Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 09-13-2010, 08:45 PM   #1
Bill Lee/Virginia
Senior Member
 
Join Date: May 2010
Posts: 295
Default Adjusting Model "A" Valves

I need to adjust the valves on my Model "A". Where can I find detailed instructions to do this? Thanks.
Bill Lee/Virginia Peninsula
Bill Lee/Virginia is offline   Reply With Quote
Old 09-13-2010, 09:17 PM   #2
Mitch//pa
BANNED
 
Join Date: May 2010
Location: Bucks County, PA
Posts: 11,454
Default Re: Adjusting Model "A" Valves

http://www.fordgarage.com/pages/ruleofnine.htm

Last edited by Mitch//pa; 12-02-2010 at 12:49 PM.
Mitch//pa is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 09-13-2010, 09:23 PM   #3
J Franklin
Senior Member
 
J Franklin's Avatar
 
Join Date: May 2010
Location: Oregon
Posts: 5,947
Default Re: Adjusting Model "A" Valves

If your car is equipped with Model A Ford tappets you will need the previous instructions to find the heel of the lobe, but you will adjust the valves by grinding either the face or heel of the valve depending on the direction you will need to adjust.
J Franklin is offline   Reply With Quote
Old 09-13-2010, 11:39 PM   #4
Richard in Anaheim CA
Senior Member
 
Richard in Anaheim CA's Avatar
 
Join Date: May 2010
Location: Anaheim California
Posts: 551
Default Re: Adjusting Model "A" Valves

If you have adjustable lifters, the best method is the "9" method.

Number valves from front to back 1 through 8.

It is fairly easy to determine when a valve is at the top of it's lift. When you have reached that position on #1 valve you adjust the corresponding valve to equal "9". In this case it's #8 valve.

Continue with 2&7, 3&6, 4&5, 5&4, 6&3, 7&2 and finallly 8&1.

If you use different clearances for intake and exhaust, you need to pay attention. I put a piece of masking tape along the bottom of the ports and mark the settings there and cross them off as I finish.

Good Luck

Richard
Anaheim,CA
Richard in Anaheim CA is offline   Reply With Quote
Old 09-14-2010, 08:18 AM   #5
Bruce
Senior Member
 
Bruce's Avatar
 
Join Date: May 2010
Location: Sun City West, AZ
Posts: 489
Default Re: Adjusting Model "A" Valves

I've adjusted valves on our Open Pickup but have the tough part to go. The truck's tappets are adjustable but have the double nut locking setup. The block has not been machined to make holding the tappet/locking down the nut a simple task. In fact, I think I will have to grind a 1/2" tappet wrench down to the thickness of a dime to geterdone.
Any tricksy methods to make this easier? Gotta finish the job to get back on the road in time for Fox Valley's Model A Day drive to Starved Rock State Park on Saturday.
Bruce is offline   Reply With Quote
Old 09-14-2010, 08:23 AM   #6
roadster
Senior Member
 
roadster's Avatar
 
Join Date: May 2010
Location: Severn,Maryland
Posts: 132
Default Re: Adjusting Model "A" Valves

Sponsored Links (Register now to hide all advertisements)
I have a friend that has a valve tap but does not have adj. valves
what can he do?
roadster is offline   Reply With Quote
Old 09-14-2010, 09:25 AM   #7
Frank Miller
Senior Member
 
Frank Miller's Avatar
 
Join Date: May 2010
Location: Auburn, MA
Posts: 2,106
Default Re: Adjusting Model "A" Valves

Roadster he will need to grind the valves. A slight tick is not a big problem. As a matter of fact when you cannot hear them they may be set too tight causing them to burn prematurely due to not having enough time on the seat to cool properly.
Frank Miller is offline   Reply With Quote
Old 09-14-2010, 10:57 AM   #8
Russ/40
Senior Member
 
Russ/40's Avatar
 
Join Date: May 2010
Location: Santee, California
Posts: 3,505
Default Re: Adjusting Model "A" Valves

Quote:
Originally Posted by Bruce View Post
I've adjusted valves on our Open Pickup but have the tough part to go. The truck's tappets are adjustable but have the double nut locking setup. The block has not been machined to make holding the tappet/locking down the nut a simple task. In fact, I think I will have to grind a 1/2" tappet wrench down to the thickness of a dime to geterdone.
Any tricksy methods to make this easier? Gotta finish the job to get back on the road in time for Fox Valley's Model A Day drive to Starved Rock State Park on Saturday.
I feel your pain. It's especially bad with reground cams with a small base circle. I had to rotate the cam to a minor lift to get at them and back to the heel to measure. Lots of turning, but it gets it done.
Russ/40 is offline   Reply With Quote
Old 09-14-2010, 03:49 PM   #9
Art Bjornestad
Senior Member
 
Art Bjornestad's Avatar
 
Join Date: May 2010
Location: Westlake Village, CA
Posts: 477
Default Re: Adjusting Model "A" Valves

There is a way to know just how many thousands to turn the tappet by figuring how many thousands a complete turn of the adjusting screw makes and then working out how much an 1/8th of a turn adds to the measurement. A quarter/20 nut does 20 revolutions in one inch of travel so 1 turn of the nut travels 50 thousands, an 1/8 turn just over 6 thousands. figure out what adjustment you need, make the adjustment at the bottom of the tappet travel and it should be spot on. You can do a 16th rev if you take a little time and get a 3 thou adjustment.
Art Bjornestad is offline   Reply With Quote
Old 09-14-2010, 04:37 PM   #10
Bruce of MN
Senior Member
 
Bruce of MN's Avatar
 
Join Date: May 2010
Location: VA
Posts: 1,394
Default Re: Adjusting Model "A" Valves

The .007" per hex flat is mentioned in the link in post #2 above.
Bruce of MN is offline   Reply With Quote
Old 09-14-2010, 06:26 PM   #11
Art Bjornestad
Senior Member
 
Art Bjornestad's Avatar
 
Join Date: May 2010
Location: Westlake Village, CA
Posts: 477
Default Re: Adjusting Model "A" Valves

I was never very good at math but I think that a hex flat will equal .083". I guess I need to find my caliper and see just what it comes out to.
Art Bjornestad is offline   Reply With Quote
Old 09-14-2010, 06:28 PM   #12
Art Bjornestad
Senior Member
 
Art Bjornestad's Avatar
 
Join Date: May 2010
Location: Westlake Village, CA
Posts: 477
Default Re: Adjusting Model "A" Valves

I assumed that the tappet thread was 1/4 20. I just read Vince's site and see the thread is 24 TPI. My bad.
Art Bjornestad is offline   Reply With Quote
Old 09-14-2010, 06:33 PM   #13
Bob Johnson
Senior Member
 
Bob Johnson's Avatar
 
Join Date: May 2010
Location: California
Posts: 977
Default Re: Adjusting Model "A" Valves

Click here for my video page. There is one on valve adjustment.

Bob
Bob Johnson is offline   Reply With Quote
Old 09-14-2010, 10:12 PM   #14
Bruce of MN
Senior Member
 
Bruce of MN's Avatar
 
Join Date: May 2010
Location: VA
Posts: 1,394
Default Re: Adjusting Model "A" Valves

Bob, your method is pretty much what I did, except I eyeball the portions of the .007 per flat of the adjuster for intermediate readings. I am not looking forward to doing it with the motor in the car with the manifolds in place.
Bruce of MN is offline   Reply With Quote
Old 09-14-2010, 11:45 PM   #15
PC/SR
Senior Member
 
Join Date: May 2010
Location: Santa Rosa, CA
Posts: 1,276
Default Re: Adjusting Model "A" Valves

If the head is off, you can get real close by using a dial gauge to measure valve lift. It should be lobe height minus lifter clearance at the top of the lift. Works real good when reassemblying the engine before putting on the valve springs.
PC/SR is offline   Reply With Quote
Old 09-17-2010, 11:19 PM   #16
Bill Lee/Virginia
Senior Member
 
Join Date: May 2010
Posts: 295
Default Re: Adjusting Model "A" Valves

Many thanks to everyone for the info and advice. I will tackle the valve adj task next week and let you know the results.
Bill Lee/Virginia Peninsula
Bill Lee/Virginia is offline   Reply With Quote
Old 10-31-2010, 08:23 PM   #17
Dave in Denver
Member
 
Join Date: May 2010
Posts: 67
Default Re: Adjusting Model "A" Valves

What is the typical recommended valve clearance for the exhaust and intake valves in a Model A Ford Engine?

Thanks
Dave in Denver is offline   Reply With Quote
Old 10-31-2010, 08:25 PM   #18
Dave in Denver
Member
 
Join Date: May 2010
Posts: 67
Default Re: Adjusting Model "A" Valves

In looking at the lifters while the side engine cover has been removed, I see a bolt that the valve rest on that screws intot he lifter. I do not see a nut on this bolt to lock the bolt once adjusted. Is this normal? will the pressure from the valve spring keep the bolt located hwere it is adjusted to?

Thanks
Dave in Denver is offline   Reply With Quote
Old 02-04-2011, 03:50 PM   #19
Kirby1374
Senior Member
 
Kirby1374's Avatar
 
Join Date: May 2010
Location: Coquille, Or
Posts: 280
Default Re: Adjusting Model "A" Valves

I'm about to grind my valves and re adjust the tappets. This has been very helpful
Kirby1374 is offline   Reply With Quote
Old 02-04-2011, 04:47 PM   #20
Special Coupe Frank
Senior Member
 
Special Coupe Frank's Avatar
 
Join Date: May 2010
Location: Northeast Penna
Posts: 2,108
Default Re: Adjusting Model "A" Valves

Quote:
Originally Posted by Dave in Denver View Post
In looking at the lifters while the side engine cover has been removed, I see a bolt that the valve rest on that screws intot he lifter. I do not see a nut on this bolt to lock the bolt once adjusted. Is this normal? will the pressure from the valve spring keep the bolt located hwere it is adjusted to?

Thanks
Sounds like you might have self-locking tappets; where the threaded-part goes into the tappet: are there two flats ground on the tappet so that you can hold it with w wrench while adjusting the hex-head part ?
Special Coupe Frank is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 02:19 PM.