Go Back   The Ford Barn > Search Forums
Reload this Page Search Results

Sponsored Links (Register now to hide all advertisements)

Page 1 of 9 1 2345 Last »
Showing results 1 to 25 of 220
Search took 0.02 seconds. Search: Posts Made By: dansluck
Forum: Model A (1928-31) Yesterday, 07:58 PM
Replies: 3
Views: 267
Posted By dansluck
Re: just a quickie

1.5 inches at the crank shaft end, 1inch at the piston pin
Forum: Model A (1928-31) 05-13-2024, 08:14 PM
Replies: 25
Views: 2,077
Posted By dansluck
Re: getting into the Rumble Seat

Our church does a "Trunk er Treat" on 10/31. I give rides to the kids and wanta be kids around the church. I always tie the rumble seat lid to the spare incase of a sudden stop.
Forum: Model A (1928-31) 05-13-2024, 07:56 PM
Replies: 3
Views: 413
Posted By dansluck
Re: Henry and Edsel again

Wonder where it is now.
Forum: Model A (1928-31) 04-12-2024, 12:49 PM
Replies: 136
Views: 11,552
Posted By dansluck
Re: Misfire mystery

Good Job on a Tough Find
Forum: Model A (1928-31) 03-05-2024, 12:09 AM
Replies: 12
Views: 1,030
Posted By dansluck
Re: 2 HP hotrod

Has an exhaust problem. Could get a little messy with the windshield open.
Forum: Model A (1928-31) 02-13-2024, 03:45 PM
Replies: 7
Views: 1,018
Posted By dansluck
Re: New cast iron rear drums

Knapp,this happened to me also.
Forum: Model A (1928-31) 01-20-2024, 08:24 PM
Replies: 22
Views: 1,459
Posted By dansluck
Re: pulling engine?

I just pull the engine. When i am reinstalling the engine I jack up the tranny a little and install the engine by turning the engine over with a 1 5/16 socket to get the clutch splines to match. ...
Forum: Model A (1928-31) 12-17-2023, 09:04 PM
Replies: 24
Views: 5,960
Posted By dansluck
Re: Snyder's Head Gasket Recommendations or Feedback?

I use copper head gaskets and spray sealant. I torque to 55lbs run it retorque after running at least 2 more times. Good Luck
Forum: Model A (1928-31) 09-19-2023, 09:14 PM
Replies: 9
Views: 1,681
Posted By dansluck
Re: Crank Bearing Problem

Berts counterweights cranks.
Forum: Model A (1928-31) 08-25-2023, 08:19 PM
Replies: 21
Views: 1,987
Posted By dansluck
Re: new fuel tank availability / advice? 31 PU

My 31 has an early 30 gas tank that uses the 29 style dash plate. Works for me but you will want to check that. Good Luck
Dan
Forum: Model A (1928-31) 08-08-2023, 03:52 PM
Replies: 47
Views: 4,447
Posted By dansluck
Re: black wall tires

Goodyear diamond tread.
Forum: Model A (1928-31) 06-19-2023, 06:21 PM
Replies: 19
Views: 3,360
Posted By dansluck
Re: "Modern" Shocks from Snyders

Love my Monroes , 35 wheels and 600 tires. 2 miles of dirt road to county paved road and they do the job great.
Forum: Model A (1928-31) 05-30-2023, 05:21 PM
Replies: 37
Views: 4,554
Posted By dansluck
Re: New Radiator Opinions

Geezer
I drove from Nevada across the Sierras and across the Central Valley t the Bay Area in 94 degree weather and did not overheat. Brassworks Radiatior.

Dan
Forum: Model A (1928-31) 03-12-2023, 08:18 PM
Replies: 9
Views: 1,637
Posted By dansluck
Re: 1933-1934 4 Cylinder Parts

Tim, Can you turn down a Model A pulley to shorten it to the correct length ?
Forum: Model A (1928-31) 03-05-2023, 10:57 PM
Replies: 46
Views: 8,080
Posted By dansluck
Re: modern shock upgrade

I use shocks from Ken Davis, both front and back. I drive 2 miles of dirt road to get to county road and they work great.
Forum: Model A (1928-31) 02-11-2023, 09:31 PM
Replies: 3
Views: 902
Posted By dansluck
Re: Is this a Police Head?

Looks like the Police head I have.
Good Luck
Dan
Forum: Model A (1928-31) 01-22-2023, 09:44 PM
Replies: 18
Views: 2,636
Posted By dansluck
Re: remember when

Synchro909,
Driving my Model A in 15 degree weather makes me wish for righthand drive to be near the heater.
Forum: Model A (1928-31) 01-17-2023, 12:02 AM
Replies: 15
Views: 2,166
Posted By dansluck
Re: Dash light always on

What type of speedometer do you have? Round or oval. I have a 1931 that has the oval type. The light is in the center of the dash panel like on a 1929. It is odd but sometimes odd things were used...
Forum: Model A (1928-31) 01-08-2023, 12:39 AM
Replies: 41
Views: 9,246
Posted By dansluck
Re: Engine bearing questions

Dodge
Who is the supplier of that seal, and do you have a part #?
Thanks
Forum: Model A (1928-31) 01-08-2023, 12:22 AM
Replies: 44
Views: 8,832
Posted By dansluck
Re: Update on ecklers........

Zax40
When you get an email you want to get rid of, block or unsubscribe right click it, like you were going to open it only right click, then choose from the menu.
Good Luck
Dan
Forum: Model A (1928-31) 12-28-2022, 07:00 PM
Replies: 41
Views: 9,246
Posted By dansluck
Re: Engine bearing questions

Working under your car gives your hair that oiled and combed back 1930's look.
But I would pull the engine it is more enjoyable.
Dan
Forum: Model A (1928-31) 12-25-2022, 05:59 PM
Replies: 19
Views: 2,604
Posted By dansluck
Re: Rear axle/drum question

I've been driving Model A's for 60 some odd years. In high school I learned if you abuse them, you shear axle keys. I use the shims if the axle surface warrant it. I torque to 80 lbs and then align...
Forum: Model A (1928-31) 12-25-2022, 05:19 PM
Replies: 11
Views: 1,732
Posted By dansluck
Re: Santa delivered!!

" Gasoline additive." Helps to keep the feet warm.

Merry Christmas
Dan
Forum: Model A (1928-31) 12-16-2022, 12:00 AM
Replies: 24
???
Views: 3,462
Posted By dansluck
Re: ???

You will get a flicker in your rear-view mirror as you pass your own light.
Dan
Forum: Model A (1928-31) 12-15-2022, 11:54 PM
Replies: 16
Views: 8,487
Posted By dansluck
Re: Model A Engine Noise and worn timing gear

If you don't have Les Andrew's Red Book', I would recommend getting it. You will need a special tool to remove the nut on the timing gear. Andrew's book gives step by step instructions. Bert's part...
Showing results 1 to 25 of 220
Page 1 of 9 1 2345 Last »

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 11:56 PM.