Forum: Early V8 (1932-53)
Today, 01:39 PM
|
Replies: 9
Views: 346
|
Forum: Early V8 (1932-53)
Today, 11:54 AM
|
Replies: 5
Views: 532
|
Forum: Early V8 (1932-53)
Today, 11:17 AM
|
Replies: 9
Views: 292
|
Forum: Early V8 (1932-53)
Today, 11:10 AM
|
Replies: 9
Views: 292
Re: Timing advance plate - Crab Distributor
Here you go ....
I set the distributor up using the static method shown in early bulletins and also on Van Pelts site. Note that this is a rebuilt distributor that I got from Drake or Carpenter...
|
Forum: Early V8 (1932-53)
Today, 06:22 AM
|
Replies: 9
Views: 292
|
Forum: Early V8 (1932-53)
Yesterday, 04:00 PM
|
Replies: 9
Views: 292
|
Forum: Early V8 (1932-53)
Yesterday, 03:34 PM
|
Replies: 353
Views: 24,503
|
Forum: Early V8 (1932-53)
Yesterday, 02:24 PM
|
Replies: 9
Views: 292
|
Forum: The Test Forum
Yesterday, 02:22 PM
|
Replies: 90
Views: 22,149
|
Forum: Early V8 (1932-53)
Yesterday, 08:05 AM
|
Replies: 5
Views: 532
Re: Setting Ignition Points - 59AB
Well I got my distributor setup nicely now using my homemade dwell meter.
It started immediately yesterday afternoon, runs great with no pinging. Very happy now with the original distributor. I plan...
|
Forum: Early V8 (1932-53)
05-24-2024, 04:16 PM
|
Replies: 13
Views: 387
Re: engine stumbles under load
Just took it out for a short test ride and it is working great, great power, no pings all is wonderful! Tomorrow may be a different story :-)
Thanks for the tip Ggmac and yes it is now back to...
|
Forum: Early V8 (1932-53)
05-24-2024, 09:35 AM
|
Replies: 13
Views: 387
Re: engine stumbles under load
No, looking for about 3 amps so the points will last longer This is from a recent post I made:
"I had a running and starting issue this week so I'm replacing my Petronix II with a Bob Drake...
|
Forum: Early V8 (1932-53)
05-24-2024, 07:24 AM
|
Replies: 13
Views: 387
Re: engine stumbles under load
For a 12 V system you'll want to target about 4 ohms total resistance, sum of the coil's primary resistance plus an external ballast resistor.
Glenn
|
Forum: Early V8 (1932-53)
05-22-2024, 05:21 AM
|
Replies: 22
Views: 854
|
Forum: The Test Forum
05-22-2024, 05:20 AM
|
Replies: 90
Views: 22,149
|
Forum: Early V8 (1932-53)
05-21-2024, 11:23 AM
|
Replies: 3
Views: 233
Re: O2 bung question
IMPORTANT INSTALLATION NOTE - UEGO Sensor Mounting Orientation
A weld-in M18 X 1.5 boss is supplied for sensor installation. Mount the O2 sensor in the
exhaust system at least 18 inches downstream...
|
Forum: The Test Forum
05-21-2024, 11:22 AM
|
Replies: 90
Views: 22,149
|
Forum: Early V8 (1932-53)
05-20-2024, 09:30 AM
|
Replies: 7
Views: 491
Re: Bump steer
Yes, many copy cats following awful setups. Good article here:
https://www.motortrend.com/how-to/solid-axle-front-suspension-details/
|
Forum: Early V8 (1932-53)
05-19-2024, 03:59 PM
|
Replies: 5
Views: 532
Re: Setting Ignition Points - 59AB
Yes, but that is for setting the timing with the two scales. Good post like Van Pelt has on his site. I'm after a reasonable way to get as accurate as I can for the gaps and dwell.
Thanks.\,...
|
Forum: Early V8 (1932-53)
05-19-2024, 09:51 AM
|
Replies: 5
Views: 532
Setting Ignition Points - 59AB
Hi,
I got lost on the internet yesterday and this morning looking for a DIY precise way of setting ignition points.
First, I found a great video from Mart,...
|
Forum: Early V8 (1932-53)
05-17-2024, 03:43 PM
|
Replies: 55
Views: 2,578
Re: Hot rod steering box
I don't understand why you are against an F-1 box.
Regarding the Hudson 1939 with a longer shaft than the '37 another ??
NealinCA posts on the HAMB, not here.
3" chop is too much. Any dip in...
|
Forum: Early V8 (1932-53)
05-16-2024, 09:53 AM
|
Replies: 5
Views: 197
|
Forum: Early V8 (1932-53)
05-16-2024, 08:57 AM
|
Replies: 5
Views: 197
Re: Automotive switch ratings?
Thanks Tubman
I used a lower voltage due to the drop when I'm starting up with the foot mounted starter switch, no solenoid.
Even so 13.6v X 6a = 81.6 watts
a question of the ratings,...
|
Forum: Early V8 (1932-53)
05-16-2024, 08:36 AM
|
Replies: 5
Views: 197
Automotive switch ratings?
I had a running and starting issue this week so I'm replacing my Petronix II with a Bob Drake rebuilt 1942 crab distributor on my 59AB. I'm planning to add a ceramic 1.5 ohm inline with the coil's...
|
Forum: Early V8 (1932-53)
05-15-2024, 02:56 PM
|
Replies: 36
Views: 1,627
Re: Oil leak
You may be able to pull the pan by rotating the motor. Either #1 or#5 rod bearing caps may be causing the hangup.
Firing order is 1-5-4-8-6-3-7-2
|