Forum: Late V8 (1954+)
05-31-2024, 05:23 PM
|
Replies: 9
Views: 323
Re: Whatisit?
Thank you very much. Would it be good to get it cleaned up or put it out there as is? Don’t believe I will get into this, got too many flatheads
|
Forum: Late V8 (1954+)
05-31-2024, 08:33 AM
|
Replies: 9
Views: 323
Re: Whatisit?
Fresh views, pulled it out of a semi trailer Wednesday, dealership cleaned out in ‘79, suppose I should get it cleaned even though I am not going to use it.
|
Forum: Late V8 (1954+)
05-30-2024, 05:50 PM
|
Replies: 9
Views: 323
Whatisit?
Have a NOS block, dunno what, I am going to get the light rust boiled off, code says 4 bolt main but not seeing that. Know flatheads & learning 289’s but not these things. Ideas?
|
Forum: Early V8 (1932-53)
05-30-2024, 02:44 PM
|
Replies: 0
Views: 113
Spark plug ID
I am trying to locate a cross reference chart or ideal to get a Blue Crown book, I have spark plugs I want to sort and determine application. If someone has images of pages from a book that would...
|
Forum: Early V8
05-30-2024, 02:37 PM
|
Replies: 0
Views: 70
Blue Crown Spark plug chart
Hi, looking for a booklet or chart to find out what spark plugs go to what, would like to buy original or get photos of pages.
|
Forum: Early V8 (1932-53)
05-10-2024, 09:28 PM
|
Replies: 12
Views: 409
|
Forum: Early V8 (1932-53)
01-12-2024, 09:56 PM
|
Replies: 10
Views: 699
|
Forum: Early V8 (1932-53)
12-06-2023, 10:14 AM
|
Replies: 33
Views: 4,265
Re: 1937 model 74 blowing the blues
I have some oddball (since I don’t have any 60’s) valves, if I knew the overall length maybe that’s what they are. Longer than my 21 stud mushrooms. Can have them if fit
|
Forum: Late V8
12-03-2023, 08:18 PM
|
Replies: 0
Views: 501
Bellhousing & such, 289
Have a motor 289, & 3 speed transmission, need all the stuff to go between. Fork, fulcrum, spring, plate& bell, flywheel clutch. Somewhere in fl, south Alabama, south ga.
|
Forum: Early V8 (1932-53)
10-21-2023, 08:17 AM
|
Replies: 10
Views: 694
Re: 48 Ford how much play on rear driveshaft yoke
Drag should be something like 1.7 in # I thought, rather than toggle something up I elected to do it by “ feels good” that is enclosed, but same thing. If it feels gritty, I would pull it out &...
|
Forum: Early V8 (1932-53)
10-21-2023, 08:03 AM
|
Replies: 23
Views: 1,774
|
Forum: Model A (1928-31)
07-17-2023, 11:44 AM
|
Replies: 24
Views: 2,327
Re: How much oil from L to notch on dipstick?
My White Construcktor 855 motor held 5 gallons, add mark was 2 quarts low. Starting out every morning I topped it off, most of 2 quarts Rotella. After a couple weeks, I let it go, and it stayed at...
|
Forum: Early V8 (1932-53)
03-12-2023, 10:55 AM
|
Replies: 9
Views: 1,306
|
Forum: Early V8 (1932-53)
02-11-2023, 05:40 PM
|
Replies: 15
Views: 1,913
|
Forum: Early V8 (1932-53)
02-11-2023, 09:54 AM
|
Replies: 15
Views: 1,913
Re: Help with engine Id
Not to be smart, but lots of previous discussion on it. Challenging enough, without looking for another block. I went overboard and did a stand with exhaust mounts on both sides....
|
Forum: Early V8 (1932-53)
02-10-2023, 10:30 AM
|
Replies: 15
Views: 1,913
|
Forum: Model A (1928-31)
02-07-2023, 11:21 AM
|
Replies: 13
Views: 2,299
Re: frame repair
I have a right side rail for repair of a frame that was stored in the mud on that side. A challenge to rivet back in but… I recall it was pretty good. Since the left side has the vehicle has your ID...
|
Forum: Early V8 (1932-53)
01-26-2023, 07:49 PM
|
Replies: 8
Views: 1,001
|
Forum: Early V8 (1932-53)
01-16-2023, 08:38 AM
|
Replies: 25
Views: 4,092
Re: wide 5s
I have one like that, someone put a split rim outer rim on a center from a wide 5. Very heavy, and a crappy weld job. There should be a rim with the same ID as wide 5, junkyard shopping with a ruler....
|
Forum: Early V8 (1932-53)
01-16-2023, 08:21 AM
|
Replies: 20
Views: 3,674
|
Forum: Early V8 (1932-53)
01-14-2023, 11:01 AM
|
Replies: 91
Views: 10,988
Re: '36 221 - rebuildable??
I have been collecting bearing sets as they come up cheap for about 30 years, I can see what I have for full floating. I have 2 early motors that are not fresh so after I have saved some for that no...
|
Forum: Model A (1928-31)
01-10-2023, 10:34 AM
|
Replies: 20
Views: 5,167
Re: Re-Stamping Engine Number / Frame Number
I lived there for way too long. DMV does not want to let you get what you need, their goal is to deny. No ‘spect for any NY bureaucracy. Pennsylvania was much better, Florida I get everything done...
|
Forum: Early V8 (1932-53)
12-12-2022, 11:44 AM
|
Replies: 5
Views: 867
|
Forum: Early V8 (1932-53)
12-08-2022, 09:42 AM
|
Replies: 91
Views: 10,988
|
Forum: Model A (1928-31)
08-24-2022, 05:34 PM
|
Replies: 7
Views: 1,266
|