Installing a Mitchell Overdrive
 

I am planning on installing a Mitchell Overdrive in the future. Are there any other parts people recommend replacing at the time of installation that are not included with the overdrive?? It is not very easy or fast for me to get Model A parts where I live, so I want to make sure I have everything ready when I get around to doing the installation. Any recommendations appreciated. Thanks

Re: Installing a Mitchell Overdrive
 

make sure you have a u-joint gasket kit.... and your U-joint is good... and of course if your rear axle needs rebuilding at the same time that it is done. If it is good then great. I would never put a Mitchell in a rear axle that has NOT been rebuilt properly.

Of course brakes should also be paramount and up to snuff. Other than that Mitchell supplies everything for the conversion in their package. They have it honed down well and I can promise you will be pleased. It makes it a new car ( or truck).
Larry Shepard

Re: Installing a Mitchell Overdrive
 

Larry, I recently upgraded the brakes, new cast iron drums, brake shoes, Ted's floater kit etc

I also recently did the rear axle when I installed a new gear set (3.54:1). I have a freshly built touring engine with HC head, counterbalanced crank etc so I am confident the 26% over drive and 3.54:1 gears should work well from what I have read on here.

I might grab a new u-joint just in-case. Thanks for the response. Any other suggestions??

Re: Installing a Mitchell Overdrive
 

Pinion gear puller ...

Mitchell used to rent them.

Re: Installing a Mitchell Overdrive
 

Mitchell has re-designed their pinion puller and now sell them fairly reasonable. Absolutely worth having.

Re: Installing a Mitchell Overdrive
 

tall jack stands to get the rear end up in the air.
Bob

Re: Installing a Mitchell Overdrive
 

For reasons of safety you should acquire and use a proper spring spreader.

Tom Endy

Re: Installing a Mitchell Overdrive
 

I am an amateur mechanic, and have installed two Mitchell Overdrive's (and man, do I love them, but that's another story).

An obvious thing to replace would be the clutch disk, but that requires removing the transmission, the bell housing, and the pressure plate, none of which are necessary for installing the overdrive (you're just near that working area when doing so).

You may wish to replace the main speedometer cable, in case your original is rough or worn.

For the first Mitchell I installed, I fashioned a pinion puller from a small, thick piece of sheet metal, and damaged the pinion bearing cup doing so. The second time I used a pinion puller tool I bought from Snyder's (made by Mitchell, I believe), and everything went much more smoothly and quickly. This is a ~$80 investment I recommend.

Beyond that, to quote 'Yes, Prime Minister,' "There are many things you can do, but nothing else you must do. You're the boss!"

Re: Installing a Mitchell Overdrive
 

I have both a pinion puller I bought from Snyder's and one I bought from Mitchell. The one from Mitchell is heftier than the one from Snyder's.

Having said that, whatever works for you. The price is about the same for either tool.

Re: Installing a Mitchell Overdrive
 

Thanks to everyone for the input.

Re: Installing a Mitchell Overdrive
 

The snyder pinion puller I got from Snyders was not strong enough to pull the pinion. I had to drill and tap 3 more holes for three more bolts to keep from bending the tool.

Re: Installing a Mitchell Overdrive
 

I recently installed a Mitchell Overdrive. The universal Gasket set and gasket for pinion end came in the box with my overdrive. You don't get the actual universal joint.

Re: Installing a Mitchell Overdrive
 

http://www.snydersantiqueauto.com/pi...tallation-tool

I think I might grab the one above. Appears to be better than the one below.

I am guessing the one below is the one people have said is not up to the task.

http://www.snydersantiqueauto.com/pinion-puller

Re: Installing a Mitchell Overdrive
 

Install kit that comes with the overdrive includes a speedometer cable.
The more elaborate pinion puller looks like the mitchell I have.
You might ask about the correct mount for your pickup the clearance from the top of the shift arm casting has to clear the floorboard. Mitchell has a modified casting.
Bob

Re: Installing a Mitchell Overdrive
 

Bob, thanks for the info on the shift arm casting.

Re: Installing a Mitchell Overdrive
 

Mitchell is just 4 hours north of me, so it was easy to exchange the mounting.
Bob

Re: Installing a Mitchell Overdrive
 

Waxhead

You are correct. The second one in your post is not up to the task.

Re: Installing a Mitchell Overdrive
 

I also just installed a Mitchell overdrive in my 31 Tudor. I built a rolling mount with two connected dollies to support the rear axel and the front of the torque tube. There are several versions I have seen. This dollie makes the installation much easier.

Also you need two thin wrenches to set the preload of the pinion bearing.
Snyders part # A-4634-T

Regards,

Stew

Re: Installing a Mitchell Overdrive
 

you might want a rubber bellows to slip over your new shift lever

Re: Installing a Mitchell Overdrive
 

You might consider replacing your rear bushes when you detach the spring. Mine were worn and I had to destroy one of them to remove it.
X2 on all the comments on getting the sturdiest puller you can. The Snyder one that I borrowed bent during the process.
Enjoy your Mitchell. You'll join the "Aah!" Club the first time you slip it into overdrive! Overdrive 2nd is also a great ratio.

Re: Installing a Mitchell Overdrive
 

Pray it does not leak out all the oil you put in the box at the joint between gearbox and rear torque tube as the last two I installed did. Silicone gasket maker sealant can be 100% effective if used correctly however they do not seem to know how to use it.

Re: Installing a Mitchell Overdrive
 

Thanks to everyone for the great advice and suggestions. I have no doubt that it will assist in making the install easier. Just need to wait the 3 months for delivery of the OD :)

Re: Installing a Mitchell Overdrive
 

3 month back-up? Hang in there!

Glenn

Re: Installing a Mitchell Overdrive
 

Is it necessary to remove the springs, and is it easier to install Mitchell with it removed from chassis?

Re: Installing a Mitchell Overdrive
 

You would have to remove the rear end to remove the driveshaft.

Re: Installing a Mitchell Overdrive
 

The Mitchell is much easier to install if you remove the rear end from the chassis. It would be very difficult working under the car if you don't.
Good Day!

Re: Installing a Mitchell Overdrive
 

how many man hours to install a mitchell overdrive?

Re: Installing a Mitchell Overdrive
 

Depends.
Talk to mitchell.
Bob

Re: Installing a Mitchell Overdrive
 

Re: Installing a Mitchell Overdrive
 

A little tip when installing a Mitchell overdrive:

The boss where the speedo gear head inserts in the housing is below the oil level in the housing. For this reason do not oil service it until the speedo head is installed. The set screw that holds the speedo head in place will drip oil unless you coat it with some type of sealer before installing.

Tom Endy

Re: Installing a Mitchell Overdrive
 

I just finished installing both a Mitchell Overdrive and transmission in my 1929 model A roadster P/U. Also bought their puller kit which worked great. It was quite a bit of work......however, I love the way the Mitchell transmission shifts. No problem with gears grinding now......wonderful when down shifting.

The overdrive shifts fairly easy but stiff. Goes in to over drive easy but does not shift easily back it to direct drive. Some times I must stop in order to shift back in to direct drive. Slot in floor board has good clearance in both directions. Other than adjusting the shaft length that connects the shift lever to the overdrive......I do not see any other adjustments. Was told the overdrive has syncro's which should allow shifting in and out of overdrive while driving. I have been pushing in the clutch when shifting in/out of overdrive.

Any suggestions?

Les Von Nordheim

Re: Installing a Mitchell Overdrive
 

I would give Mitchell a call...The units usually shift very easily...How does it shift if you are standing still and the engine is not running? Also try shifting it from under the car with the linkage disconnected and see if it makes a difference...It is possible that you have a linkage problem and not an overdrive problem...Ernie in Arizona

Re: Installing a Mitchell Overdrive
 

Give it a chance to warm up. I asked Sue and Steve Mitchell at the MAFCA Convention this year about the problem shifting when cold, they told me to give it a chance to warm up.
When they delivered mine I was told to use 85w-140 GL-5. That seems too thick to me but when it's warmed up after a mile or two, it's just fine, never grinds. I would suggest changing your gear oil in it soon after it's first installed, and after that every 5,000 miles. Don't forget to pull the plugs in the torque tube one in front of the overdrive and the other behind the overdrive box and give it no more than a couple pumps when you change the oil. One of the fittings they give you is close clearance, make sure your rear axle is up on jack stands and park brake released so you can turn the driveshaft to access the grease fittings. I have good results with Ultra Black sealant between the torque tube and differential and a dab of ultra black on the set screw holding the speedometer drive. Tie up the breather tube as high as possible. I have absolutely no leaks.

Re: Installing a Mitchell Overdrive
 

My overdrive shift smooth as silk both up and down

Sent from my SM-J700T using Tapatalk

Re: Installing a Mitchell Overdrive
 

Get the best spring spreader you can and leave the spring together with the differential.
Get the best of the two pinion pullers discussed above. I have used both. The good one works, the other one bends. It takes about four hours and is a bit quicker with someone helping you. Two rolling floor jacks are what I use and have done them alone several times, much easier with two guys. Not rocket science, just heavy and I'm not as strong as I was 60 years ago. Be SAFE. I tip the torque tube up and slide the Mitchell down onto the differential. The spring and spring spreader help hold the torque tube up if working alone. This part and aligning the splines with the U-joint are easier with help. The rest is just screwing in nuts and bolts, or unscrewing them. The pinion adjustment is quite simple, I go where I think it is too tight and back it off a tad. I have been told that inch-pound torque wrenches are notoriously inaccurate so I just get the feel of some drag on the pinion and have been happy with those results. Your experience may very.

Re: Installing a Mitchell Overdrive
 

A tip based on my experience with the Mitchell....
After the new unit is installed you need to pin up the OD vent tube.
It's very important this tube always be in a incline from the OD unit.
If you let any part of the vent tube sag small amount of oil will
Start holding in the sag. On hard pulls the tube just may "burp"
This oil out the end of the tube. And if the end of the tube is located
Near/above the muffler.... instant smoke screen!
I know!
Locating this vent tube on the Vicky with the drop floor
And keeping it in a inclined position can be challenging... be done for sure.
Love the Mitchell.
Gil. NoCal

Re: Installing a Mitchell Overdrive
 

Thanks for the guidance.

I will make a shifting linkage adjustment and see if that helps. Also, I may have not had the overdrive heated up......will do more driving and see if shifting when warmed up is easier.
I'm using synthetic gear oil supplied from McMaster Carr 90/140. Also us it in the mitchell transmission. Have used this specific gear oil in my other antique cars with good results. Does not eat up bronze or brass like some other conventional gear oils.
I have the breather tube attached under the P/U bed (High) with a loop clamp.

Just joined the Model A club of america but have not joined a regional group....have several in our area. Have been a member of the HCCA and Model T ford club of america for many years. Enjoy driving and owning a Model A.

Thanks,
Les