A vs AA Transmission
 

This a has been in the family a long time...I recently brought it home from storage at my brothers place.

It had the AA transmission since before we owned it (1962).

In a week and a half I have learned to dislike the AA transmission and would like to replace it with the proper A transmission.

I have no idea what else may have been altered when the AA transmission was installed.

Does this look like a typical A bell housing off a 29 or 30?(it has a 1930 engine)

That's about 7 1/2" across the bellhousing casting where the transmission bolts up..

What else should I look for?

Randy

Re: A vs AA Transmission
 

The 4-speed bell housing will not work with the 3-speed. What don't
you like about the 4-speed, it should shift like the 3-speed except for
the super low first gear just start in 2nd.

Bob

Re: A vs AA Transmission
 

Hey Randy,
I'm kind of with Bob here, in that, if you start out in second gear that should / would suit better for driving. Then if truck has a load and/or you wish to creep along, you then have the creep first gear!
It must have been 'the thing' to put AA 4 speed trans in the '29 truck. I have an AA 4 speed and an A trans ..BOTH out of '29 ford trucks. Do you have the 'lockout' lever on your shifter stick ? My AA 4 speed has that feature.

Re: A vs AA Transmission
 

Yes I have the lockout.....

First gear is a creeper for sure!

It just does not want to shift into second from a standstill...first and reverse no problem.....Otherwise it shifts fine. It is noisy in all gears...

One thing is I have 140 wt oil in there....the 600w is on order and I will change it out when it arrives.

Maybe i can get used to it..but it just does not seem to be very well installed...the rear mount just sits on top of the crossmember, and the shift tower sticks up higher in the cab....

Re: A vs AA Transmission
 

You have an AA bellhousing. The AA bellhousing is shorter in length and desirable to those who want to do a F150 or T5 transmission conversion. The AA housings are worth $150. to $250. The A bellhousing is what must be used if going back to A 3 speed and is worth less than half as much. If you are interested, I have a A bellhousing and A 3 speed transmission available, . Venders sell a Mitchel transmission which is a stock A 3 speed built with synchronized 2nd and 3rd gears and they offer different gear ratios. A stock A 3 speed core is required to be turned in.

Re: A vs AA Transmission
 

Why does it look like the engine is only sitting on the mounts, not bolted to them? (And has been shimmed up)

just so it is clear....600W is not 600 weght. 600W is the product name. Its weight is somewhere around 175 i think. Like creamy peanut butter left in the sun.

145 will lube but you may have to delay your double clutch a bit as the gears wont slow down as fast.

Re: A vs AA Transmission
 

From the second picture, the bell housing is not even bolted to the rear engine mount. A bit of work is in order, but it is usually that way after eighty plus years!

Re: A vs AA Transmission
 

This old truck has so many things missing or poorly installed or broken...86 years of hard use and minimal maintenance..

And yes...the bell housing is only bolted to the mount on the left side....the right side is what you see....

unfortunately it looks like the bolts have been broken off flush with the bell housing surface...

I have ordered new motor mount rubber pads and bolts, and maybe just maybe I can get what's left of the bellhousing bolts out.

Does that rear transmission mount sitting on the crossmember look normal for an AA conversion?

Let me see how the 600w oil works for me..and a local owner mentioned that since it had been sitting so long the flywheel face and pressure plate may have some corrosion. When I was in high school we used to drive this truck around..i don't remember it being so difficult to get into second from a stop....but I'm pretty sure my brother put 90wt gear oil in it since then....

I got a ride in a local owner's beautiful 29 Fordor....it's the only other model A I've ever been in! What a treat!

Re: A vs AA Transmission
 

If the pin in the top of the transmission tower is worn it can make
it hard to get into some gears, look at the video Fullraceflathead made
on repairing this. https://www.youtube.com/playlist?lis...E4m50cDoDpBOJh
It also help to let the clutch out just a little to get the gears to mesh.

Bob

Re: A vs AA Transmission
 

Bobc, it sounds like his clutch may be dragging so the gears are grinding when he tries for second. Since first is a low, low gear, it's turning slow enough that it can be slipped into first even though the gears are still turning.
Might try putting into second before starting the engine, and then downshifting as you come to a stop so you're in second at the stop sign, ready to go without any grinding!

Re: A vs AA Transmission
 

Hey Randy,
Wow, if that situation is only half bolted in, no wonder you are having trouble with it !
There must be a ton of unnecessary stress put on the entire driveline when torque is applied...if not lined up and bolted down as per original. Wonder something hasn't busted...or maybe it has.
The 140 wt is good for your trans/rear.
I'd first try to get it all checked out for damage/cracks, then bolted down properly and adjust clutch. It sounds amazing that you can shift it at all what with the different stresses being unsecured will cause.

Re: A vs AA Transmission
 

I'm going to do my best to set it right...

I was wondering if maybe the rear transmission mount sitting on top of that crossmemeber wasn't forcing the front of the engine to be too low..the front engine mount looks a little low, but i have nothing to gauge it by...i don't have a hand crank but a socket extension seems to line up with the crank hole OK....

The brake cross tube does not touch the transmission, but it's pretty close...I was able to get the speedo drive gear off to check it and remove the mangled speedo cable...

Lots of issues here for sure.....

Re: A vs AA Transmission
 

I watched Fullraceflathead's video as posted above....My shift lever is pretty loose, 3" sided to side measured at the shift lever just under the knob...and there is some rotational movement also..

I guess I better put that on the list

Re: A vs AA Transmission
 

My 1928 Roadster Pickup has the 4 Speed AA Transmission in it.
Mine does not have a rear mount at all. The mounts are on both sides of the Engine and the one at the front of the Engine.
The bracket you have on your Transmission looks like it is not original.

Re: A vs AA Transmission
 

Thanks for that.....when I get the rear motor mounts repaired I'll see how tough it is to get that mount off...

Today I took the shift lever out. Mine has the screw-on cap and only one locating pin.

The pin looked OK and was a snug fit in the tower, but as you can see the lever ball is pretty well worn. And down inside the shift rails are also pretty worn....a little here and a little there, and soon it's just plain loose!

I also replaced the manifold gasket, studs, washers and nuts (it had bolts with regular flat washers), fuel shutoff valve and the carb bowl gasket. I'm hopeful there will be no more seeping fuel. I also set the float level up a bit..1 3/32" measured from the gasket flange to the top of the float...

Re: A vs AA Transmission
 

Yes the slot area is very worn. Mine was almost the same. I made my pin oversize in diameter and a little longer so it went into the unworn area of the slot.
The Pin is available but to really fix the slop issues I would have the worn areas of the slot welded up. It doesn't take much of a weld bead to build up the worn areas.
Your AA is the later version with the threaded shifter cap, that's a good thing. The caps are available new old stock. They don't wear much though.
Be very careful that pin doesn't drop into the transmission. If it does you'll have to either use a magnet to retrieve it or remove the PTO cover and get it out, unless your lucky enough to have it pass out the drain plug hole while draining the oil.
The pin was missing in mine and some one used a stove bolt in it's place. It had so much slop I could move the shifter 7" or more in all directions even when it was in gear.

Re: A vs AA Transmission
 

I have a mig welder...it's 120v but it ought to do the trick....but there are other fish to fry first..

Also the tension spring on the shift lever was almost flat, nearly just a spacer...

Re: A vs AA Transmission
 

I gave the mounting bracket a closer look and I see that it is just welded to the u-joint housing.....

They needed it for a reason.....more will be revealed....

Re: A vs AA Transmission
 

Let me take a few photos of mine so you can see how mine is set up.

Re: A vs AA Transmission
 

The bearing retainer on the back of your transmission looks
like for a 32 or maybe later.

Bob