1940-41 Ford pickup wooden cab mounts.
 

Hello all. I’m working on a 40 Ford pickup. I was wondering if anyone had drawings or measurements for the wooden cab mounts. I’ve seen lots on the web to buy, but since I’m this far in, I would prefer to make my own. I believe the only years are 40-41 that will work. Thanks.

Re: 1940-41 Ford pickup wooden cab mounts.
 

FWIW, Ford made a floor design change sometime between the first 1938 and the last 1939. The 1940-41 blocks are the same as the later style.


Functionally, you likely do not need the full timber block Ford used. A short (about 4" front to back) spacer for the #2 and # 3 body bolts with a spacer covering between the # 4 body mount and front bed mount (the front bed mount timbers stack onto a "tail" of the body block" should do the job. Note the #1 cab bolt is direct to frame (except for a single layer of webbing).

Re: 1940-41 Ford pickup wooden cab mounts.
 

Thanks for the information Karl. I would prefer to make it as original as possible. So the ford ones would be my preference. I’ll keep looking

Steve

Re: 1940-41 Ford pickup wooden cab mounts.
 

I would like to see the dimensions for the box wood mounts as well, if you come across anything be sure to post it on here.

Kirk

Re: 1940-41 Ford pickup wooden cab mounts.
 

I have photos, but no dimensions.

Re: 1940-41 Ford pickup wooden cab mounts.
 

Re: 1940-41 Ford pickup wooden cab mounts.
 

I finally made some with my father in law.

Re: 1940-41 Ford pickup wooden cab mounts.
 

Nice!


btw, what is your father in law doing for legs now?

Re: 1940-41 Ford pickup wooden cab mounts.
 

Thanks Karl, made me laugh. Those do look very nicely done.

Re: 1940-41 Ford pickup wooden cab mounts.
 

i still make the right wood blocks with finger joints in ash although the oringnal were hard maple . ihave sold very many over the years . we were the first ones to make them correcty there is a tail piece missing in your picture

Re: 1940-41 Ford pickup wooden cab mounts.
 

Yes, the cab mount also is the loer part of the bed front mounts. Tim

Re: 1940-41 Ford pickup wooden cab mounts.
 

I was just going to say, that the pickup cab wood should have an extended piece that goes under the first wooden cross member of the box.

You can see it in these pictures I found on the internet.

I don't have pieces like this. Bob Drake no longer sells them.

Kirk

Re: 1940-41 Ford pickup wooden cab mounts.
 

Nice job, Weirdo. I made some too, based on some originals. Yours came out much better than mine. My originals and my copies also do not have the tails.

https://www.fordbarn.com/forum/attac...3&d=1736087728

Re: 1940-41 Ford pickup wooden cab mounts.
 

I’ll have to go look at the rear of the truck. It’s still on the old frame.i knew there was a couple pieces left, but miss that tail. Should be a lot easier than the others

Re: 1940-41 Ford pickup wooden cab mounts.
 

For reference these are the original "long" blocks that were under my '38 cab. They measure 61-1/2" long.

Re: 1940-41 Ford pickup wooden cab mounts.
 

Bill, your blocks illustrate the "tail" perfectly. Note the differences between the 1938 blocks and the 1940-41 blocks where they fit the cab. This is due to the first 1938 carrying over the 1935-37 cab floor, and the redesign of the floor sometime before the last 1939.

Re: 1940-41 Ford pickup wooden cab mounts.
 

I guess the real question is since only the trucks have cab wood, why is it that all the wood kits are incorrect and missing the tail piece?

Re: 1940-41 Ford pickup wooden cab mounts.
 

The good "expensive" repro's will have the tails. The "el cheapo" may not. Note that the OP had made his own in an admirable effort as these are not easy parts to make. I suspect the OP's will end up growing tails.

Re: 1940-41 Ford pickup wooden cab mounts.
 

What I would like to see made are mounting blocks for the later 42-47 cabs on a 35-41 truck frames. Just a thought as I had yo jump through some hoops when buikding my wife’s truck …. the 43-47 cab was placed on a 36 frame ….

Re: 1940-41 Ford pickup wooden cab mounts.
 

Yep the OP did a nice job on his wood, sadly I have zero wood skills!
There aren't many sources for truck wood at this point. Bob Drake at one point had all the pieces for the pickup, including cab wood, box cross pieces and all the long bolts etc. However now they carry nothing at all.

Kirk

Re: 1940-41 Ford pickup wooden cab mounts.
 

Note that if you search the Ford Barn for the thread "40-41 pickup bed" there is info and dimensions on the 38-41 pickup box blocks.

Re: 1940-41 Ford pickup wooden cab mounts.
 

I found one. I left the back part of the truck on the old frame. Part B. There didn’t appear to be a finger Joint, for that piece. Can anyone tell me if they were just butted together? Attachment 558898

Re: 1940-41 Ford pickup wooden cab mounts.
 

I would like a price on a set for a 40 and also 1936