum: Model A (1928-31)
05-23-2024, 10:50 AM
|
Replies: 8
Views: 411
|
Forum: Model A (1928-31)
05-22-2024, 10:56 AM
|
Replies: 15
Views: 897
Re: Rear main options
I wouldn't worry about that crack at all. It is in the center of the bearing, and won't go anywhere or cause any problems.
|
Forum: Model A (1928-31)
05-22-2024, 10:51 AM
|
Replies: 17
Views: 782
Re: Rebuilt Engine Options
V8 clutch, the flywheel must be machined, so it becomes flat, and lighter, or better yet a diaphragm clutch, much smoother. The Burtz cam is very nice, but a regrind is MUCH cheaper, and can be...
|
Forum: Model A (1928-31)
05-22-2024, 10:41 AM
|
Replies: 2
Views: 334
Re: GAZ Goodies
Nice! The more you look at it, the more Model A parts you see, mechanically.
|
Forum: Model A (1928-31)
05-21-2024, 12:04 PM
|
Replies: 18
Views: 726
Re: valve guide question
I did what you are contemplating one time on a friend's engine, a year or so later I again opened that engine for a different reason and found that one guide had slipped down nearly a full inch. The...
|
Forum: Model A (1928-31)
05-20-2024, 11:37 AM
|
Replies: 4
Views: 317
Re: Front and rear Hubs
I'm not sure what your question is. If your 'new' hubs have all 5 studs swedged in place, use them. Don't over torque, 60 lbs is very adequate.
|
Forum: Model A (1928-31)
05-20-2024, 11:32 AM
|
Replies: 11
Views: 627
|
Forum: Model A (1928-31)
05-20-2024, 11:30 AM
|
Replies: 12
Views: 775
Re: "New Engine" Balancing"
Balancing a 4 cyl. engine does not have to be done as a unit, the crank, rods, flywheel, etc. can al be done separately.
|
Forum: Model A (1928-31)
05-17-2024, 10:37 AM
|
Replies: 15
Views: 719
Re: cam lube
Assembly lube is the best but either is fine for what you are doing.
|
Forum: Model A (1928-31)
05-11-2024, 11:05 AM
|
Replies: 12
Views: 526
Re: Tight crank gear
I always use a steel gear, a good, old, steel gear is better than a new cast iron gear.
|
Forum: Model A (1928-31)
05-10-2024, 11:08 AM
|
Replies: 12
Views: 526
Re: Tight crank gear
Heat the gear with a oxy/acet or blow torch. Heat it quite but not enough to show any color on it. It should then slip on, at least part way, then gently pound it on all the way. I made a driver...
|
Forum: Model A (1928-31)
05-04-2024, 12:45 PM
|
Replies: 6
Views: 921
Re: Not A, But Interesting
Very interesting! Makes me wonder how Ford and Dodge/Plymouth made their tubular axles in the late 30's? Chrysler also made one but it was a 3-piece unit with riveted on ends.
|
Forum: Model A (1928-31)
05-03-2024, 11:26 AM
|
Replies: 29
Views: 1,822
Re: Sticking valves?
I definitely recommend IMO but also think your rings may be worn, because the compression is slow but fine with oil added. Do the MMO first.
|
Forum: Model A (1928-31)
04-29-2024, 11:26 AM
|
Replies: 11
Views: 932
|
Forum: Model A (1928-31)
04-28-2024, 12:13 PM
|
Replies: 11
Views: 932
Re: Winfield Model M updraft carb
The difference between the S and the SR is that the later has an accelerator pump, not needed IMO. Gasket sets are available. Price depends on size, condition and are they complete with air-horn or...
|
Forum: Model A (1928-31)
04-27-2024, 11:36 AM
|
Replies: 7
Views: 974
Re: Side Water Outlet
The diamond is a genuine Ford part but cast by an outside foundry. That mark can be found on many Ford parts.
|
Forum: Model A (1928-31)
04-27-2024, 11:33 AM
|
Replies: 11
Views: 932
Re: Winfield Model M updraft carb
They were only used on T's. They are better than the stock T carb, but IMO a bit small for the Model A. I've run a few Winfield model S on my warmed up Model A, and really like them.
|
Forum: Model A (1928-31)
04-25-2024, 01:12 PM
|
Replies: 26
Views: 2,345
|
Forum: Model A (1928-31)
04-24-2024, 11:22 AM
|
Replies: 26
Views: 2,345
|
Forum: Model A (1928-31)
04-22-2024, 11:43 AM
|
Replies: 1,413
Views: 330,502
|
Forum: Model A (1928-31)
04-21-2024, 12:47 PM
|
Replies: 13
Views: 2,573
|
Forum: Model A (1928-31)
04-18-2024, 11:08 AM
|
Replies: 13
Views: 2,573
|
Forum: Model A (1928-31)
04-17-2024, 11:48 AM
|
Replies: 2
Views: 521
|
Forum: Model A (1928-31)
04-17-2024, 11:46 AM
|
Replies: 13
Views: 2,573
|