The Ford Barn

The Ford Barn (https://www.fordbarn.com/forum/index.php)
-   Early V8 (1932-53) (https://www.fordbarn.com/forum/forumdisplay.php?f=4)
-   -   Oil pan 59AB photos (https://www.fordbarn.com/forum/showthread.php?t=156253)

Flysafe 01-06-2015 07:59 AM

Re: Oil pan 59AB photos
 

1 Attachment(s)
Hello all,


Some progress in the drawing, left side block, the lines of the back is not done yet. Now they are aligned.

All the best,
Jorge

Flysafe 01-24-2015 03:41 PM

Re: Oil pan 59AB photos
 

I need some help, which side have the bigger angle in the valves?

JSeery 01-24-2015 04:25 PM

Re: Oil pan 59AB photos
 

1 Attachment(s)
Are you looking for the angles? 52.09 on the left and 49.36 on the right.

Flysafe 01-26-2015 08:02 AM

Re: Oil pan 59AB photos
 

Thank you :).

Flysafe 02-01-2015 10:31 AM

Re: Oil pan 59AB photos
 

Hello all,

Now with a few more things, the funny part will begin, extrude all the lines.
The valves sets is done with the correct angle. I will need to resize some parts not serious.


http://i141.photobucket.com/albums/r...ps07f94420.jpg

Flysafe 02-04-2015 07:57 AM

Re: Oil pan 59AB photos
 

Does anyone has a piston for a bore 3.1875 that can take a measurement?
-Height,
-From the bottom to the middle of the piston pin,
-The pin diameter.

Thank you so much.

JSeery 02-04-2015 11:33 AM

Re: Oil pan 59AB photos
 

See if any of this helps. This piston is from a 1948 59a engine, it is domed top, 3.188 +.040 (original 3.188 bored std .040 over).

From top edge of piston to bottom of longest part of skirt: 2.960
From top edge of piston to bottom of shortest part of skirt: 2.700 (not including notch)
Width of longest part of skirt: ~1.250
Width of shortest part of skirt: ~1.250
It is curved between these sections.
From top edge of piston to top of dome: ~.250

Starting a top edge of piston working down to shortest part of skirt (not including notch).
Top edge to top piston ring: .250
Top piston ring grove: .096
Top piston ring to second piston ring: .156
Second piston ring grove: .096
Second piston ring to third piston ring: .100
Third piston ring grove: .188
Third piston ring to top of piston pin: .268
Piston pin: .750
Bottom of piston pin to bottom piston ring: .170
Bottom piston ring grove: .183
Bottom piston ring to bottom of skirt: .440 (not including notch)

From Top edge of piston to center of piston pin: ~1.530
From center of piston pin to bottom of skirt: ~1.170
Piston Pin diameter: .750

These are measurements straight from a piston using calipers and include measuring errors I am sure!

JSeery 02-04-2015 11:35 AM

Re: Oil pan 59AB photos
 

2 Attachment(s)
For some reason the photos didn't load the first time.

Flysafe 02-05-2015 06:44 AM

Re: Oil pan 59AB photos
 

Thank you so much JSeery.

Flysafe 02-05-2015 10:22 AM

Re: Oil pan 59AB photos
 

2 Attachment(s)
Earlier I do this type of piston, can be used in this engine model?

JSeery 02-05-2015 11:03 AM

Re: Oil pan 59AB photos
 

There are 3 ring and 4 ring pistons. I believe the original design from Ford was the 4 ring and the 3 ring was a more modern replacement. Not sure it would make any difference for what you are doing, a lot of the current rebuilds use the 3 ring style.

Flysafe 02-06-2015 07:06 AM

Re: Oil pan 59AB photos
 

Thanks.

Flysafe 02-08-2015 09:30 AM

Re: Oil pan 59AB photos
 

2 Attachment(s)
Hello all,

Some of the lines after extruder.

Flysafe 03-25-2015 04:53 PM

Re: Oil pan 59AB photos
 

2 Attachment(s)
Some progress in the design.

Flysafe 03-30-2015 11:42 AM

Re: Oil pan 59AB photos
 

2 Attachment(s)
Hello all,

Exhaust channels done, and e few holes. Start the front end of the block.

Flysafe 04-06-2015 10:44 AM

Re: Oil pan 59AB photos
 

1 Attachment(s)
Hello all,

The 59 AB block have the yellow line that I made?
The block 8 BA have this fill.

Thank you so much.

Flysafe 04-07-2015 12:15 PM

Re: Oil pan 59AB photos
 

Hello all,

I 'm working in the front end of the block, I will need some help, someone have any photos where I can see the front end of the block 59 AB without the water pumps and the distributor cover? I already made a google search but not find anything.

Thank you so much for the help.

All the best,
Jorge

JSeery 04-07-2015 12:51 PM

Re: Oil pan 59AB photos
 

I can add some in about an hour.

Flysafe 04-08-2015 05:17 AM

Re: Oil pan 59AB photos
 

Quote:

Originally Posted by JSeery (Post 1065025)
I can add some in about an hour.


Thank you so much JSeery

JSeery 04-08-2015 11:44 AM

Re: Oil pan 59AB photos
 

4 Attachment(s)
I'm easily distracted! But here are 4 shots of 59a block. This is a 48 block (as far as I know) out of a Truck.


All times are GMT -5. The time now is 02:08 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2020, vBulletin Solutions Inc.