|
Help!!! Mallory Zb distributor housing weld repair 3 Attachment(s)
Hey guys, Today I made an attempt to disassemble and clean my Mallory ZB distributor.
I was able remove the breaker plate and counter weights and thats it. I got stuck at removing the pin on the distributor drive gear. While I was trying to punch out the pin , the distributor was wrapped in a rag on a bench vise. I removed it from the vise to change the plan of attack when I noticed the case broken. 😮www.jalopyjournal.net💨 Can this be welded or brazed? |
Re: Help!!! Mallory Zb distributor housing weld repair Quote:
https://www.fordbarn.com/forum/attac...9&d=1776199949 https://www.fordbarn.com/forum/attac...0&d=1776199949 |
Re: Help!!! Mallory Zb distributor housing weld repair D. F. W. I. !!!
|
Re: Help!!! Mallory Zb distributor housing weld repair I doubt if it can be saved. Don’t let anyone fool you, too many variables.
I would suggest you hang it on the wall and show it off as a learning tool/what not to do. I can't imagine anyone grabbing onto the body of an aluminum distributor and trying to drive a roll pin out of the shaft and gear. Lot of help on this board, just ask. I usually find a scrap piece of 2x4 and cut a 45 ° grove. I place it UNDER the gear and drive the roll pin out |
Re: Help!!! Mallory Zb distributor housing weld repair Do a search for someone in your area that does high tech welding repairs. Assuming that the distributor body is aluminum, there is a new laser welding process on the market today that might mean it could be repaired in the hands of a pro. Depending on what value you put on the Mallory, it might be too expensive to repair it, but I'm not sure what the cost would be. The laser welding process is more sophisticated and less invasive and produces less unwanted heat from what I'm hearing. Could be worth investigating.
|
Re: Help!!! Mallory Zb distributor housing weld repair Laser welding is your solution if you cannot machine it. If you have a lathe you could turn the diameter down and make shrink fit replacement.
|
Re: Help!!! Mallory Zb distributor housing weld repair The housing is cast aluminum it can be repaired by a competent tig welded with a little bit of work. In the location of the break thankfully there's no bushings its just an open tube.
The repair is simple first you "V" the edges of the break this gives depth to where the weld is located. You then use a steel shaft the same diameter as the upper and lower bushing diameters placed in the bushings as the alignment fixture. If a shaft is not available the shaft from the distributer can be used as the alignment fixture. The tig welding is done a little at a time spot welding at three equal locations first so there's minimal alignment distortion. Then gradually the welding continues between the three spots until the entire area is now welded. Once the entire area is welded the bead of thew weld can be removed using a lath or carful hand filing. Ronnieroadster |
Re: Help!!! Mallory Zb distributor housing weld repair It would need new bushings installed and reamed too, right guys?
|
Re: Help!!! Mallory Zb distributor housing weld repair Maybe not if the repair is done by a skilled welder.
|
Re: Help!!! Mallory Zb distributor housing weld repair 8 Attachment(s)
UPDATE PROGRESS REPORT:
I was able to get a coworker seasoned welder to do the repair.! Looks pretty good as far as the weld and structure. I found a piece of round stock that fit perfectly snug in the I.D. Of the case, and used it to keep the stem true and straight. Worked out great. Now for the Weld, I'm going to wait on grinding down the weld until I'm ready to install. I don't want to remove too much material and grind away the weld. I want to see if I can clear off just enough to fit in the bore trying not to compromise the weld . Now the next order of business is removing the stuck Vacuum Brake plung0er |
Re: Help!!! Mallory Zb distributor housing weld repair Nice !!! Glad you could save it. I had one a few years back & couldn't find points 4 it so went back to stock setup.
|
Re: Help!!! Mallory Zb distributor housing weld repair That looks like a good repair. When you consider that the distributors with the extended lower shaft have a much shorter upper support surface, that should be more the enough.
Mike : The points for these (Mallory # 24875B, I believe) show up on eBay all the time. In addition, I have found an equivalent Echlin set from NAPA that will substitute in a pinch. In the alternative, I will take the distributor off your hands for a good price (if you still have it). |
Re: Help!!! Mallory Zb distributor housing weld repair Quote:
|
Re: Help!!! Mallory Zb distributor housing weld repair Congratulations Just as I wrote above a simple fix when the person welding the cracked area correctly knows what they are doing.
Ronnieroadster |
Re: Help!!! Mallory Zb distributor housing weld repair This is good news!
|
Re: Help!!! Mallory Zb distributor housing weld repair If they V-ed out the break area (which I'm sure they did), then you should chuck the housing in a lathe and accurately remove the extra weld material.
|
Re: Help!!! Mallory Zb distributor housing weld repair Quote:
|
Re: Help!!! Mallory Zb distributor housing weld repair "Quote:
Originally Posted by Bored&Stroked View Post If they V-ed out the break area (which I'm sure they did), then you should chuck the housing in a lathe and accurately remove the extra weld material. This. I would try to remove this way vs. grinding it away" I don't understand the need for this grinding/cutting. The housing is mounted statically. As long as the weld doesn't interfere with installation, I'd leave it alone. |
Re: Help!!! Mallory Zb distributor housing weld repair Quote:
|
Re: Help!!! Mallory Zb distributor housing weld repair The other thing the lathe gives you is the ability to put a dial-indicator and check to see if the end bushing bore is in alignment with the housing OD.
In almost all cases (even with proper setup) welding distorts/moves things. You may need to over-bore the end bushing in the housing and make a new custom bushing to ensure the bushings are running true to the same center axis. |
Re: Help!!! Mallory Zb distributor housing weld repair Quote:
|
Re: Help!!! Mallory Zb distributor housing weld repair Thanks guys for the suggestions, I'll talk to a machinist here at work and ask if they can turn it down for me.
When I was talking of grinding I didn't think on a lathe, and I just wasn't sure if the bore on the timing gear cover is tapered or straight. Let me find a machinist I can become friends with, then I'll update after that with "true' readings of the casing and reassemble |
Re: Help!!! Mallory Zb distributor housing weld repair Variables I mentioned
In almost all cases (even with proper setup) welding distorts/moves things. You may need to over-bore the end bushing in the housing and make a new custom bushing to ensure the bushings are running true to the same center axis. The other thing I would do is inspect the weld on the inside. If your weldor did not “push” the bead thru you will see a line. That is the beginning of a flaw/weak spot. IF you intend on using it I WOULD NOT mill/grind down the reinforcement for appearance sake. |
Re: Help!!! Mallory Zb distributor housing weld repair Yeah, I was thinking too, that weld looks good on there. I'd sure leave it.
|
| All times are GMT -5. The time now is 01:25 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2026, vBulletin Solutions Inc.