Question about 1938 Ford pickup 3 Attachment(s)
I have a truck titled as a 1938 Ford. It is a parts truck but it does not have the wide lug pattern like the other 38 I have. Plus the wheels are 14 inch and it has stock hydraulic brakes on it. Just wondering what it really is??? Do 39 cars have the same bolt pattern as a pickup?
|
Re: Question about 1938 Ford pickup Sounds like to me that someone converted your '38 to hydraulic brakes and used '40 or later components. '38 would have had mechanical brakes and wide five wheels. If they had used '39 hydraulics it would have have wide five wheels. Hard to say exactly because lots of parts were swapped around during conversions over the years.Don't know about the wheels because the appear to be 5 on 5 1/2 so the fact that they are 14's is odd.
|
Re: Question about 1938 Ford pickup I think '57-'58 Chrysler imperials had 14" 5 on 5 1/2 wheels. A friend had them on a '40 Ford (with a set of Atlas Bucrons) in the early '60's.
They were hard to find even back then; don't let them get away. |
Re: Question about 1938 Ford pickup Chrysler wheels. Lancer hubcaps were also popular at one time
|
Re: Question about 1938 Ford pickup It depends on whether it has 5 1/2" X 5 lug pattern. If it had 4 3/4" lug pattern then it likely has newer spindles & brakes.
When you say stock hydraulics you need to consider that 1939 was the first year for hydraulics on Ford vehicles. It sounds like it's been updated to me. |
Re: Question about 1938 Ford pickup .
Heck, you don't even have to convert to hydraulics. It's possible just to replace the wide-five drums/hubs (12" dia.) with '40-'48 5 X 5-1/2" drums/hubs (also 12" dia.). Although those do look like the 5-1/2" bolt pattern, the wheels may very well be the Chryslers that Denny (tubman) speaks of. And boy, do I remember the "squawl" that a pair of smokin' "Bucrons" could make! DD |
Re: Question about 1938 Ford pickup A 38 would also already have the 37/40 round back spindles. Besides the backing plates you just need a set of 39 pedals and cut the hole open for them to fit.
Could also be a 39 titled as a 38. 38 had a slightly different grill and hood ornament/latch handle |
Re: Question about 1938 Ford pickup "Parts Truck"? Hell up here that would be a prime candidate for restoration. Heck, it even has a door!
|
Re: Question about 1938 Ford pickup Does the dash have an ash tray in the center? 38 does and 39 does not. door inside panels are different: pressboard or steel?
|
Re: Question about 1938 Ford pickup 1 Attachment(s)
It does have the ash tray in it so I guess its a 38. Good to know. I'll try to post a picture of the NOT parts truck.
|
Re: Question about 1938 Ford pickup Another way to tell the is that the '38 has the front windshield "T" shaped crank handle coming out the face of the dash top. The 39 has a round knob on top of the dash.
|
Re: Question about 1938 Ford pickup https://www.fordbarn.com/forum/attac...p;d=1599257592
Here is a comparison picture of the 1938 and 1939 Ford Pickup (& Truck) Grilles. When you look closely, you will notice that they are completely different., mainly down the middle section. |
Re: Question about 1938 Ford pickup https://www.fordbarn.com/forum/attac...p;d=1599183313
When you check the Grille on your Pickup, you will see that it is a 1938 model. Compare your Grille with the photo in my previous Post. |
Re: Question about 1938 Ford pickup https://www.fordbarn.com/forum/attac...p;d=1598846711
After posting a larger picture of your Pickup, I realised that you already know that that one is a 1938 model. I believe that this is the one that you are inquiring about? Unfortunately, the Grille doesn't show up good at this angle? |
Re: Question about 1938 Ford pickup .
IF the engine has 21-stud heads, it has to be a '38, assuming original engine. Can you read the serial number on that left-side frame rail? That'll tell us for sure what it is. DD |
Re: Question about 1938 Ford pickup Quote:
|
Re: Question about 1938 Ford pickup Frame serial number is the way to go here. That will tell you what the chassis is and if it has the original transmission, that number should match as well.
|
All times are GMT -5. The time now is 09:17 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.