The Ford Barn - 1946-1948 Ford truck Centersection what's it worth

The Ford Barn (https://www.fordbarn.com/forum/index.php)

- Early V8 (1932-53) (https://www.fordbarn.com/forum/forumdisplay.php?f=4)

- - 1946-1948 Ford truck Centersection what's it worth (https://www.fordbarn.com/forum/showthread.php?t=90116)

Dutchtreat

11-26-2012 03:37 PM

1946-1948 Ford truck Centersection what's it worth

I am cleaning out the Garage and have a 1946-1948 Truck(open) centersection. I also have a set of Car 42-48 bells and a complete diff with axles to go with it. :D

bgarrett

11-26-2012 04:50 PM

Re: 1946-1948 Ford truck Centersection what's it worth

$319.47

Dutchtreat

11-26-2012 04:54 PM

Re: 1946-1948 Ford truck Centersection what's it worth

So How did you arrive at that number??ha ha

Tim Ayers

11-26-2012 08:28 PM

Re: 1946-1948 Ford truck Centersection what's it worth

That x-member goes from between $50-$100. Depends on condition and how it was removed. If torched and with rust pits, low side of price range. If no rust pits and rivits were removed, then higher side of range.

PeteVS

11-26-2012 08:50 PM

Re: 1946-1948 Ford truck Centersection what's it worth

Quote:

Originally Posted by Tim Ayers (Post 541788)

That x-member goes from between $50-$100. Depends on condition and how it was removed. If torched and with rust pits, low side of price range. If no rust pits and rivits were removed, then higher side of range.

Tim: I think he's talking about the banjo casting with the parts for a yoke for an open driveshaft, not a center crossmember. (Are you thinking F1 center crossmember?)

Dutch: The axle bell values will probably hang on the condition of the rear hub bearing surfaces. If those surfaces are worn, that's a lot of $ to get them back to usable.

Tim Ayers

11-26-2012 09:21 PM

Re: 1946-1948 Ford truck Centersection what's it worth

Quote:

Originally Posted by PeteVS (Post 541800)

Tim: I think he's talking about the banjo casting with the parts for a yoke for an open driveshaft, not a center crossmember. (Are you thinking F1 center crossmember?)

Dutch: The axle bell values will probably hang on the condition of the rear hub bearing surfaces. If those surfaces are worn, that's a lot of $ to get them back to usable.

Yep, you're right Pete. Thanks for point that out.

4tl8ford

11-27-2012 08:06 AM

Re: 1946-1948 Ford truck Centersection what's it worth

The 48 and newer Ford Trucks were completely different that 47 and older, Chassis, Engine, Drive Train, Sheet metal.

Dutchtreat

11-27-2012 09:05 AM

Re: 1946-1948 Ford truck Centersection what's it worth

Ok Guys this is the Open Drive Truck banjo that everyone wants to replace there torque-tube with. The bells are rough but rebuild-able. So I'll shoot for $150.00OBO Thanks guys.

Tim Ayers

11-27-2012 10:42 AM

Re: 1946-1948 Ford truck Centersection what's it worth

Dutchtreat:

I sent you a PM. Depending on condition and ratio, I'm intersted. Thanks.

Tim

All times are GMT -5. The time now is 07:48 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2026, vBulletin Solutions Inc.