Forum: Model A (1928-31)
05-23-2024, 11:05 PM
|
Replies: 98
Views: 22,180
Re: 16" Wheels
When I put 600-16's in the fender well of my '31 I had to let the air out and carry a pump.
Charlie Stephens
|
Forum: Early V8 (1932-53)
05-19-2024, 01:42 PM
|
Replies: 11
Views: 467
|
Forum: Early V8 (1932-53)
05-19-2024, 09:54 AM
|
Replies: 10
Views: 472
Re: 1934 hydraulic rear brakes
If I didn't go to Boling Bros I would use '40-'48 Ford brakes. Remember pre and post war were slightly different and I would prefer the post war but at least make them all the same. I have them on...
|
Forum: Early V8 (1932-53)
05-15-2024, 11:06 PM
|
Replies: 39
Views: 1,443
Re: Model B Ford 4 cylinder identification
The rear mount for the Model B transmission was a flat plate that bolted to the "K" member in the '32 frame. The center was isolated in rubber to reduce vibration.
Charlie Stephens
|
Forum: Early V8 (1932-53)
05-15-2024, 11:00 PM
|
Replies: 39
Views: 1,443
Re: Model B Ford 4 cylinder identification
The Model A flywheel will work on the Model B motor. If you decide to run a Model B transmission you will need to cut down the the Model A flywheel to clear the bell housing which has probably...
|
Forum: Model A (1928-31)
05-15-2024, 09:12 PM
|
Replies: 11
Views: 618
Re: Model B Block Boss on side of block
Ford engineers were developing a vacuum assisted clutch and this was where the vacuum cylinder mounted. The unit never made it to production but a lot of motors were produced with this boss. The...
|
Forum: Early V8 (1932-53)
05-10-2024, 08:36 PM
|
Replies: 12
Views: 383
Re: 33 turn signals
I always liked fog lights, either on the bumper bracket or on the bumper.
Charlie Stephens
|
Forum: Early V8 (1932-53)
05-09-2024, 08:45 PM
|
Replies: 39
Views: 1,443
Re: Model B Ford 4 cylinder identification
I doubt a '33-'34 engine was pulled from a '32. Here is a picture of the front cover for a '33-'34. Note that the mount for the generator sets the generator back towards the rear of the car to...
|
Forum: Early V8 (1932-53)
05-07-2024, 12:26 PM
|
Replies: 39
Views: 1,443
Re: Model B Ford 4 cylinder identification
I did exactly what you are asking about several years ago. The engine in my ’31 RDPU was tired and need to be replaced. I had a recently rebuilt “B” engine under the bench. I kept the Model A...
|
Forum: Early V8 (1932-53)
05-06-2024, 11:23 PM
|
Replies: 16
Views: 734
|
Forum: Early V8 (1932-53)
05-06-2024, 02:38 PM
|
Replies: 5
Views: 546
Re: Truck for sale
Be sure to include your general location when you place the ad.
Charlie Stephens
|
Forum: Early V8 (1932-53)
05-06-2024, 02:34 PM
|
Replies: 39
Views: 1,443
|
Forum: Questions & Suggestions
05-05-2024, 01:55 PM
|
Replies: 2
Views: 204
Re: BB Ford wheel lock tings
You posted in a seldom read or replied to section intended for questions to the editors about the site. You should post here: https://www.fordbarn.com/forum/forumdisplay.php?f=4
Welcome
...
|
Forum: Model A (1928-31)
05-04-2024, 03:58 PM
|
Replies: 8
Views: 1,057
Re: Fans
The "Green Bible" was the parts list used by the counter men in the parts department in the fifties showing the early parts. Ford assigned part number B or 18 for all parts used in 1932. This...
|
Forum: Model A (1928-31)
05-03-2024, 12:56 PM
|
Replies: 8
Views: 1,057
Re: Fans
I have never heard of an A or AA truck coming from the factory with a 4 blade fan. I have never seen a Model A part number for a 4 blade fan. The '32 four cylinder engine used the late 1931 Model...
|
Forum: Model A (1928-31)
05-02-2024, 08:27 PM
|
Replies: 8
Views: 1,057
Re: Fans
Not Model A but they will fit. 1933-34 4 cylinder, part number 46 8600
Charlie Stehens
|
Forum: Model A (1928-31)
04-29-2024, 07:13 PM
|
Replies: 9
Views: 836
Re: Block Restamp
Be very careful on this. If your vehicle is registered with your engine number that doesn't match your title and you change it you can get in a lot of trouble with the authorities.
Charlie...
|
Forum: Model A (1928-31)
04-29-2024, 07:09 PM
|
Replies: 13
Views: 896
|
Forum: Early V8 (1932-53)
04-28-2024, 10:56 PM
|
Replies: 25
Views: 1,111
|
Forum: Early V8 (1932-53)
04-26-2024, 04:54 PM
|
Replies: 25
Views: 1,111
|
Forum: Early V8 (1932-53)
04-24-2024, 12:36 PM
|
Replies: 51
Views: 4,406
|
Forum: Early V8 (1932-53)
04-22-2024, 12:46 PM
|
Replies: 4
Views: 429
Re: 32 b frame for v8
First I want to be sure I understand the question. You are looking for the difference between the 1928-1931 Model A frame and the 1932 Model B frame? You intend to use a flathead V8 engine? Either...
|
Forum: Model A (1928-31)
04-15-2024, 12:31 PM
|
Replies: 27
Views: 2,661
|
Forum: Model A (1928-31)
04-11-2024, 11:23 PM
|
Replies: 20
Views: 1,375
|
Forum: Model A (1928-31)
04-11-2024, 11:21 PM
|
Replies: 20
Views: 1,375
|