'41 4cyl P/U question
 

Looking for verification that this is a 1941 4 cyl Pickup front cross member. https://uploads.tapatalk-cdn.com/202...efe8881865.jpghttps://uploads.tapatalk-cdn.com/202...dfbf49152d.jpghttps://uploads.tapatalk-cdn.com/202...ea4fa171df.jpghttps://uploads.tapatalk-cdn.com/202...b23e1b5b4e.jpg

Sent from my E6910 using Tapatalk

Re: '41 4cyl P/U question
 

what you have is a 6 cylinder cross member for a 1941 1/2 ton pick up. I have owned 2- 1941 4 cylinder pick ups and they use the regular cross member. this cross member came about with the us army request for 6 cylinder engines. after about midyear 1941 they all had the dropped cross member in the big trucks, probably about the same in pick ups

Re: '41 4cyl P/U question
 

Thanks, I had a feeling that it wasn't, but wanted to make sure. I got it with a cache of '40-'41 pickup parts I bought and didn't have much trust in the sellers word.

Sent from my E6910 using Tapatalk

Re: '41 4cyl P/U question
 

It is not 41 pickup, 6 or 8 cylinder. I don't think it is 41 pickup at all. It looks to be a bolt in on a frame that has boxed front rails. Note the upper flanges sticking out. As far as I can tell, that would not fit either of my 41 pickups.

Can't say what it is, but can say what it isn't.

You're not doing yourself any favours by posting the pictures in a very difficult to see orientation.

Re: '41 4cyl P/U question
 

Repost.

Re: '41 4cyl P/U question
 

I've got to agree with "Mart". The pic below shows the end of a '41 "deep" crossmember. DD


https://www.fordbarn.com/forum/attac...3&d=1521149332

Re: '41 4cyl P/U question
 

The early 1941 pickups continued with the frame used the year before. The new crossmember came in the mid year production for the new G-series 226 that was introduced for 1941. The 1941 cars had a different frame that was designed to use either V8 or the G6. The commercial 1/2 ton had to be modified to use either engine so it took a while longer for their production.

The 9N engine use was introduced early but sales were dismal at best so it was likely discontinued before the 6-cylinder change but I have no info to confirm that.

Re: '41 4cyl P/U question
 

rotorwrench, seconds what I said

Re: '41 4cyl P/U question
 

https://www.fordbarn.com/forum/attac...p;d=1618894240

https://www.fordbarn.com/forum/attac...p;d=1618894245

https://www.fordbarn.com/forum/attac...p;d=1618894249
Regarding that "mystery" Ford Pick-up Front Cross Member, these smaller pictures might help in correctly identifying it.

Re: '41 4cyl P/U question
 

I had a hacked off front frame section with a crossmember like that, mine was 46-48 car.

Re: '41 4cyl P/U question
 

26 1/4” width between the frame rails

Re: '41 4cyl P/U question
 

Thanks for the info fellas. Sorry about the orientation Mart, I was having enough difficulty posting with this phone anyway. Thanks for the repost Mercman. I knew it didn't look anything like the one in my '41 V8 half-ton. I was just going off what the fella who sold me the parts said it was, that's why I asked here. Best place I've found to get reliable info. It wasn't why I bought the parts, and since it's probably not anything anyone else would need, it's probably heading to the smelter.

Sent from my E6910 using Tapatalk