Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 12-17-2014, 04:30 PM   #1
Brian T
Senior Member
 
Brian T's Avatar
 
Join Date: May 2010
Location: San Diego,Ca
Posts: 1,377
Default Painting Tillotsons

I know some of you will question why, but I will ask anyway, I would like to paint my Tillotson carbs black, I am thinking I will use Rustoleum appliance paint which I believe is an epoxy type paint?.
As they have a smooth surface I need to key the surface for the paint to adhere, they are to complex of a shape to sand on and I did not what to fine media blast them, is there an acid such as Ospho that would etch them enough for this purpose.
I have read that there is no absolute fuel proof paint, the good model airplane paint that did work is outlawed in Cali and maybe else were, also I understand that curing enamel paint is a must and can take a few weeks (not a problem in this case) --- any suggestions appreciated.
Thanks Brian.
__________________
Nothing can be made foolproof, ---- fools are ingenious bastards.
Brian T is offline   Reply With Quote
Old 12-17-2014, 04:45 PM   #2
Fullraceflathead
Senior Member
 
Fullraceflathead's Avatar
 
Join Date: May 2012
Location: Chillicothe, Missouri
Posts: 1,156
Default Re: Painting Tillotsons

If you want to spend a little more money than painting I'd look into having the Tillotson pieces anodized.
Powder coating is tuff but you would have to have the vendor Not paint any interior surfaces, threaded holes etc.
Fullraceflathead is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 12-17-2014, 07:12 PM   #3
Gary Gregory
Senior Member
 
Gary Gregory's Avatar
 
Join Date: Jun 2010
Location: Maryville,Tn
Posts: 302
Default Re: Painting Tillotsons

Dont waste your money...the paint wont stay if the carb leaks...and all my Tillotons weep a little at the bowl gasket or at the drain plug...the paint will peal there first.
Gary Gregory is offline   Reply With Quote
Old 12-17-2014, 08:52 PM   #4
bikejunk
Senior Member
 
Join Date: Oct 2012
Location: beautiful down town Passaic NJ
Posts: 293
Default Re: Painting Tillotsons

most paint their carbs with aero gloss dope u can buy at hobby shop its fuel prof. don't think iv ever seen a tillotson painted .
bikejunk is offline   Reply With Quote
Old 12-17-2014, 09:21 PM   #5
Joe K
Senior Member
 
Joe K's Avatar
 
Join Date: Jul 2010
Location: Cow Hampshire
Posts: 4,173
Default Re: Painting Tillotsons

Lacquer works well. Keep it thin.

MOre detail on this at http://www.rcuniverse.com/forum/rc-f...oof-print.html

Joe K
__________________
Shudda kept the horse.
Joe K is offline   Reply With Quote
Old 12-17-2014, 09:31 PM   #6
Mitch//pa
BANNED
 
Join Date: May 2010
Location: Bucks County, PA
Posts: 11,454
Default Re: Painting Tillotsons

Sponsored Links (Register now to hide all advertisements)
here is what snyders reccomends for carbs
Attached Images
File Type: jpg image.jpg (37.8 KB, 63 views)
Mitch//pa is offline   Reply With Quote
Old 12-17-2014, 09:53 PM   #7
Purdy Swoft
Senior Member
 
Purdy Swoft's Avatar
 
Join Date: May 2010
Location: Alabama
Posts: 8,099
Default Re: Painting Tillotsons

I wouldn't paint a pot metal carb. I have painted Zenith carbs with lacquer and had good results.. NAPA use to sell a product named triple etch that will etch alloys, I'm pretty sure that they still do Rustoleum will probably wash right off with alky-rub gas . Why not try the Snyder lacquer paint that Mitch shows. I have purchaced black lacquer in spray cans at Advance Auto Parts, Auto Zone and sometimes Walmart . Its your project and your choice .
Purdy Swoft is offline   Reply With Quote
Old 12-17-2014, 10:33 PM   #8
w.michael
Senior Member
 
w.michael's Avatar
 
Join Date: May 2010
Location: North Carolina
Posts: 417
Default Re: Painting Tillotsons

I've painted my tillotson many times. Many times. Many times. About once a week for one whole summer. Then I gave up on keeping the thing painted. Every paint I tried wrinkled and peeled off immediately.

W. Michael
w.michael is offline   Reply With Quote
Old 12-17-2014, 11:34 PM   #9
Tom Wesenberg
Senior Member
 
Tom Wesenberg's Avatar
 
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
Default Re: Painting Tillotsons

About 20 years ago I painted a small engine gas tank and let it set and dry for a year. As soon as the corn crap gas hit it the paint lifted and wrinkled. I never had that problem with good gas from the old days.

BTW, it was on the news tonight that the University of Minnesota research department has finally declared corn crap gas is actually worse than real gas. They said the emissions are the same and when you factor in all the energy wasted to produce, refine, and transport the crap, it much worse than just using good gas.

Naturally the ethanol producers disagreed.
Tom Wesenberg is offline   Reply With Quote
Old 12-17-2014, 11:41 PM   #10
Purdy Swoft
Senior Member
 
Purdy Swoft's Avatar
 
Join Date: May 2010
Location: Alabama
Posts: 8,099
Default Re: Painting Tillotsons

Its the alky- rub that causes the problem. Its suppose to help the farmers but it sure doesn't help the old car hobby. anybody that says that it has no effect just doesn't know what they are talking about .
Purdy Swoft is offline   Reply With Quote
Old 12-18-2014, 12:36 AM   #11
dlshady
Senior Member
 
dlshady's Avatar
 
Join Date: Jun 2010
Location: Huntsville, AL
Posts: 538
Default Re: Painting Tillotsons

Quote:
Originally Posted by Tom Wesenberg View Post
About 20 years ago I painted a small engine gas tank and let it set and dry for a year. As soon as the corn crap gas hit it the paint lifted and wrinkled. I never had that problem with good gas from the old days.

BTW, it was on the news tonight that the University of Minnesota research department has finally declared corn crap gas is actually worse than real gas. They said the emissions are the same and when you factor in all the energy wasted to produce, refine, and transport the crap, it much worse than just using good gas.

Naturally the ethanol producers disagreed.

I wonder how many millions of dollars they spent on that study in order to come to the conclusion that we all reached many years ago...
__________________
My latest build thread:
https://fordbarn.com/forum/showthread.php?t=67881
dlshady is offline   Reply With Quote
Old 12-18-2014, 11:19 AM   #12
jhowes
Senior Member
 
Join Date: Jul 2010
Location: upstate NY near Mass border
Posts: 789
Default Re: Painting Tillotsons

I have been runing two tilly's on a duel intake manifold for some time now that I painted blue with rattle can lacquer l They have held up well and do not leak. So it can be done, and they look good.
jhowes is offline   Reply With Quote
Old 12-18-2014, 01:45 PM   #13
Purdy Swoft
Senior Member
 
Purdy Swoft's Avatar
 
Join Date: May 2010
Location: Alabama
Posts: 8,099
Default Re: Painting Tillotsons

Real gas isn't that bad about removing acrylic lacquer. Good tillotson carbs don't leak as badly as Zenith carbs unless the bowl is warped . I bet the dual up draft Tillotsons look cool. I'm running dual B carbs on a couple of mine . I painted mine with spray can lacquer and no problems with the paint .
Purdy Swoft is offline   Reply With Quote
Old 12-18-2014, 02:00 PM   #14
jkeesey
Senior Member
 
jkeesey's Avatar
 
Join Date: Apr 2011
Location: Glenmoore Pa
Posts: 1,644
Default Re: Painting Tillotsons

I always paint mine with good old gloss black lacquer. I prefer the look of a Tilly painted over the pot metal finish. I usually rub the bodies with scotch brite just to give the paint something better to bite to, then wash them in lacquer thinner and blow dry before painting.
jkeesey is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 05:59 AM.