|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
04-30-2024, 11:38 AM | #141 | |
Senior Member
Join Date: May 2015
Posts: 8,212
|
Re: 276 stroker from 35 years of parts
Quote:
__________________
The only thing nice about being imperfect is the joy it brings to others.... "Silver rings, your butt! Them's washers!" "We shot our way out of that town for a dollar's worth of steel holes!" - from 'The Wild Bunch' - 1969 https://www.youtube.com/watch?v=7NReUd2_0u0 |
|
04-30-2024, 11:00 PM | #142 |
Senior Member
Join Date: Jan 2014
Location: Orcas Island Washington
Posts: 4,965
|
Re: 276 stroker from 35 years of parts
Thanks Pete. The threads just plain look better with the big pictures.
__________________
Owner/Operator of 'Jailbar Ranch' on the side of Mt. Pickett. Current stable consists of 1946 1/2 ton pickup turned woodie wagon with FH V8, 1947 Tonner Pickup (red) mostly stock with exception of a cummins 6at turbo diesel, 1946 Tonner Pickup (green) with 226 cu in 6 cyl flathead, 1979 Toyota landcruiser wagon, completely encased in 1947 Ford Jailbar sheet metal. Ok, cornbinder rear fenders..... 'Rusty ol' floorboards, hot on their feet' (Alan Jackson) |
Sponsored Links (Register now to hide all advertisements) |
|
Yesterday, 09:21 PM | #143 |
Senior Member
Join Date: Jan 2014
Location: Orcas Island Washington
Posts: 4,965
|
Re: 276 stroker from 35 years of parts
I now have all the valves installed and adjusted. Everything went well. After I cracked the lifter all the bolt squishing was lighter and at 40 in/lb they adjust firmly and none felt at all loose. I then installed that oil pump gear and am ready to install the crank. I have many questions about oil pans and bellhousings and starter plates. I have multiple cast and stamped BHs and 2 oil pans that look alike with the cleanouts. I also have the 4 bolt die cast seal holders at rear. I overhauled 2 8bas 20 some years ago, just replacing what came off, so there was no need for choosing of parts. I don't have a 'green bible' for the later engines so need help choosing what goes with what. Can I install the crank and then figure out the seals or do I need to set the rear one before the crank? Here's a few pics of what I have. My Best gasket 8ba set doesn't seem to include the rubber for the die cast rear seal holder. Any help appreciated. Thanks, GB
__________________
Owner/Operator of 'Jailbar Ranch' on the side of Mt. Pickett. Current stable consists of 1946 1/2 ton pickup turned woodie wagon with FH V8, 1947 Tonner Pickup (red) mostly stock with exception of a cummins 6at turbo diesel, 1946 Tonner Pickup (green) with 226 cu in 6 cyl flathead, 1979 Toyota landcruiser wagon, completely encased in 1947 Ford Jailbar sheet metal. Ok, cornbinder rear fenders..... 'Rusty ol' floorboards, hot on their feet' (Alan Jackson) |
Today, 01:31 AM | #144 | |
Senior Member
Join Date: May 2015
Posts: 8,212
|
Re: 276 stroker from 35 years of parts
Quote:
__________________
The only thing nice about being imperfect is the joy it brings to others.... "Silver rings, your butt! Them's washers!" "We shot our way out of that town for a dollar's worth of steel holes!" - from 'The Wild Bunch' - 1969 https://www.youtube.com/watch?v=7NReUd2_0u0 |
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|