|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
08-17-2013, 09:32 PM | #1 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Model A motor froze-up
Anyone know how to "move" a froze-up motor?
|
08-17-2013, 09:35 PM | #2 |
Senior Member
|
Re: Model A motor froze-up
I have removed the spark plugs and sprayed the cylinders with Kroil, soak, and repeat until lose. Be sure to spray the valves. One can also place a wood dowell dow the spark plug holes and tap, tap, tap. Takes a bit of time and lots of soaking but has worked for me.
|
Sponsored Links (Register now to hide all advertisements) |
|
08-17-2013, 09:48 PM | #3 |
Senior Member
Join Date: May 2010
Location: Bethany, Ok
Posts: 382
|
Re: Model A motor froze-up
Is the motor still in the car? Starter still installed. A wedged starter drive can make a motor seem froze. If it is really froze up as Donino said soak with good penatrting oil. Half automatic transmission fluid and acetone makes a good penatrting oil. Time and patience.
|
08-17-2013, 09:52 PM | #4 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Thank you for your quick reply. I'll give it a try. Hope I can find the "Kroil."
|
08-17-2013, 10:09 PM | #5 |
Senior Member
Join Date: May 2010
Location: Stayton, Oregon
Posts: 3,806
|
Re: Model A motor froze-up
How did it freeze up? While running, been sitting for 10 years, or ????? It would depend on how it happened as to how to unfreeze.
__________________
Fred Kroon 1929 Std Coupe 1929 Huckster |
08-17-2013, 10:35 PM | #6 |
Senior Member
Join Date: May 2010
Location: Tucson, Arizona
Posts: 374
|
Re: Model A motor froze-up
Sponsored Links (Register now to hide all advertisements)
|
08-17-2013, 10:45 PM | #7 |
Senior Member
Join Date: May 2010
Posts: 4,179
|
Re: Model A motor froze-up
Fifty-five years ago, had one engine sitting outside for 10 years that locked up.
1. Took it inside, removed head, removed oil pan, & removed crankshaft; "then" found (3) pistons could move & (1) could not. 2. Only concentrated on soaking & moving this (1) non-moving piston. 3. Back then, soaked with Liquid-Wrench for about a week & lightly tapped top of piston with a pine 2x4 every day after soaking for (2) days. 4. It finally broke loose, so I kept the same rings, same pistons, then honed cylinders slightly & re-assembled -- great engine. |
08-17-2013, 11:19 PM | #8 | |
Senior Member
Join Date: May 2010
Location: Camarillo, CA and Pine Grove, CA
Posts: 2,843
|
Re: Model A motor froze-up
Quote:
Here is where you get it. http://kanolabs.com/
__________________
1921 Runabout 1930 Tudor Early 1930 AA Speed costs money. How fast do you want to go? |
|
08-17-2013, 11:32 PM | #9 |
Senior Member
|
Re: Model A motor froze-up
WAIT WAIT WAIT
Before you follow the great advise given here, like Fred asked how did it freeze up? Sitting many years long? Drove it and it stopped while driving? Worked fine the would not restart after stopping? Each of these have a different starting point.
__________________
What's right about America is that although we have a mess of problems, we have great capacity - intellect and resources - to do some thing about them. - Henry Ford II |
08-18-2013, 01:35 PM | #10 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Thank you for responding. The motor and starter are still in this 1929 Ford pickup. All the parts are there. It has stood stationary for several years (indoors).
|
08-18-2013, 01:47 PM | #11 |
Senior Member
Join Date: Jul 2010
Location: Cow Hampshire
Posts: 4,188
|
Re: Model A motor froze-up
I would remove the starter and try to pull it over by hand with a crank first. (that eliminates the jammed bendix possibility right away.)
THEN maybe go into lubricant/solvent mode for a while doing all the suggestions each time trying the hand crank to move it. THEN maybe the dowel in the spark plug hole (careful - go easy - you don't want to punch a hole in the top of the piston.) Maybe alternate with compressed air on a cylinder which seems not leaky and the valves are closed (one of these is sure to be so.) THEN maybe take a step back, get yer tools out and start by taking the head off. Rinse and repeat with the 2x4 like the dowel trick, but the larger impact area will allow you greater impact/force. THEN MAYBE go forward with a more complete disassembly in place to determine the place where it is binding. You may find one piston hung up if you have/had a coolant leak unknown in the past. About then I would pull the engine and tear it down formally after proper introductions. No more Mr/Ms nice person. Joe K
__________________
Shudda kept the horse. |
08-18-2013, 03:22 PM | #12 |
Senior Member
Join Date: Apr 2011
Location: New Zealand
Posts: 444
|
Re: Model A motor froze-up
Back in the early sixties I bought a '29 Phaeton with a siezed motor and the head off. We Towed to the top of a steep hill and coasted down the hill with a friend lying on the front mudguard.
When I dropped the clutch it started turning over and the friend squirted oil down the bores, We got many good miles out of the engine before it needed a rebuild. I wouldn't recommend that procedure today! Keith |
08-18-2013, 08:46 PM | #13 |
Senior Member
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
|
Re: Model A motor froze-up
A 4 wheel moving cart works well.
I would remove the 4 spark plugs and squirt some diesel and ATF, or Kroil, or any good penetrating oil, let it set for a day or two, then put the car in high gear and try rocking it back and forth. If that doesn't work the I made a tools from a bad starter end plate and pinion that works pretty well to unstick motors. |
08-18-2013, 09:20 PM | #14 |
Senior Member
Join Date: May 2010
Location: Stayton, Oregon
Posts: 3,806
|
Re: Model A motor froze-up
When I had my huckster engine rebuilt, after having it in our barn for many years, the rebuilder had to break the pistons to get them out. It had the head off and mice had a great time living in it. So it may be hard to tell what you need to do. Maybe just start with some of the suggestions above and see what happens.
__________________
Fred Kroon 1929 Std Coupe 1929 Huckster |
08-18-2013, 10:10 PM | #15 |
Senior Member
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
|
Re: Model A motor froze-up
Here's the tool I made to help with stuck motors. With a good soak and this tool, hopefully it would come free. But as mentioned earlier, soak the cylinders first then try rocking the car back and forth in high gear. Rock it a couple times a day and it might come loose.
http://www.fordbarn.com/forum/showth...l+stuck+motors |
08-18-2013, 11:04 PM | #16 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
I'm overwhelmed with all these helpful responses. I'm glad to have so many choices, if one doesn't work, the next one will. I'll be looking for product and experimenting. Hopefully, I won't have to tear the head off. Betsy worked fine when I parked it some 30 years ago, so I'm supposing the inactivity made it lock-up. I am concerned about rust even though it shows oil on the dip stick. I can't move the crank shaft using the crank. But, I don't want to apply too much pressure afraid I'd hurt something inside. I will try the soaking, rocking in third gear. Not sure of the product availability in our small town. I'll keep you all posted.
|
08-18-2013, 11:19 PM | #17 |
Senior Member
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
|
Re: Model A motor froze-up
Where are you located?
|
08-19-2013, 10:10 AM | #18 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
North Dakota
|
08-19-2013, 10:25 AM | #19 |
BANNED
Join Date: May 2010
Location: Walla Walla, Washington USA
Posts: 6,066
|
Re: Model A motor froze-up
I understand that "Kroil" is 1/2 acetone and 1/2 ATF (Automatic Transmission Fluid)...Is that correct?
Pluck |
08-19-2013, 10:26 AM | #20 |
BANNED
Join Date: May 2010
Location: Walla Walla, Washington USA
Posts: 6,066
|
Re: Model A motor froze-up
|
08-19-2013, 11:10 AM | #21 |
Senior Member
Join Date: May 2010
Location: Fairfax, VA
Posts: 3,398
|
Re: Model A motor froze-up
Karl used to post on this site and had a great story about starting a stuck engine. he made a spark plug into a grease fitting and pumped the cylinder on the down stroke with grease. He kept pumping until the jug popped loose. He then fired up the engine is his garage! He said everything was covered with burnt grease!
|
08-19-2013, 03:36 PM | #22 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
I found Kroil locally. I'll give it a try today.
Aww, patience, someone said. I'll let it soak a day or two before rocking it. |
Sponsored Links (Register now to hide all advertisements) |
|
08-19-2013, 07:56 PM | #23 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Ha! The guy at the NAPA store fibbed. He didn't have the Kroil. I did manage to get the MMO Marvel Miracle Oil from him though. I took the spark plugs out, poured about a cup of MMO into each spark plug hole, put Betsy into high gear, and then my husband and I rocked the pick up back and forth. Heard sloshing somewhere. Not sure if it was in the motor or if it was old gas. Will try the crank in a few days and perhaps more rocking. I'm thinking about emptying the radiator, putting clean water through for a flush. Will want to put water back in, but need a coolant. What should I mix with the water? Antifreeze or alcohol? I sound like a kindergarten kid, but I have to start at the beginning. Thanks for your help.
|
08-19-2013, 07:58 PM | #24 |
Senior Member
Join Date: Jun 2010
Location: Eastern, CT
Posts: 527
|
Re: Model A motor froze-up
I wouldn't worry about the radiator yet. Concentrate on getting the engine turning over with some compression and then go from there. Just my $0.02.
Red |
08-19-2013, 08:17 PM | #25 | |
Senior Member
Join Date: May 2010
Location: Bucks Co, Pa
Posts: 3,740
|
Re: Model A motor froze-up
Wow! I think half a cup would have been plenty! It's OK though, Just try to catch it when it runs out of the spark plug holes. If there water/Antifreeze in the engine thats good, No leaks! Let's concentrate on the engine first. Cooling system can come later. While you're soaking the engine, better drain all the old gas and flush the tank. There may be rust particles. Pour a little fresh gas directly through the tank. Maybe half a gallon or so to flush all the crud out. Reassemble the system and take the fuel line off and make sure it's clear. before you put the gas line on the carburetor, put a little gas in the tank and open the valve and see if it runs through. Keep rocking it in 3rd gear all the while.
Terry Quote:
|
|
08-19-2013, 09:02 PM | #26 | |
Senior Member
Join Date: Aug 2011
Location: Eagle Bend, MN
Posts: 2,028
|
Re: Model A motor froze-up
Sponsored Links (Register now to hide all advertisements)
Quote:
|
|
08-19-2013, 10:30 PM | #27 | |
Senior Member
Join Date: Jun 2010
Location: Huntsville, AL
Posts: 538
|
Re: Model A motor froze-up
Quote:
Before: Soaking: |
|
08-20-2013, 02:36 AM | #28 |
Senior Member
Join Date: Nov 2011
Location: Sonoma, CA.
Posts: 1,504
|
Re: Model A motor froze-up
Pull off the valve cover and make sure the valves are opening and closing useing a screw driver or something like it to check them. For some reason Model A's stick valves
when they sit. They can lock up a motor just like the pistons can. Just make sure they are free before you try to unstick the rest of the motor. I have seen a couple of blocks where they tried to tow the car to unstick the motor and broke the lifter bosses right out of the motor. So after the valves are unstuck check the lifters also. And the ATF and Acentone thing really works, better than anything I've ever used. Happy unsticking........... Dodge |
08-20-2013, 08:06 AM | #29 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Thank you, Dodge, for this helpful suggestion. I'll give this one a try for sure.
|
08-20-2013, 08:07 AM | #30 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
This one gives me hope.
|
08-20-2013, 06:05 PM | #31 |
Senior Member
Join Date: May 2010
Location: Richland Mi.
Posts: 1,172
|
Re: Model A motor froze-up
It wasn't mentioned but I hope that you didn't put the spark plugs back in.
|
08-23-2013, 03:47 PM | #32 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Ross/Kzoo, Oops! Yes, I did.
Need to leave them removed? With my lack of knowledge I need all information I can get to not back-step. |
08-23-2013, 04:10 PM | #33 | |
Senior Member
Join Date: Jun 2010
Location: Huntsville, AL
Posts: 538
|
Re: Model A motor froze-up
Quote:
Just be sure and take them back out before you try and rotate the engine. You can't compress a liquid and if you try, bad things will happen. |
|
08-23-2013, 05:36 PM | #34 |
Senior Member
Join Date: Jun 2012
Location: Sheffield Lake, Ohio
Posts: 137
|
Re: Model A motor froze-up
Once while watching Chasing Classic Cars, Roger the old mechanic let it slip that MMO was their "secret juice" they put in the cylinders to loosen engines that have been sitting for a long time. Seems to work for them.
|
08-23-2013, 05:41 PM | #35 |
Senior Member
Join Date: May 2010
Location: Richland Mi.
Posts: 1,172
|
Re: Model A motor froze-up
Yes, leave them out until you get that motor spinning freely.
|
08-23-2013, 06:54 PM | #36 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
I'm thinking I may have to go this route. The pouring Marvel's Miracle Oil and rocking isn't enough.
|
08-23-2013, 06:56 PM | #37 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
I'm going to keep trying the MMO. But am also thinking of removing the head to take a look inside.
|
08-23-2013, 06:57 PM | #38 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Okay, Ross/Kzoo.
I put more MMO in. Will let it set 24 hours, and try again. I bought a gallon. Have poured in 2 qts. |
08-23-2013, 07:03 PM | #39 |
Senior Member
Join Date: May 2010
Location: Richland Mi.
Posts: 1,172
|
Re: Model A motor froze-up
If you check the archive you'll see that many Barners will walk by their projects every couple of days and squirt some MMO or other products for weeks before trying to get it turning. Be patient but most of all try to get in touch with a Model A person or old time mechanic to help you with this. You seem to be in a remote area there. My niece lives in Dickinson and BIL and SIL in Baker Mt. so I get by there every so often.
Did you drain the crankcase? If so what did the fluids look like? |
08-23-2013, 07:26 PM | #40 |
Senior Member
Join Date: May 2010
Location: Southern California
Posts: 7,052
|
Re: Model A motor froze-up
Remember too much force and you will be adding bent rods, a bent crank etc to your list of problems.
Charlie Stephens |
08-23-2013, 08:50 PM | #41 |
Senior Member
Join Date: May 2010
Location: Bucks Co, Pa
Posts: 3,740
|
Re: Model A motor froze-up
Be patient and keep trying and one day, BING!!! it will let go for you. I wouldn't take the head off just yet. The engine will still be stuck and you will have to put the head back on, A complicated process for a non mechanic. Just keep rocking it, it will break free!
Terry |
08-23-2013, 10:27 PM | #42 |
Junior Member
Join Date: Jun 2010
Posts: 25
|
Re: Model A motor froze-up
Coca Cola Classic in the cylinders. My buddy busted a few flatheads with it loose. And I got a A motor spinning last week after using it. I didn't buy it but I tried it and it worked.
|
Sponsored Links (Register now to hide all advertisements) |
|
08-23-2013, 11:42 PM | #43 |
Senior Member
Join Date: Dec 2010
Location: FRESNO, CA
Posts: 12,560
|
Re: Model A motor froze-up
I previously suggested to fill the crankcase & cylinders to OVERFLOWING with diesel & let it SOAK for weeks! NO ONE replied, either YEY or NAY! So, I deleted it! At least this way has a chance for the diesel to soak into ALL the internals Bill W.
__________________
"THE ASSISTANT GURU OF STUFF" |
08-24-2013, 06:18 AM | #44 |
Senior Member
Join Date: May 2010
Location: NC
Posts: 2,975
|
Re: Model A motor froze-up
|
08-24-2013, 07:39 AM | #45 |
Senior Member
Join Date: Sep 2011
Location: Meridian, ID
Posts: 568
|
Re: Model A motor froze-up
Sounds like you are on the right track. Persistence and patience will pay off. We would love to see pictures of your Model A! I lived in Grand Forks, ND for seven years while attending UND and flight instructing and did a lot of cross country flights out near Devils Lake and your neck of the woods. I know of a couple other Model A'ers on the fordbarn from Nodak that might be able to give you a hand also. Good luck!
__________________
Aaron in Tacoma (although still a Montana hillbilly at heart ) |
08-24-2013, 08:35 AM | #46 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Sponsored Links (Register now to hide all advertisements)
|
08-24-2013, 08:38 AM | #47 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Thank you, fordman. My aim is to see Betsy up and running one day. She's been idle a long time. I've neglected my prized old friend for too long. Now's her time. With all the suggestions I've been receiving even these dish-pan hands will see her going again. Thanks to all the interest and expert advice, we'll get her going.
|
08-24-2013, 08:41 AM | #48 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Ha! George Miller.
It is in the 90s here in ND. I'd hate to see it get much warmer~with a smile. |
08-24-2013, 08:46 AM | #49 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Sorry Bill Williamson,
I must have missed your suggestion to "fill up to overflowing." Last fall I did put about a pint of diesel fuel into the 4 spark plug holes. I left it over the winter expecting results this spring. No such luck. Since then, in my discouragement, I've left Betsy until now. I'm back with determination to get that motor loosed. My present task has me using Marvel's Miracle Oil. I have poured 2 quarts of it into the 4 spark plug holes, set the gear to high, rock Betsy back and forth with gusto. The crank handle moves slightly, but no "break-through" yet. I'll keep trying. |
08-24-2013, 02:08 PM | #50 | |
Senior Member
Join Date: Dec 2010
Location: FRESNO, CA
Posts: 12,560
|
Re: Model A motor froze-up
Quote:
It turned out to be a really good engine and in it's lifetime, I used it in 3 different Model A's. (OH! Chief was my Dad & Model A mentor & I quote him often. He "built" dependable "A" Models in his spare time & sold them, so we could EAT!!) Bill W.
__________________
"THE ASSISTANT GURU OF STUFF" |
|
08-24-2013, 02:09 PM | #51 | |
Senior Member
Join Date: May 2010
Location: Bucks Co, Pa
Posts: 3,740
|
Re: Model A motor froze-up
A couple of important questions! Does the crank handle move? How about the fan? (Someone watches while the other rocks) It sounds like you're well on the way. Did you check the oil level in the crankcase? Has any of the Marvel's Mystery Oil leaked down through the rings and into a crankcase? You should have six to seven quarts in the CC now. That's good too!
Terry (Just keep rockin") Quote:
|
|
08-24-2013, 02:18 PM | #52 | |
Senior Member
Join Date: May 2010
Location: Richland Mi.
Posts: 1,172
|
Re: Model A motor froze-up
Quote:
I don't see why you should get preferential treatment! LOL |
|
08-24-2013, 05:39 PM | #53 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Wished I'd had a "Chief" to give me pointers today. When my Dad worked on Betsy, I paid no attention. My loss. I wasn't interested then.
I added more Marvel's Miracle Oil today, rocked some more, will try again. The crank moves only a little. The fan moves slightly with it. Will keep rockin. My husband likes to tinker too, but he's guessing right along with me. |
08-24-2013, 05:54 PM | #54 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Thanks, Charlie. I'm taking it slow and easy. The crank is quite solid, won't force anything.
|
08-24-2013, 05:59 PM | #55 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
How do I "drain the crankcase?"
|
08-24-2013, 06:02 PM | #56 | |
Senior Member
Join Date: Dec 2010
Location: FRESNO, CA
Posts: 12,560
|
Re: Model A motor froze-up
Quote:
Chief used to say, "We're ALL insecure & need attention & sympathy, it's just that some won't admit it"!! Bill W.
__________________
"THE ASSISTANT GURU OF STUFF" |
|
08-24-2013, 06:17 PM | #57 |
Senior Member
Join Date: May 2010
Location: Richland Mi.
Posts: 1,172
|
Re: Model A motor froze-up
Keep her rocking. Soon you will see movement growing exponentially. First 1/100th of a revolution then 1/75th then 1/25th and on and on. Sounds like it will free up!
Again, leave the plugs out of it until it spins freely with the starter. |
08-24-2013, 06:18 PM | #58 |
Senior Member
Join Date: May 2010
Location: Homestead, Fl
Posts: 351
|
Re: Model A motor froze-up
Personally I'd forgo the MMO for now and use 50/50 ...ATF/acetone. It's a thinner solution that I think penetrates quicker and a proven "unsticker". I have a formally "stuck" A engine that I unstuck. I put a 3/4 inch drive, 1 7/16 socket on the crank pully (engine was on the ground) with a breaker bar and nudged it every day til it moved. 1/8 inch, 1/4 inch 1/2 inch ect. doesn't take long once you get a little movement going. It worked for me. Good luck!
|
08-24-2013, 06:51 PM | #59 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Thanks, Rusty.
Wished I'd gone the 50/50 before I did the MMO. Now, if I can figure out how to drain out all that MMO . . . I'm going to keep trying any "unsticker" that will possibly work. |
08-24-2013, 06:51 PM | #60 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Ok, Ross.
|
08-24-2013, 07:02 PM | #61 |
Senior Member
Join Date: May 2010
Location: Richland Mi.
Posts: 1,172
|
Re: Model A motor froze-up
Betsy, I don't think that you are to that point yet. After you get that motor spinning most the MMO will come out of the spark plug holes and past the valves to the crankcase. That is good thing to have the MMO around the valves and valve stems. At that point you may want to remove the drain plug and see what comes out besides oil.
Last edited by Ross/Kzoo; 08-24-2013 at 07:14 PM. |
08-24-2013, 07:03 PM | #62 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
montanafordman,
I posted a picture of Betsy on my profile page. Haven't figured out how to get it out of there. |
Sponsored Links (Register now to hide all advertisements) |
|
08-24-2013, 07:04 PM | #63 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Aha! The more I hear the more things make sense. Thanks.
|
08-24-2013, 07:13 PM | #64 |
Senior Member
Join Date: Apr 2011
Posts: 319
|
Re: Model A motor froze-up
First try removing the starter. i've found many with the starter drive hung up and not just Model A's. Acetone and Atf works if it is actually stuck. Then load it on a trailer,chain it loosely and put it in high gear. drag aroung with you and watch the fan blade as the car tries to roll. i've had tractors free in a trip to lonch. Worst one took two days of following me. Good luck!!!!!!!!!!!
|
08-24-2013, 07:56 PM | #65 |
Senior Member
Join Date: Jul 2013
Location: San Antonio, Texas
Posts: 687
|
Re: Model A motor froze-up
My engine was stuck about 3 weeks ago also. What I did to settle my curiosity was remove the oil pan and dry every piston and rod really good. So when I poured the mixture in each cylinder I could clearly see from the bottom of the engine which cylinder was allowing the fluid to leak past the rings. The dry piston and rod is the culprit. The one stuck. Eventually I still pulled the head off to which I was glad I did due to the number 1 cylinder being severely gouged from a broken locking pin and moving piston pin.
|
08-24-2013, 08:26 PM | #66 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Sponsored Links (Register now to hide all advertisements)
|
08-24-2013, 08:28 PM | #67 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Anteek, thanks. Will keep posting progress - when I get some.
|
08-24-2013, 08:41 PM | #68 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Happy for your success. Mine is yet to come.
|
08-24-2013, 08:55 PM | #69 | |
Senior Member
Join Date: May 2010
Location: Bucks Co, Pa
Posts: 3,740
|
Re: Model A motor froze-up
I know this was well intentioned, But.... You're asking a woman who has very limited mechanical experience to crawl underneath a truck that's been sitting in place for over 50 years. Then know how to take a oil pan down. At some point she's going to have to put it back, new gaskets and all. A Formidable task to be sure. In fact, I regards taking an oil pan down as a really rotten job and I know what's involved. Think of what could go wrong for a person who has never done it before. I believe this engine can be freed without taking it apart. In fact I think that she's almost there with the crank starting to move.
Terry Quote:
|
|
08-24-2013, 08:59 PM | #70 |
BANNED
Join Date: May 2010
Location: Bucks County, PA
Posts: 11,454
|
Re: Model A motor froze-up
wouldnt it be something if it turned out to be a frozen brake drum and stuck clutch disc.
Last edited by Mitch//pa; 08-24-2013 at 09:05 PM. |
08-24-2013, 09:17 PM | #71 |
Senior Member
Join Date: May 2010
Location: Bucks Co, Pa
Posts: 3,740
|
Re: Model A motor froze-up
What comes Next! Betsey, when you do get it to turn over, remember, there is rust on the cylinder walls and the camshaft and other parts as well. This rust rubs off and gets into the oil as an abrasive particle, much like sand. And much like sand, they can destroy the engine. It is a balancing act to know how long you should take to get this contaminated oil out of the system. Too long and you risk damage, too soon and you don't get enough of the particles. The old story I heard was about ten minutes at idle speed. Then it has to be changed. When it's changed, pour a qt. of diesel/fuel oil through the engine to flush what ever particles are left behind. This will begin the desludgeing process. Put the cheapest DETERGENT oil you can find. After about five hours (of running) or so, Drain this oil out and replace with a somewhat better quality oil. Terry
|
08-24-2013, 09:34 PM | #72 |
Senior Member
Join Date: May 2010
Location: Bucks Co, Pa
Posts: 3,740
|
Re: Model A motor froze-up
YES!!! I know why a Dr won't diagnose over the phone! You try to think of everything! Without seeing it, it's all a guessing game, but with probabilities.
Mod A engines are prone to seizing up after long periods of inactivity. Same with my Allis Chalmers. I had to free the engine up[, The previous owner hadn't started it in about three years. MMO did the trick for me. That is the the 1938 A.C. mod B in my profile. Terry |
08-25-2013, 02:50 AM | #73 | |
Senior Member
Join Date: Dec 2010
Location: FRESNO, CA
Posts: 12,560
|
Re: Model A motor froze-up
Quote:
Think about it Sonny Boy, Iffin' the disc wuz stuk, wouldn't matter none, iffin' the transfuselator wuz in NEUTRAL! (Thet's where the stick will WOBBLE side to side, like in the middle uf the "H" pattern! (BUT, I cain't shift it fer you, NO THUMBS) Buster T.
__________________
"THE ASSISTANT GURU OF STUFF" |
|
08-25-2013, 06:00 AM | #74 | |
BANNED
Join Date: May 2010
Location: Bucks County, PA
Posts: 11,454
|
Re: Model A motor froze-up
Quote:
Ill send you a bone |
|
08-25-2013, 07:50 AM | #75 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Terry, NJ
You got me pegged. All suggestions given have given me both a heavy-heart of defeat before I get going, and yet, a desire to keep going. I'm going to keep trying. I'll report if I get ANY success. If not, I'll try another suggestion. I do have "cheap" oil on hand for a flush. I also have ATF and acetone on hand for another option. I've been trying to get the plug out of the oil pan, but it, too, is stuck. I sprayed it with liquid wrench, leaving it to penetrate. Will give it another try today. Yes, I'm a 72-year-old woman, with a new mechanical passion. Thanks, Fellows. Last edited by BetsyModelA; 08-27-2013 at 08:21 AM. |
08-25-2013, 07:59 AM | #76 |
Senior Member
Join Date: May 2010
Location: Richland Mi.
Posts: 1,172
|
Re: Model A motor froze-up
It didn't get stuck overnight and it won't get unstuck overnight. Just keep "plugging" away. Sorry I couldn't resist that one. When loosening stuck bolts/plugs sometimes a little force in the opposite direction will help loosening.
|
08-25-2013, 08:21 AM | #77 |
Senior Member
Join Date: May 2010
Location: Homestead, Fl
Posts: 351
|
Re: Model A motor froze-up
"All suggestions given have given me both a heavy-heart of defeat before I get going, and yet, a desire to keep going"
DON'T YOU DARE LET IT BEAT YOU!!!. If there's one thing us old farts have learned over the years is patience. If it doesn't break loose today, it's just not ready yet. So you wait for the next day, or the next one. It'll come. Just keep bumpin' it. |
08-25-2013, 10:10 AM | #78 |
Senior Member
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
|
Re: Model A motor froze-up
I wouldn't worry about draining the pan yet, but it would be nice to loosen the plug to see if antifreeze comes out first. It it does, then it might be time to take the engine apart. I had to do a GM inline 6 that was stored for 5 or 6 years with antifreeze that leaked into the cylinders. It was stuck very tight and I had to pull the head, pan and pistons out to get it unstuck and give it an overhaul. If antifreeze doesn't come out the drain plug that's a very good sign and I'd keep rocking the car back and forth in high gear.
I do like the idea of chained loose on a trailer, then towing it around as a way to loosen a stuck engine. |
08-25-2013, 10:12 AM | #79 |
Senior Member
Join Date: May 2010
Location: NC
Posts: 2,975
|
Re: Model A motor froze-up
Like Tom I have a old starter with a nut welded on the end of of the armature shaft. Not as nice as Tom's but does the job. At this point it would break it loose, always works. If you have a old starter try it. Tom gave you some good advice.
|
08-25-2013, 11:42 AM | #80 |
Senior Member
Join Date: May 2010
Location: So Cal
Posts: 8,794
|
Re: Model A motor froze-up
I know there are no MAFCA or MARC clubs in North Dakota but maybe someone with
a roster can see if there are any members in ND that could help. |
08-25-2013, 02:28 PM | #81 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Thanks Rusty. I'm not giving up yet.
|
08-25-2013, 02:29 PM | #82 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Thanks, Bob, I'll check the MARC online.
|
Sponsored Links (Register now to hide all advertisements) |
|
08-25-2013, 02:33 PM | #83 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Okay, I'll keep twisting, turning, rocking, squirting and pouring. Instead of shopping for a new purse, I'm going shopping for a good set of wrenches.
|
08-25-2013, 07:14 PM | #84 |
Senior Member
Join Date: May 2010
Location: Bucks Co, Pa
Posts: 3,740
|
Re: Model A motor froze-up
Betsey, I've been thinking about your car and I'd like to know if it will roll without the engine. Can you hook it up behind something and pull it? At least out of the shed/barn in neutral? Will it roll? I think I want to confirm that something else isn't stuck. Was the Emergency brake on for all that time? I think I would hitch it to a big lawn tractor or a truck and yank it out of there just to make sure the brakes aren't seized or something else. Terry
PS don't pour any more MMO into the engine, it's got enough! |
08-26-2013, 11:10 AM | #85 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Thank you, Terry.
It does roll in neutral. The motor is full of MMO. The emergency brake is not on. The brakes are fine. I'm still rocking it. |
08-27-2013, 07:06 PM | #86 |
Senior Member
Join Date: Feb 2011
Location: NNNNNNNNJJJJJJJJJJ
Posts: 6,823
|
Re: Model A motor froze-up
Sponsored Links (Register now to hide all advertisements)
I am going through the same thing currently. I have freed several engines in the past and it was a piece of cake. The model A engine I am now trying to unfreeze is in the same predicament as yours. Have always had great success with ATF-not this time. Mixed it down with gas to thin it and nodda. Today I tried the boiling coke trick and nodda. Even pulled it slowly around the yard with my pu-nodda. My next move is to empty the pan, and overfill with diesel as Bill suggests. Then I think I will take a nap for about a month and give it a go again. Never had one this stubborn, but going to beat it. So don't give up and give it plenty of time.... |
08-28-2013, 07:18 AM | #87 |
Senior Member
Join Date: May 2010
Location: Bucks Co, Pa
Posts: 3,740
|
Re: Model A motor froze-up
Betsey, I assume you've been rocking back, in third gear? Try putting it in reverse. The idea being to turn the engine in the opposite direction. See if you can get a little motion out of the fan turning it backwards.
Terry |
08-28-2013, 08:28 AM | #88 |
Senior Member
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
|
Re: Model A motor froze-up
By rocking the car in high gear you get the most leverage, and by rocking back and forth the crank is forced to move both directions. Low or reverse will give the crankshaft very little force.
|
08-28-2013, 09:29 AM | #89 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Thank you, Ronn, for your encouragement. Sorry to hear you, too, are having a stubborn motor to "unfreeze." I'll keep trying. Patience and persistence. Please report when yours comes free.
Last edited by BetsyModelA; 08-28-2013 at 09:35 AM. |
08-28-2013, 09:35 AM | #90 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Yes, Terry, I have been rocking it in third gear. So far, all that's happening is I get a lot of slosh coming from the gas tank. I'm wondering what's happening in there. I'm supposing I should remove that gas, perhaps even the gas tank to clean it out.
Okay, I'm getting away from where I need to be - the motor unlock. I think, for a change, I will put it in reverse. I'm trying everything suggested - short of sending it over a steep hill with a push. (That was meant to be a joke, only.) I'm afraid to pull it in gear. I don't want to hurt something else that might be stuck as well. So, I'm rockin and a rollin. Sounds like something from the 50s. |
08-28-2013, 09:47 AM | #91 |
Senior Member
Join Date: May 2010
Location: Richland Mi.
Posts: 1,172
|
Re: Model A motor froze-up
Is the fan belt tight and when rocking it in 3rd gear is there any movement of the fan blade?
PS Also when moving my car it's easier to grab a tire at the 10 O'clock and 2 O'clock position and use that position for the rocking grip. |
08-28-2013, 02:34 PM | #92 |
Senior Member
Join Date: Feb 2011
Location: NNNNNNNNJJJJJJJJJJ
Posts: 6,823
|
Re: Model A motor froze-up
Tom is correct, reverse is too low a gear-keep it in 3rd.
|
08-28-2013, 04:02 PM | #93 |
Senior Member
Join Date: Dec 2010
Location: FRESNO, CA
Posts: 12,560
|
Re: Model A motor froze-up
Betsy,
I REPEAT, keep the cylinders & crankcase filled to OVERFLOWING with diesel & let'er soak for weeks! Bill W.
__________________
"THE ASSISTANT GURU OF STUFF" |
08-28-2013, 04:07 PM | #94 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Yes, Ross, the fan belt is tight as well. It does, however give a slight back and forth motion along with the crank when I rock Betsy back and forth. Also, for the rocking motion, I am able to grasp the spare tire holder by the left door with my right hand and grasp the headlight/horn post with my left hand and rock quite briskly. The crank gives a clunk-clunk sound as it jerks with the movement. One positive note: I'm developming a good grip in my hands with this constant activity.
|
08-28-2013, 04:09 PM | #95 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Bill, there seems to be an overflow with only one of the spark plug holes. Should I put in more? If I thought it would help, I'd drain the MMO, put in the ATF/acetone solution, and give that mixture a try. What say you?
|
08-28-2013, 04:24 PM | #96 |
Senior Member
Join Date: May 2010
Location: Richland Mi.
Posts: 1,172
|
Re: Model A motor froze-up
If you are getting some movement then that's encouraging. It should continue to get increased movement as rocking progresses.
|
08-28-2013, 04:27 PM | #97 |
Senior Member
Join Date: Dec 2010
Location: FRESNO, CA
Posts: 12,560
|
Re: Model A motor froze-up
Yep, some cylinders will drain down because of some open valves. It's apparent that the pistons are stuck, so concentrate on keeping pouring stuff in the spark plug holes. Bill W.
__________________
"THE ASSISTANT GURU OF STUFF" |
08-28-2013, 04:32 PM | #98 |
Senior Member
Join Date: May 2010
Location: Richland Mi.
Posts: 1,172
|
Re: Model A motor froze-up
Bill, sounds like you need to make a "house call". LOL
|
08-28-2013, 05:16 PM | #99 |
Senior Member
Join Date: May 2010
Location: Bismarck ND
Posts: 1,189
|
Re: Model A motor froze-up
I am in Bismarck, and have 6 Model As. I also have built one of the tools that Tom describes. I may be able to come to Harvey sometime soon if you wish.
|
08-28-2013, 05:59 PM | #100 |
BANNED
Join Date: May 2010
Location: Bucks County, PA
Posts: 11,454
|
Re: Model A motor froze-up
midget thanks for offering to come to the rescue and help these people out. thats what makes this forum so good is members like you. i sure hope they take you up on your offer
|
08-28-2013, 06:04 PM | #101 |
Senior Member
Join Date: May 2010
Location: Bucks Co, Pa
Posts: 3,740
|
Re: Model A motor froze-up
Tom, of course is correct! You get the greatest gear advantage in third gear and your least in reverse, but what I wondered was could the engine be turned in the opposite direction. Was something up against something that was stuck and stopping. Would it turn in the opposite direction?
Terry |
08-28-2013, 06:06 PM | #102 |
BANNED
Join Date: May 2010
Location: Bucks County, PA
Posts: 11,454
|
Re: Model A motor froze-up
zz read post #99
Last edited by Mitch//pa; 08-28-2013 at 06:13 PM. |
Sponsored Links (Register now to hide all advertisements) |
|
08-28-2013, 06:46 PM | #103 |
Senior Member
Join Date: May 2010
Location: Bucks Co, Pa
Posts: 3,740
|
Re: Model A motor froze-up
Yeah Bill, That thing is gonna smoke like hell when it finally starts. At least a quart of MMO in the manifolds and tailpipe. Mosquito killer! Let's get it cranking over first. Betsey says there's been a very little movement in the fan which kinda says maybe the pistons aren't stuck. I'm grabbing at straws, but I'm wondering if maybe it's a couple of lifters are really locked up. Or maybe the cam itself is locked (center bearing, iron on iron). The fiber cam gear would flex a little, but the cam wouldn't turn.
Terry |
08-28-2013, 06:47 PM | #104 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Got good news! I'm excited! Not big news, but nevertheless good news!
The fan moved. I can now turn it full circle - both ways. I'm hoping that's a start. Thanks for the idea "for someone to come and help me out." I located a relative who is interested in traveling to our home to "look at" Betsy. I'm hoping he brings his wrench set. I'll keep everyone posted. In the meantime, I'm still rockin and rollin - with a little more vigor. |
08-28-2013, 07:12 PM | #105 |
Senior Member
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
|
Re: Model A motor froze-up
That's great news. I knew as long as you got the fan to move any at all, it wouldn't be long until the engine goes all the way around. Hopefully you don't also have4 a bunch of stuck valves. If you do then a bent screwdriver through the spark plug holes might get them pushed back down.
I just got a Honda 2 cylinder water cooled lawn mower engine to move freely by using MMO in the cylinders. |
08-28-2013, 07:14 PM | #106 |
Senior Member
Join Date: May 2010
Location: Homestead, Fl
Posts: 351
|
Re: Model A motor froze-up
Sponsored Links (Register now to hide all advertisements)
|
08-28-2013, 07:20 PM | #107 |
Senior Member
Join Date: May 2010
Location: Richland Mi.
Posts: 1,172
|
Re: Model A motor froze-up
Oh Happy Day!
|
08-28-2013, 08:13 PM | #108 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Thanks, All, for your advice and enthusiasum.
I'm expecting to get more action - soon. I'll let you know when the crank makes a move. Hopefully, soon. |
08-28-2013, 08:19 PM | #109 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
midgetracer, you're welcome at our home anytime. I'd love to show you Betsy.
|
08-28-2013, 08:38 PM | #110 |
Senior Member
Join Date: May 2010
Location: So Cal
Posts: 8,794
|
Re: Model A motor froze-up
Ok I'm confused, you said the fan turns in post 104 and then in post 108
"I'll let you know when the crank makes a move" Bob |
08-28-2013, 09:37 PM | #111 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Okay, Bob C, Perhaps you can tell me what is happening.
The crank does not turn, or move, only slightly when I rock Betsy. The fan blades now turn when I move them with my hands. I guess I didn't make that clear with my recent post. You see, the fan blades were stuck solid before today. Now they turn with my manual force. I didn't mean to mislead anyone into thinking that the motor was moving, only the fan. Even that to me was a break-through as a beginning toward success. |
08-28-2013, 11:34 PM | #112 |
Senior Member
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
|
Re: Model A motor froze-up
As long as the crankshaft moves a little back and forth, then continued rocking should get it to slowly rotate more. That's good that you got the fan free because a stuck water pump can greatly hold back an engine if the belt is tight.
|
08-29-2013, 12:22 AM | #113 |
Senior Member
Join Date: Dec 2010
Location: FRESNO, CA
Posts: 12,560
|
Re: Model A motor froze-up
Dog here,
Iffin' the starter's off, get a pry bar onto the flywheel TEETH, a LOT of pressure can be applied thet a way! Buster T.
__________________
"THE ASSISTANT GURU OF STUFF" |
08-29-2013, 01:16 AM | #114 |
Senior Member
Join Date: May 2010
Location: Portland, Oregon
Posts: 5,920
|
Re: Model A motor froze-up
Bill, that seems like it could crack the flywheel housing. I'd be cautious about that.
__________________
Ray Horton, Portland, OR As you go through life, keep your eye on the donut, not the hole. |
08-29-2013, 04:44 AM | #115 | |
Senior Member
Join Date: Dec 2010
Location: FRESNO, CA
Posts: 12,560
|
Re: Model A motor froze-up
Quote:
Chief always drilled a 5/8" hole in the R/F of the flywheel housing to facilitate a quick unlocking of a stuck starter bendix, with just a quick pry with a medium screwdriver. I wish I remembered the EXACT location for that hole. It was a Godsend, when you had NO help to push the car when the starter stuck, or if the car was parked where you couldn't push it, or in the middle of a MUDDY road! This trick was shown to him by his old buddy, Bill Ogan, our small town Ford Dealer in Valliant, Oklahoma! Bill W.
__________________
"THE ASSISTANT GURU OF STUFF" |
|
08-29-2013, 10:21 AM | #116 | |
Senior Member
Join Date: May 2010
Location: Portland, Oregon
Posts: 5,920
|
Re: Model A motor froze-up
Quote:
__________________
Ray Horton, Portland, OR As you go through life, keep your eye on the donut, not the hole. |
|
08-30-2013, 01:30 PM | #117 |
Junior Member
Join Date: Feb 2013
Posts: 10
|
Re: Model A motor froze-up
I used a combo of mystery oil and wd40.I put it in the cyls,let it sit adding more for a few days. Then tried to hand turn it.Some times it works on the first try.Most of the it takes a while.I could only spin it a fraction of turn.After a couple days I filled it up again.This time it moved a bit more.I repeated this until it could be spun a complete turn.If you get that far and try to start it beware it will smoke out your neighbors.
|
08-30-2013, 04:18 PM | #118 |
Junior Member
Join Date: Jan 2011
Location: Port Orchard, WA
Posts: 12
|
Re: Model A motor froze-up
I had roughly the same problem. I used the 50/50 mix of ATF and acetone as well. be sure to get some on the valve seats, and into the piston when you put it down the spark plug hole. I let mine sit for a few days, then lifted *one* rear tire off the ground, put the tranny in 3rd, made sure the plugs were out, and started working the tire backwards and forwards. Eventually I saw the fan blade start to move, and now she is running great. Don't give up!
|
08-30-2013, 07:55 PM | #119 |
Senior Member
Join Date: Apr 2013
Location: Middlesex County, NJ
Posts: 298
|
Re: Model A motor froze-up
I see that there have been over 3500 views of this thread. I'm sure that most are viewing this as I am - as a cliffhanger. Wishing Betsy success, sooner rather than later!
|
08-30-2013, 10:09 PM | #120 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Thank you, to both elfox and Michael, my two most recent comers to my cheering section. Not only have I gone through a gallon of Marvel's Miracle Oil (poured into the 4 spark plug holes) but I am squirting tons (slight exaggeration) of liquid wrench wd40, and blaster on nuts and bolts for further projects of loosening Betsy's insides. The fact that the fan moves for me keeps me squirting, shaking, and rocking Betsy.
I do want to give a line of curiousity: for all the MMO I've poured into the 4 spark plug holes, one shows liquid just below the spark plug hole. The other 3 have no sign of MMO. The one hole with obvious MMO is the second from the left. Is there any significance with one cylinder/piston over another? Why do you think one of the four shows MMO and the others none? I'm curious. I'll eventually take the head off - then I'll see what's in Betsy's belly. I'm beginning to feel like a doctor. Poor Betsy is my patient. Thanks for all of your "get well" wishes. |
08-31-2013, 10:52 AM | #121 |
Senior Member
Join Date: May 2010
Location: So Cal
Posts: 8,794
|
Re: Model A motor froze-up
I'd think the one that is not draining is the one that's stuck.
Bob |
08-31-2013, 06:10 PM | #122 |
Member
Join Date: May 2010
Location: Waterloo, IL
Posts: 81
|
Re: Model A motor froze-up
The one that isn't draining could have both valves closed.
__________________
Doug in Waterloo |
Sponsored Links (Register now to hide all advertisements) |
|
08-31-2013, 06:33 PM | #123 |
Senior Member
Join Date: May 2010
Location: Bucks Co, Pa
Posts: 3,740
|
Re: Model A motor froze-up
That piston is at or near Top Dead Center (TDC) and the others aren't. The cylinders are numbered 1 2 3 4 from Front to back.
Terry |
08-31-2013, 07:08 PM | #124 |
Senior Member
Join Date: May 2010
Location: Stayton, Oregon
Posts: 3,806
|
Re: Model A motor froze-up
If you take the head off, years ago I got a Model T engine to move even after it was sitting outside for years with the head off. With the head off, I used a short piece of 4 x 4, inserted it in the cylinder and tapped on it with a hammer. I also used some of the type of stuff you are using to free it up. Good luck.
__________________
Fred Kroon 1929 Std Coupe 1929 Huckster |
09-01-2013, 11:07 AM | #125 |
Junior Member
Join Date: Aug 2013
Location: Asheville, NC
Posts: 28
|
Re: Model A motor froze-up
I’m new in this forum. I’m working on my first model A 1928 roadster pick up. But this is not my first stuck engine. My advice is keep going with soaking with ATF and acetone. By all means take the head off because even if you loosen up the pistons the valve train can be locked up tight as mind is. As I can see the lifters are rusted as well as the valves on their seats. To help loosen the valves, I have been spraying the sauce on top of the valve face and lightly tapping them with a brass rod (shock and awe) and hammer, I have gotten three loose this way. The lifters you will have to just keep spraying them, I do mind every couple of hours. I also found that my distributer is locked up and by all this rocking you could break the distributer drive, plus the distributer drive was locked up on my engine, “take the head off”
. As everyone in this thread has said take your time, it took me over three weeks of heating and soaking to get one cylinder off a 1970 Kawasaki H1. I’ve read a few times about putting a wood dowel in the spark plug hole and tapping with a hammer, not sure about other old ford engines, but this one the spark plug is on top of the valves, so not sure how you are going to reach the piston. Good luck! |
09-01-2013, 12:45 PM | #126 | |
Senior Member
Join Date: May 2010
Location: Bucks Co, Pa
Posts: 3,740
|
Re: Model A motor froze-up
Sponsored Links (Register now to hide all advertisements)
Terry Quote:
|
|
09-01-2013, 01:37 PM | #127 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Thank you, Triple Mike. I see a lot of value in what you are advising. Like Terry says, "I'm a 72-year-old woman." But, I'm mostly Norwegian so I don't know much about the word "can't."
|
09-02-2013, 04:06 PM | #128 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Need advice: a friend wants to power wash the motor. Is that a good idea?
I can push Betsy outside on a graveled driveway. He wants to blast the Motor( and all) under the hood with a power hose connected to a container of Dawn Dishsoap. If it's an okay thing to do, I'll put the spark plugs back in. I'll admit everything under the hood is coated with oil-dirt. I have been scraping it off as I go along. |
09-02-2013, 04:13 PM | #129 |
Senior Member
Join Date: May 2010
Location: Richland Mi.
Posts: 1,172
|
Re: Model A motor froze-up
I personally would however I'd like to hear what others have to say. If you do, put in the spark plugs, remove the plug wires/straps, put a baggie over the distributor and oil filler cap.
After you get it started there will more oil all over but but you'll start with a fresher start. |
09-02-2013, 04:23 PM | #130 |
BANNED
Join Date: May 2010
Location: Bucks County, PA
Posts: 11,454
|
Re: Model A motor froze-up
i am waiting on midget racer to come to the rescue
|
09-02-2013, 05:25 PM | #131 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
I couldn't be more pleased.
|
09-04-2013, 09:25 AM | #132 |
Senior Member
Join Date: Feb 2011
Location: NNNNNNNNJJJJJJJJJJ
Posts: 6,823
|
Re: Model A motor froze-up
Betsy, I pulled my head today and good thing I did. Everything is locked up-cylinders and valves.
You may have to do the same. Will take about an hour with a decent socket set. Hopefully a local model A club or member can stop by to give you a hand.... |
09-04-2013, 05:53 PM | #133 |
Senior Member
Join Date: May 2010
Location: Bismarck ND
Posts: 1,189
|
Re: Model A motor froze-up
I went to see Betsy today and with the help of a tool of Tom's design, we had the engine turning over in a very short time (great design Tom). We could quickly spin it easily with the crank and dumped a lot of MMO from the spark plug holes. Compression is good so I am comfortable that the valves are working good. We also drained about 3/4 tank of skanky gasoline and a pan full of sludgy oil with some MMO in it. The Carb will probably be ok since the gas valve was shut off and the lines were clear. The gas valve was plugged with a molasses like sludge. The very hospitable owners bought me a fine lunch and topped it off with homemade brownies. I think we all had a wonderful day. The owner now wants to try to get it running herself, but reserves the right to keep asking for support and advise. Betsy is a sweet looking survivor pickup that means the world to her owner.
|
09-04-2013, 06:09 PM | #134 |
Senior Member
Join Date: May 2010
Location: Lindenhurst, IL
Posts: 792
|
Re: Model A motor froze-up
You fine sir are a GENTLEMAN! But I really know you just like to tinker!!
|
09-04-2013, 06:26 PM | #135 |
Senior Member
Join Date: Apr 2013
Location: Middlesex County, NJ
Posts: 298
|
Re: Model A motor froze-up
Good job midget racer, and what fine neighbor! I'm glad Betsy had your help and is making progress.
|
09-04-2013, 06:50 PM | #136 |
Junior Member
Join Date: Jun 2010
Posts: 17
|
Re: Model A motor froze-up
I have been lurking in the background watching this thread with much anticipation. Please keep us informed of your progress.
Lance |
09-04-2013, 08:19 PM | #137 |
Senior Member
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
|
Re: Model A motor froze-up
That's great news.
I can't take credit for the tool design though because I saw someone had made one and it was posted on Jim Mason's website. As soon as I saw it I knew I had to use a couple broken starter parts I had laying around, and make my own. |
09-04-2013, 09:27 PM | #138 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Can't thank midgetracer enough for traveling all that way to help Betsy. I gained a new respect for the talent of mechanical work. It was an exciting event just watching an expert take charge of loosening Betsy's motor. What excitement! I couldn't believe my eyes as I watched the crank turn and MMO flying everywhere. I guess the only thing I can equate the feeling to was watching my first grandchild be born. I know "this is not the end, it is the end of the beginning." I am sooooo appreciative of all the concerns, suggestions, and encouragement that brought me to today's charm. I must say, I truly respect a man who steps up to a challenge, and succeeds. You truly are my "rescuer" midgetracer. You have a true gift! God Bless!!! I do realize that my work has just begun, but with your advice and instructions, I'll be able to surge on.
|
09-05-2013, 02:21 AM | #139 |
BANNED
Join Date: May 2010
Location: Bucks County, PA
Posts: 11,454
|
Re: Model A motor froze-up
kudos midget racer....gooood job
|
09-05-2013, 06:33 AM | #140 |
Senior Member
Join Date: May 2010
Location: Richland Mi.
Posts: 1,172
|
Re: Model A motor froze-up
migetracer, thanks for picking up the torch and running with it. You sure made Betsy and her owner happy.
|
09-05-2013, 10:33 AM | #141 |
Senior Member
Join Date: May 2010
Location: Homestead, Fl
Posts: 351
|
Re: Model A motor froze-up
Way to go Midgetracer! It's a fine thing you did for a nice lady, her A and yourself.
|
09-23-2013, 07:51 PM | #142 |
Senior Member
Join Date: May 2010
Location: Richland Mi.
Posts: 1,172
|
Re: Model A motor froze-up
We haven't heard anything in a couple of weeks. Is there any progress being made since the motor seems to be turning over a little?
|
Sponsored Links (Register now to hide all advertisements) |
|
09-23-2013, 09:30 PM | #143 |
Senior Member
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
|
Re: Model A motor froze-up
Funny you should mention that, because I was going to ask the same thing last night, but got sidetracked and forgot.
I was wondering if all the valves are unstuck, so all cylinders have compression. |
09-26-2013, 08:45 PM | #144 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Hi All,
Betsy here. Just a little update. I took some time off - poked myself in the eye cleaning out the lilac bushes. Next time someone offers protective eyewear I'm using it. Now, back to Betsy. Since midgetracer turned the motor over for me, I take delight in turning the crank everytime I come and go from Betsy's garage. I soaked the gas valve in carborator cleaner and reinstaled the gas line. Cleaned out the gas tank with that same type of cleaner. I have water/antifreeze for 37 degrees below, and put fresh oil in the motor. Now then, I'm having a bit of trouble lining up the starter for a remount. I cleaned the starter (on the outside) and put it into place. My problem - can't get the bolts to go in. So, I'm soaking them in carborator cleaner over night. I'll go back to trying again tomorrow. My, that starter is heavy! My husband tried to help as well. Neither of us could get those bolts to enter the hole for it. I'll clean bolts and the mount well tomorrow before trying again. Hey, I'm getting closer to putting in a new battery, new spark plugs, and giving the starter a try. Wish me luck! Betsy |
09-26-2013, 09:30 PM | #145 |
Senior Member
Join Date: Aug 2011
Location: Illinois
Posts: 733
|
Re: Model A motor froze-up
Please make sure you put the starter bolts back into the same spots they came out of. If you use the longer starter bolts in the wrong holes it may jamb into the flywheel. Common mistake often made.
|
09-27-2013, 01:38 AM | #146 |
Senior Member
Join Date: Mar 2013
Location: New Zealand
Posts: 366
|
Re: Model A motor froze-up
Sponsored Links (Register now to hide all advertisements)
|
09-27-2013, 06:45 AM | #147 |
Senior Member
Join Date: May 2010
Location: Richland Mi.
Posts: 1,172
|
Re: Model A motor froze-up
I would suggest running the bolt in and out of their holes without the starter until they do it smoothly. How freely does the motor turn over?
|
09-27-2013, 07:51 AM | #148 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Thanks for that important suggestion, [email protected], I will sure compare the three of them more closely. They look alike, but there must be something different about them. I didn't pay attention to difference in the bolts when they were removed assuming they were alike. Thank you, too, Ross/Kzoo, I will do that too. The crank moves ever so smooth. It has a free flow, but with some resistance. I'll be putting the bolts into the starter today. And, I'll follow these suggestions given. Betsy
|
09-27-2013, 07:52 AM | #149 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Thank you, Mad Mac, for sharing your experience. I'm hoping for no noise (only the sweet sound of Betsy's motor) when I put the starter back in. Wish me luck.
Last edited by BetsyModelA; 09-27-2013 at 07:54 AM. Reason: clarification |
09-27-2013, 09:37 PM | #150 |
Senior Member
Join Date: May 2010
Location: Bismarck ND
Posts: 1,189
|
Re: Model A motor froze-up
The engine turns over real smooth. There is plenty compression for a startup based on the "thumb over the spark plug hole" test. I think a startup is in the near future. Hang in there Betsy Model A.
|
09-28-2013, 03:19 PM | #151 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
My husband and I mounted the starter today. After having soaked the three bolts for 24 hours in carburator cleaner, wiping them clean, doing a practice entrance, seeing which one fit best where, Lynn held the starter in place while I put the first and closest bolt into place, the other two were a piece of cake. I finished that part by connecting the starter foot pedal. Next week, I'm taking my old battery in, have it tested, then replace it with a new one. Next, I'll get some new sparkplugs. Lastly, I'll buy some new gasolene. I'll be driving Betsy before long. Special thanks to midgetracer, my backup expert for Betsy.
|
09-28-2013, 04:17 PM | #152 |
Senior Member
Join Date: May 2010
Location: Portland, Oregon
Posts: 5,920
|
Re: Model A motor froze-up
You want to put the shortest bolt in the hole closest to the block. Turn your engine over with the crank after mounting the starter to make sure that back bolt isn't locking up your flywheel. The engine should turn over with the same resistance as when the starter was not installed.
__________________
Ray Horton, Portland, OR As you go through life, keep your eye on the donut, not the hole. |
09-28-2013, 07:10 PM | #153 |
Senior Member
Join Date: Nov 2011
Location: Dayton Oregon
Posts: 318
|
Re: Model A motor froze-up
I've been lucky----didn't notice the difference. Now I will have to pull the bolts to see.
|
09-28-2013, 07:11 PM | #154 |
Senior Member
Join Date: May 2010
Location: Richland Mi.
Posts: 1,172
|
Re: Model A motor froze-up
|
09-28-2013, 09:05 PM | #155 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Thanks guys. I was forwarned of putting the wrong bolt in the wrong place and hitting the fly wheel. In checking the bolts they look as though they were all the same size. Reluctantly I put them in, and then turned the crank thinking I'd hear a noise, none came. I was much releaved. Perhaps, some Model As have different sizes, then I see there could be a problem if not assembled correctly. Mine was easy! Betsy lucked out!
|
09-28-2013, 09:47 PM | #156 |
Senior Member
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
|
Re: Model A motor froze-up
Unless someone changed the mounting bolts, all 3 should be the same, 3/8" x 1" with a lock washer under each.
|
09-29-2013, 12:29 AM | #157 |
Senior Member
Join Date: May 2010
Location: Portland, Oregon
Posts: 5,920
|
Re: Model A motor froze-up
That's interesting, Tom. I don't remember ever working on an A where one bolt wasn't shorter than the other two. But it could be I wasn't paying close attention until somebody warned me about it.
__________________
Ray Horton, Portland, OR As you go through life, keep your eye on the donut, not the hole. |
09-29-2013, 03:36 PM | #158 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Tom, I concur. The 3 bolts appeared to be the same size with a lock washer.
Upon being warned of different size bolts, After inserting them, I turned the crank, gently, and listened for a possible cklunk or metal on metal, but it didn't happen. Whew! |
10-05-2013, 10:11 AM | #159 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
An update for those interested in Betsy: got new spark plugs, took out the old battery anticpating puttin in the new one. I'm in the process of taking out the current battery box that's rusted through. Ordered a "new" one. The nuts and bolts are rusted tight. Have sprayed penetrating oil on them, leaving them sit a few days, then I'll try a good socket set on them. Wish me luck in the switch. BetsyModelA
|
10-05-2013, 10:47 AM | #160 |
Senior Member
Join Date: May 2010
Location: Fort Bragg,Ca.
Posts: 362
|
Re: Model A motor froze-up
I have dealt with a few 'stuck' old engines and the only thing I would advise is drop the pan and loosen or remove the bearing caps. A couple of the engines would have been good engines if I hadn't just forced it to turn over=the bearings and crank had worked on each other to keep it from turning. If you open it up and the bearings and journals are OK you might have saved a good engine. Than you work on the pistons.
GOOD LUCK! |
10-05-2013, 12:45 PM | #161 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Hi Partridgekelley, nice to have your advice and well-wishes for Betsy. Thank goodness, the motor has become unstuck. An earlier entry referring to midgetracer, who actually came with his socket set and a "Tom's Tool" and unstuck the motor for me. I should probably start a new thread for Betsy to tell of my progress and woes. But, I've just continued on from whence we started. I have received a lot of good info regarding getting "unfroze." The "Tom's Tool" did it especially after a lot of MMO.
Best regards, from Betsy |
10-05-2013, 03:37 PM | #162 |
Senior Member
Join Date: May 2010
Location: Richland Mi.
Posts: 1,172
|
Re: Model A motor froze-up
Yes, if you could start a new thread and maybe title it "Model A motor WAS froze-up"
|
Sponsored Links (Register now to hide all advertisements) |
|
10-05-2013, 09:01 PM | #163 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Thank you, Ross/Kzoo, that sounds like a good idea. I'll try to start a new thread.
BetsyModelA |
10-19-2013, 12:44 PM | #164 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
For the life of me, I can't get a couple of rusted nuts to come off. I need to get them out of the frame that they are in so I can put a different battery box in that spot. All of my penetrating oils/sprays aren't working. Getting very dishearted! I can see that winter is coming on. Wanted to have Betsy running before snow flies. Someone suggested torching them off. I'm afraid of a fire.
|
10-19-2013, 02:41 PM | #165 |
Senior Member
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
|
Re: Model A motor froze-up
You might be able to heat them enough with a small propane torch, but an oxy/acc torch would be the real ticket. Are there any local gear heads that could help?
My dad often used a hammer and chisel to split the nut. Set the chisel blade parallel to the bolt and in the center of the flat, then hammer away until the nut splits. Best to use a chisel guard or chisel holder to avoid smashing your hand, as I did the other day while trying to remove a tire from a rim. |
10-19-2013, 04:04 PM | #166 |
Senior Member
Join Date: May 2010
Location: Richland Mi.
Posts: 1,172
|
Re: Model A motor froze-up
Sponsored Links (Register now to hide all advertisements)
|
10-19-2013, 06:13 PM | #167 |
Senior Member
Join Date: May 2010
Location: Stayton, Oregon
Posts: 3,806
|
Re: Model A motor froze-up
Was also going to suggest this. The Dremel tool has worked well for my in a number of occasions. Harbor Freight, I think, has a copy of one that is reasonable.
__________________
Fred Kroon 1929 Std Coupe 1929 Huckster |
10-19-2013, 06:25 PM | #168 |
Senior Member
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
|
Re: Model A motor froze-up
If you need a Dremel I prefer the real deal rather than something from China. I've purchased a few Dremels on ebay with the box and accessories for $20 to $40.
|
10-19-2013, 06:45 PM | #169 |
Senior Member
Join Date: May 2010
Location: Reseda, Calif.
Posts: 2,190
|
Re: Model A motor froze-up
It might sound crazy but I had a 40 ford once that had very rusty nuts and bolts that had to come off. When I tried to loosen them, they would either strip or sometimes break, which I was happy with. And then I got the idea to just tighten the crap out of them, and sure enough they just broke off. So the rest I just tighten and snapped them all off. Not saying yours would do this, but maybe worth a try. Good luck with it.
|
10-19-2013, 07:02 PM | #170 |
Senior Member
Join Date: May 2010
Location: Richland Mi.
Posts: 1,172
|
Re: Model A motor froze-up
|
10-19-2013, 07:37 PM | #171 |
Senior Member
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
|
Re: Model A motor froze-up
|
10-19-2013, 08:27 PM | #172 |
Senior Member
Join Date: May 2010
Location: Santa Rosa, CA
Posts: 1,282
|
Re: Model A motor froze-up
There is a tool called a nut splitter. It fits over the nut, and you tighten a screw that forces a blade into the side of the nut and splits it. Google nut splitter. Works good.
|
10-19-2013, 08:43 PM | #173 |
Senior Member
Join Date: Sep 2013
Location: Cushing, WI
Posts: 170
|
Re: Model A motor froze-up
I have a nut splitter that works fine the problem is the unruly size of the tool makes it hard in tight spots but does work, Dremel works great also but the disc's are rather spendy. I like the idea of twisting them off and one other way if you have a stick welder you can short the bolt using 75 amps. Before you turn on the welder get a good ground then clamp the hot end to the bolt or nut in question and turn it on and you will have to be the judge as to the time on shut it off and turn the bolt or nut loose, this is the same principle used to un freeze pipes. When all is said and done I like Kroil, squirt it on and hit the bolt or nut hard with a dead blow and wait a day.
I used to play with tractors and found the best way to un stick a motor is to fill the cyl with brake fluid mixed with kero, take an Oak 4x4 and grind it round put it in a cyl and at the same time use a large iron bar with a socket on the crank with a couple friends putting constant pressure on it while you move the log from one cyl to the next, have yet to bend a rod or crack a piston. |
10-19-2013, 09:25 PM | #174 |
Senior Member
Join Date: May 2010
Location: Homestead, Fl
Posts: 351
|
Re: Model A motor froze-up
Are they spinning or is it you don't have the strength to turn them. (No disrespect ma'am) They're just nuts and bolts. Do as others have said and tighten them til they break off. You should be using at least one socket wrench for the leverage end. You may have to use a pipe over the handle to get more leverage--longer the better. Replacement nuts/bolts can be had at any hardware store. Wear some gloves because when they break your knuckles might also. lol Hang in there. You'll get it. I hope they're making the replacement battery box better than they used to. Holes didn't line up on mine.
|
10-22-2013, 08:07 AM | #175 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Thank you, one and all, for your interest, excellent suggestions, and encouragment. Once again, my mechanical hero, midgetracer, is coming - quite a distance - to not just remove those stubborn nuts, but also, to start Betsy. The snow is beginning to threaten us here in ND. He is as enthused about getting Betsy started as I am. I'll continue to keep you in-the-know. Thank you again. Betsy
|
10-22-2013, 09:09 AM | #176 |
Senior Member
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
|
Re: Model A motor froze-up
That's good news, as I'm also anxious to hear that it's running.
Don't throw away the old battery frame, as it might be better to use the mounts and uprights with a new bottom. |
10-22-2013, 09:16 PM | #177 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Tom, Good advice. I am keeping all the parts okay. Like Rusty's concern for the holes not lining up right, I'm holding my breathe to see what else can go wrong. Hopefully, my next entry will be full of happy news.
|
10-22-2013, 09:34 PM | #178 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
I apologize, Rusty. I neglected to answer your question about the nut that won't come off. You asked if it spins. Actually, I have two nuts to remove, one 1/2 inch bolt with a 1/2 nut on the underside of the pickup frame. The bolt turns with the attached nut holding steadfast turning with it. I need to remove that one so it is easier to get at the one that has to come off in order to remove the broken battery box. That is a 9/16 nut attached solid to a bolt. It looks like this side of the battery box has a long (about 2 inches long) bolt on top going through the frame of the pickup to about an inch on the underside. I believe if I remove that 9/16 nut, the bolt will come out of its hole, allowing me to remove that side of the battery box. I removed the broken left-front corner part of the old box. This troublesome one is the right-back part. This battery box is not a "box" at all. Rather it has a u shape with four sided metal strips holding the battery in place. This "box" is fastened down at the top of each tip of the u. Wished I had a picture of it. "Worth a thouand words."
|
10-26-2013, 04:17 PM | #179 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
"Betsy is Alive!!!" These are the very words of Betsy's miracle-worker, midgetracer.
Today, is a day I'm marking on the calendar as the day Betsy came back to life. Yes, she poured out billows of smoke as the motor turned over, the starter engaged, and with a flow of gasoline for her life-blood Betsy hummed the sound that only a Model A can give. She sang her song loud and clear so happy to be running again. Just goes to show, we have experts available at all ages, in all walks of life, ready to share their talents and appreciation of the classical auto giving of themselves just for the joy of it. Midgetracer had a few challenges in today's success, but a few hurdles didn't deter his mission. My deepest gratitude in sticking in there with me, and Betsy. May others with similar challenges reap the sweet reward we are enjoying today. I still remember how to work the clutch. |
10-26-2013, 04:25 PM | #180 |
BANNED
Join Date: May 2010
Location: Bucks County, PA
Posts: 11,454
|
Re: Model A motor froze-up
thats fabulous news enjoy that music .
thankyou again midgetracer its people like you that make this hobby great.. job well done |
10-26-2013, 05:12 PM | #181 |
Senior Member
Join Date: May 2010
Location: Richland Mi.
Posts: 1,172
|
Re: Model A motor froze-up
Congratulations to you and a special thanks to midgetracer for sticking with the project to completion/starting. It's people like midgetracer that make this hobby so worth it.
|
10-26-2013, 07:48 PM | #182 |
Senior Member
Join Date: Mar 2011
Location: Riverview, Michigan
Posts: 127
|
Re: Model A motor froze-up
Congrats Betsy
|
Sponsored Links (Register now to hide all advertisements) |
|
10-26-2013, 08:20 PM | #183 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Thank you, Ross/Kzoo, for staying in there for Betsy with your advice and encouragement. I've gained a lot of knowledge about "how to," and much respect for the mechanics' world.
|
10-26-2013, 08:23 PM | #184 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Thank you, SkimmerBob. Can't believe how far Betsy has come just within the past couple months - thanks to midgetracer.
|
10-26-2013, 08:59 PM | #185 |
Senior Member
Join Date: May 2010
Location: Homestead, Fl
Posts: 351
|
Re: Model A motor froze-up
Way to go midgetracer
|
10-27-2013, 07:30 AM | #186 |
Senior Member
Join Date: Apr 2013
Location: Middlesex County, NJ
Posts: 298
|
Re: Model A motor froze-up
Sponsored Links (Register now to hide all advertisements)
Kudos to midgetracer. Seems he earned some angel wings for his Motometer! |
10-28-2013, 03:00 PM | #187 | |
Senior Member
Join Date: Nov 2011
Location: Woodstock, IL
Posts: 290
|
Re: Model A motor froze-up
Quote:
Just came across this today and have read with interest... Glad to hear the operation was a success doctors.
__________________
- bogie '31 (Mostly) Roadster |
|
10-28-2013, 06:43 PM | #188 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Thank you for your comment, bogiediver. Appreciate your addition to this site, especially your encouragment for my "doctors." I've had contact with some of the Very Best!
|
12-02-2013, 08:32 AM | #189 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
For those who have been following Betsy's progress, I am happy to announce that I was able to start, drive and enjoy a ride in Betsy last Saturday. It was a thrill. With the help and suggestions of so many of you, it happened, and how sweet it is! A special thank you to midgetracer and his selfless contribution with mechanical knowhow and encouragement. Now that Betsy runs, I will concentrate on sprucing her up to looking her best. That'll have to wait until spring. Betsy thanks you all.
|
12-02-2013, 10:03 AM | #190 |
Senior Member
Join Date: Dec 2010
Location: FRESNO, CA
Posts: 12,560
|
Re: Model A motor froze-up
Dog here, Well, I'm glad thet thing is FINALLY runnin' Ol' Bill's read this WHOLE thread to me, about 17 or 19??? TIMES ALL 189 POSTS UF IT
Buster T.
__________________
"THE ASSISTANT GURU OF STUFF" |
12-02-2013, 11:54 AM | #191 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Thank you, Dog, for being a faithful, interested reader with me. At 72, I am now finding a new passion. I'd like to learn more about Betsy - electrical, wiring, gaskets, and more. I guess there is no end to what I don't, but need, to know about this "nuts and bolts" marvel. I'm setting Betsy in for a winter rest, will start again in the spring. ND can get rather cold for fixing.
|
12-02-2013, 12:20 PM | #192 |
Senior Member
Join Date: May 2010
Location: Portland, Oregon
Posts: 5,920
|
Re: Model A motor froze-up
I thought I'd seen a picture of this frozen A, but I can't find it. Could you post one, or direct me to where I could see one?
Be sure to turn the engine over a few times this winter to keep it moving (no need to start it, just circulate some oil), and drain the water so it doesn't really freeze up. You'll probably get other theories on winter storage, but this I what I do, and have done for 50 years, whenever I've had to leave a car over the winter. Now I just drive 'em all the time.
__________________
Ray Horton, Portland, OR As you go through life, keep your eye on the donut, not the hole. Last edited by 700rpm; 12-02-2013 at 12:54 PM. |
12-02-2013, 12:49 PM | #193 |
Senior Member
Join Date: May 2010
Location: Richland Mi.
Posts: 1,172
|
Re: Model A motor froze-up
I can't remember if you put anti freeze in it or not but make sure that there is no water in your A. Glad to see the progress that you've made.
|
12-02-2013, 03:43 PM | #194 |
Senior Member
Join Date: Nov 2013
Location: Northern Bucks Co. Pa
Posts: 632
|
Re: Model A motor froze-up
Hi Betsy! I was away for the whole month of Sept and when I got back, my password no longer worked (Go figure) Anyway, I wondered how you were making out. I'm glad to hear that you got it stated (Taa Daa) Now the next job, cleaning all the MMO and other stuff out of there. Don't discard it yet, you'll have a lot more stuff that's stuck and getting all the rusty joints and sliding parts working again. One place you'll probably need freeing up are the end of the linkage rods (3). Drain and replace all fluids. Trans and rear oil are called 600w. Keep posting as you make progress.
Terry |
12-02-2013, 03:53 PM | #195 |
Member
Join Date: Sep 2010
Posts: 93
|
Re: Model A motor froze-up
I have un stuck many engines including Model A's I remove pluggs fill with diesel fuel leave set for a long time checxking making sure it stays full after setting a couple mounths open hood so you can see fan get a couple friends to help you rock car in high gear keep an eye on fan it will brake lose if you are in a hurry remove starter so you can pry up and down on flywheel it will go only a little at a time you change oil and see how it runs
|
12-02-2013, 04:34 PM | #196 | |
Senior Member
Join Date: Dec 2010
Location: FRESNO, CA
Posts: 12,560
|
Re: Model A motor froze-up
Quote:
Seems everybody thinks them "MAGIC" POTIONS will free up anything!! Chief called most penetrants, "PANTHER-PI**" Bill W.
__________________
"THE ASSISTANT GURU OF STUFF" |
|
12-02-2013, 04:58 PM | #197 |
Senior Member
Join Date: May 2010
Location: Richland Mi.
Posts: 1,172
|
Re: Model A motor froze-up
Bill, she doesn't want to wait 30 years for the diesel to work!
Oh, wait, it was stored for 30 years. LOL |
12-02-2013, 05:12 PM | #198 |
Senior Member
Join Date: Dec 2010
Location: FRESNO, CA
Posts: 12,560
|
Re: Model A motor froze-up
DON'T git WISE, Kzoo, Ol' Bill'l drive back there & KNOCK yer "BLOCK" off!! (He jist got his Driver's license re-nued today!!!!! He only missed 1 question, Gregg missed 2) Cain't wait to see his new pic, with LOOONG hair & his scruffy BEARD Buster T.
__________________
"THE ASSISTANT GURU OF STUFF" |
12-02-2013, 06:10 PM | #199 | |
Senior Member
Join Date: Nov 2013
Location: Northern Bucks Co. Pa
Posts: 632
|
Re: Model A motor froze-up
Bill, With all due respect, The diesel would work, b ut.... We/I thought that changing the method in midstream, would be not really effective and messy. Gallons of oil and diesel to be gotten rid of later. It might have been to much for a 72 YO lady to cope with.
Terry Quote:
|
|
12-02-2013, 07:37 PM | #200 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Sorry if I missed your entry, Bill. Often times, when I got a new suggestion I'd run out and try it without responding. My apologies. I soaked the motor with diesel last winter. Then rocked Betsy with a bunch of MMO. What loosed the motor for me was a tool, called Tom's Tool, made out of parts from an old starter used to force the motor to turn. It worked like a charm. Anyway, I see that I need to drain the water out of the radiator. Also, not sure about the oil, should I drain that too? Too much to learn, and so little time. And, worst of all, no warm weather. Snowed 5 inches lately, without the chains I used to have, I'll leave Betsy inside until spring. Someone mentioned to turn the motor over from time to time. I think that would be a good idea. Suppose I need vital fluids in place to do that. Do I sound confused? I'll get it all together one of these days. Thanks for your help - All.
|
12-02-2013, 07:40 PM | #201 |
Senior Member
Join Date: May 2010
Location: Portland, Oregon
Posts: 5,920
|
Re: Model A motor froze-up
Drain the water or add anti-freeze, but I'd recommend the draining. No need to drain the oil, but a good idea to replace it with new fresh oil before storing for the winter. After you do this, turn the engine over a few times to splash the oil around (don't have to start it). Also pour a couple tablespoons down each spark plug hole. Put the plugs back in. Put a note on your windshield reminding yourself that the car has no water in it. It's easy to forget come springtime when you're anxious for your first drive.
__________________
Ray Horton, Portland, OR As you go through life, keep your eye on the donut, not the hole. Last edited by 700rpm; 12-02-2013 at 07:45 PM. |
12-02-2013, 10:30 PM | #202 | |
Senior Member
Join Date: Dec 2010
Location: FRESNO, CA
Posts: 12,560
|
Re: Model A motor froze-up
Quote:
Sometimes, it's good to hear folks response to an idea, like, "Good Idea"---"Bad Idea"---or, "Blah-Blah," might work better?? This is how we learn NEW stuff sometimes. I DON'T know EVERYTHING, either (The dumb DOG is LAFFING, uncontrollably----"O.K, Fido, you sleep in the FLOOR tonite!) I've created a MONSTER Bill W.
__________________
"THE ASSISTANT GURU OF STUFF" |
|
Sponsored Links (Register now to hide all advertisements) |
|
12-03-2013, 08:28 AM | #203 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
700rpm, just a note to encourage you to see a picture of Betsy on her home page of BetsyModelA. This pic was taken last year when she was towed from one location of storage to a closer shed so I could work on her. She no longer needs to be towed!
|
12-03-2013, 08:31 AM | #204 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
I love your humor, Bill. You have a refreshing way of putting things. All my best!
|
12-03-2013, 12:20 PM | #205 |
Member
Join Date: Sep 2010
Posts: 93
|
Re: Model A motor froze-up
Well Bill Like you I have done many engines that were stuck never used anything but diesel and time I had a friend thast used brake fluid and swore by it being better . after I get them running with new oil in them I might run Kroil in carb as it runs to lube valves I have taken pligs out and taped a stuck vale down . You can do it the easy way or the hard way. Later
|
12-13-2013, 08:51 PM | #206 |
Senior Member
Join Date: Sep 2010
Location: warner robins ga 31088
Posts: 494
|
Re: Model A motor froze-up
Sponsored Links (Register now to hide all advertisements)
The good is my head is off the bad is I have tried all of the different things, to no avail. The #4 cyl leaks down over night,so that is encouraging. I have a bar on the fly wheel and all I have done is break a pressure plate bolt,when I hit the bar with a hammer. I'm keeping #4 full so the fluid is going to the pan. Another bad is the eng is out of the car. If I haven't gotten some movement by next w/e I will turn it over, take the pan off and use a liquid on the bottom of the pistons. |
12-14-2013, 12:55 PM | #207 |
Senior Member
Join Date: May 2010
Location: Stayton, Oregon
Posts: 3,806
|
Re: Model A motor froze-up
After treating all cylinders with whatever you use, you may want to take a short piece of 4x4 and after putting it in each cylinder, tap, and I did say tap it lightly. Do this a number of times over a period of time, and you may get them to move. Then again they may not. When I had my engine rebuilt, the rebuilder had to break the pistons to get them out. (sorry about this comment by that may be where you are at)
__________________
Fred Kroon 1929 Std Coupe 1929 Huckster |
12-14-2013, 01:37 PM | #208 |
Senior Member
Join Date: Sep 2010
Location: warner robins ga 31088
Posts: 494
|
Re: Model A motor froze-up
Fred I've tried that. I still think a little more time with the block of wood, and keeping the top of the piston covered with kerosene, lacquer thinner, and trans fluid, something will give. Going to give it another week before I turn the eng upside down.
|
12-14-2013, 07:03 PM | #209 |
Senior Member
Join Date: May 2010
Location: Fort Bragg,Ca.
Posts: 362
|
Re: Model A motor froze-up
All this is good advice. But if you don't drop the pan and the bearing caps ,you could waste a good set of bearings and journals on the crank.
If you can get the pistons free and it does turn over , I'd still check the insides. If a piston /rings stuck the crank could have the same stuff going on. Good Luck Gary |
12-14-2013, 08:19 PM | #210 |
Senior Member
Join Date: Sep 2010
Location: warner robins ga 31088
Posts: 494
|
Re: Model A motor froze-up
PK, that is exactally what will happen. Since the eng is out of the frame it makes it more difficult. I have a gasket set, and will take it apart just to see what is going on.I think by this time next week it will be turning.
|
12-18-2013, 03:48 PM | #211 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
48fordnut, I empathize. I know the frustration of trying everything, and getting nowhere. Do keep us posted as to what works for you - and something will. Patience was the best advice I was given - don't give up. Turning the motor over is sweet success when it happens - and it will. Betsy sends her best.
|
12-19-2013, 10:24 AM | #212 |
Senior Member
Join Date: Sep 2010
Location: warner robins ga 31088
Posts: 494
|
Re: Model A motor froze-up
Morning all,
Well the saga continues. It started with #4 cyl ,with fluid in the tops of all cyl, when I went out and uncovered the eng fluid had leaked down in #4. Well ,I kept on with the light tap with the hammer till, it was #3, then finally #2. Now that #1 is being a bit stubborn. I have a 1 7/16 socket on the ft nut ,but can't get any leverage. Bit cold this am, but will go thru the ritual in a few minuites. Will keep you posted. |
12-19-2013, 11:17 AM | #213 |
Senior Member
Join Date: May 2010
Location: Richland Mi.
Posts: 1,172
|
Re: Model A motor froze-up
We love to hear of your progress!
|
12-24-2013, 11:13 AM | #214 |
Senior Member
Join Date: Sep 2010
Location: warner robins ga 31088
Posts: 494
|
Re: Model A motor froze-up
Merry Christmas to all, and boy did I find a present this am. I am now able to make a 1/4 revolution on the eng. More patience and diesel fuel and it will be a complete turn. Victory.
|
12-24-2013, 11:16 AM | #215 |
Senior Member
Join Date: May 2010
Location: Richland Mi.
Posts: 1,172
|
Re: Model A motor froze-up
Congratulations! Christmas came a little early for you. It should be easy to turn over soon.
|
12-30-2013, 07:08 PM | #216 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Good for you! I know the feeling!
Do keep us in the know as you progress. |
12-30-2013, 10:57 PM | #217 |
Senior Member
Join Date: May 2010
Location: Alabama
Posts: 8,099
|
Re: Model A motor froze-up
Don't forget to use penetrant on the valves and lifters. A stuck valve or lifter will only allow the engine to turn so far. When the cam lobe reaches the stuck lifter it will quit turning. Good luck you are well on the way.
|
12-31-2013, 04:07 PM | #218 |
Senior Member
Join Date: Sep 2010
Location: warner robins ga 31088
Posts: 494
|
Re: Model A motor froze-up
I knew patience would pay off. Today it turns and very smooth. I will be putting it on a stand and removing the pan and all internals.
|
12-31-2013, 05:44 PM | #219 |
Senior Member
Join Date: May 2010
Location: Alabama
Posts: 8,099
|
Re: Model A motor froze-up
About a quart of oil or more remains in the dipper tray after the oil is drained. When you get the engine on the stand, remove the oil pan while the engine is right side up or you will have an oily mess. Just a thought, You probably already know this.
|
01-24-2014, 01:49 PM | #220 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
For as cold as it has been in ND this winter, I am glad I drained the radiator. Should I have drained the oil out as well? I miss working on Betsy, spring is right around the corner! I hope.
|
01-24-2014, 02:14 PM | #221 | |
Senior Member
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
|
Re: Model A motor froze-up
Quote:
It sure made for a short driving season. |
|
01-24-2014, 06:00 PM | #222 |
Senior Member
Join Date: Nov 2013
Location: Northern Bucks Co. Pa
Posts: 632
|
Re: Model A motor froze-up
I'm still working on my coupe. Granted, it's in a garage, but the concrete is like ice and I'm working underneath. Modified and installed a new RH tailinght and the wiring. Then I made a new bracket and installed a new dual master cylinder in place of the single one I had. Today, I bled the brakes and found that my crossover channel is too weak and must be strengthened. It flexes when you step on the brakes hard, can't have that! A model A owner's work is never done! I can work about two hours and that's it! I'm chilled to the bone!
Terry |
Sponsored Links (Register now to hide all advertisements) |
|
01-25-2014, 08:34 AM | #223 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Terry, NJ
Mine are mechanical brakes, so no liquid to be concerned there. My Betsy is sleeping in a shed with the door blocked with a foot of snow in front of it. Spring can't come fast enough to suit me. I'm getting "cabin fever." |
01-25-2014, 11:07 AM | #224 |
Senior Member
Join Date: Sep 2010
Location: warner robins ga 31088
Posts: 494
|
Re: Model A motor froze-up
Good news all .Eng is in machine shop to be cleaned,read pressure washed, honed and valve job. Crank seems to be good, and will be polished.I missed out on the new in box hi comp head ,because of slowness in making a decision. I did get his new leakless water pump, and a Mallory dist. Now on to rings and checking clearanceson the crank.
|
01-25-2014, 01:02 PM | #225 |
Senior Member
Join Date: May 2010
Location: Mansfield, Ohio
Posts: 422
|
Re: Model A motor froze-up
Hi Betsy, I usually go out to the barn once or twice a month during the winter time to check out the car and turn the motor over by hand so it does not sit on one spot to long. Don't drain the oil as it will circulate around the internal parts when you turn it over.
This was a nice thread... I and probably others feel like we know you now. I know midgetracer does. Good luck and hope everything on your Model A works out well for you and your husband. Tom..... |
01-25-2014, 01:37 PM | #226 |
Senior Member
Join Date: Nov 2013
Location: Northern Bucks Co. Pa
Posts: 632
|
Re: Model A motor froze-up
Sponsored Links (Register now to hide all advertisements)
Terry |
01-25-2014, 02:24 PM | #227 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Thanks Tom. Next day above zero, I'll take my scoop shovel and work my way into the shed to turn the crank a time or two. However, without any heat in this cold, I'm sure that anything metal (all) will be stiff and hard to move. I'll try. I took the battery out last fall, storing it in my basement on lathes of wood.
Yeah, Terry, I don't want to change anything from as original as I can stay with. |
01-25-2014, 03:22 PM | #228 |
Senior Member
Join Date: May 2010
Location: Washington Cty., ME or Flagler Cty., FL
Posts: 1,117
|
Re: Model A motor froze-up
I had an engine that was stuck from sitting too long inside. I tried all of the above. I finally got the engine turning this way but you have to be very careful. Have the hood open on one side so that you can see the fan. Take out all the plugs. I towed the car behind my tractor very slowly, barely moving. I pushed in the clutch, shifted into third gear and very slowly let out the clutch until I could hear the clutch starting to rub on the fly wheel, then I hit the starter. The combination of the clutch and the bump from the starter was enough to break it loose. When you see the fan turning, let the clutch out all the way and not before. Good luck. Ed
|
01-25-2014, 03:46 PM | #229 |
Senior Member
Join Date: May 2010
Location: Rhode Island
Posts: 1,868
|
Re: Model A motor froze-up
We started a coupe that sat since 1947 in a barn. The previous owner could not free the stuck engine despite towing it around in gear. We made a 50/50 Acetone-Auto Transmission fluid mix and filled the cylinders. After a few minutes we rocked the car back and forth in high gear with the plugs out until one by one each cylinder freed itself. We did have to replace the timing gear later as the gear was disintegrated. Today the engine runs great with no smoke.
|
01-25-2014, 09:32 PM | #230 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
For Ed and Ron:
I love happy endings. Glad your recipe worked for each of you. Good to pass this along for others to try. |
09-04-2014, 08:27 AM | #231 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Greetings from Betsy.
It has been a long time since Betsy was able to get going again, not with it this year. A big THANK YOU to Midgetracer, Betsy is up and going once more. Having sat all winter without so much as a start or a turnover, she wouldn't fire now this September. Midgetracer found the gas line plugged, got the flow going again, tuned the points, and pressed the starter. It is through Ford Barn I have Betsy home with me again and running. Now, I can tinker with her, and drive her often, which I will do. She needs a face-lift, but that will come slowly, cautiously, and with loving hands. Again, Midgetracer, thank you for sharing your expertise. My true appreciation to Ford Barn. I'll return as needed. |
09-04-2014, 11:18 AM | #232 |
Senior Member
Join Date: May 2010
Location: Portland, Oregon
Posts: 5,920
|
Re: Model A motor froze-up
Glad to hear it. Don't feel like you can only come here if you need help. We like to hear stories of progress and fun too.
__________________
Ray Horton, Portland, OR As you go through life, keep your eye on the donut, not the hole. |
09-04-2014, 01:03 PM | #233 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Thank you, 700rpm. It is good to be back. Felt I needed to share my good fortune with all who were concerned about Betsy last year. I'll keep my entries short and positive in the days to come.
|
09-04-2014, 04:19 PM | #234 |
Senior Member
Join Date: Nov 2013
Location: Northern Bucks Co. Pa
Posts: 632
|
Re: Model A motor froze-up
Persistence overcomes resistance! Works every time!
Terry |
09-04-2014, 06:41 PM | #235 |
Senior Member
Join Date: May 2010
Location: brentwood, ca
Posts: 4,286
|
Re: Model A motor froze-up
kroil is sold by kano labs(post number 8). the atf/acetone is an alternative. Diesael is also good, and I wonder if oven cleaner will loosen rust.
Bob |
09-09-2014, 11:29 AM | #236 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Terry,NJ Curious - looking at your pic, is that a sedan or a pickup?
Brentwood Bob glad you gave hints, I do have rust problems. |
09-09-2014, 12:15 PM | #237 |
Senior Member
Join Date: May 2010
Location: Michigan
Posts: 581
|
Re: Model A motor froze-up
I made the tool that Tom Wesenberg made and used it on my brothers Model A. He used the hand crank to put pressure on the crank and I used the tool that I made. We were able to free up the motor. ( he also had been soaking the cylinders for a couple of days before we tried it.) Afordman31
|
09-14-2014, 10:10 PM | #238 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
The "Tom Wesenberg tool" was a miracle working invention for Betsy. Glad it worked for you Afordman31. Such a relief to see and feel the motor turn over.
|
09-14-2014, 10:13 PM | #239 |
Senior Member
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
|
Re: Model A motor froze-up
I made my tool, but can't take credit for the idea. I saw it pictured on Jim Mason's website years ago, and thought it was a very needed tool.
|
09-17-2014, 09:13 PM | #240 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Appreciate your modesty, Tom Wesenberg. Between Midgetracer and Betsy, we refer to the miracle-working tool as "Tom's Tool."
Betsy is running nicely. Only problem, her muffler fell off. Ha! Didn't know she could backfire like that. Made her stop. I crawled under and shoved the two parts together to get home. Now I need to buy a new muffler. Or, do I? |
09-17-2014, 09:19 PM | #241 |
Senior Member
Join Date: Nov 2010
Location: Fairbanks, Alaska
Posts: 767
|
Re: Model A motor froze-up
[QUOTE=BetsyModelA;
Betsy is running nicely. Only problem, her muffler fell off. Ha! Didn't know she could backfire like that. Made her stop. I crawled under and shoved the two parts together to get home. Now I need to buy a new muffler. Or, do I?[/QUOTE] Not necessarily, as long as the pipe or the side of the muffler didn't split or spit the guts out somewhere you should be fine. Make sure the exhaust flange to manifold line up straight. Darryl in Fairbanks |
09-18-2014, 09:57 PM | #242 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
darrylkmc,
Thanks for your helpful response. I managed to shove the long pipe into the bigger round part (not sure what it is called). Should I be welding the two parts together? I know the two parts will come apart again. Perhaps, I can find some baling wire to hold them together for a more permanent fix. |
Sponsored Links (Register now to hide all advertisements) |
|
09-19-2014, 01:41 PM | #243 | |
Senior Member
Join Date: Nov 2010
Location: Fairbanks, Alaska
Posts: 767
|
Re: Model A motor froze-up
Quote:
Darryl in Fairbanks |
|
09-19-2014, 10:11 PM | #244 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
I'll try the photo. Not real technologically savy, so need to work on it.
|
09-20-2014, 12:16 PM | #245 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
If you go to my homepage you will see two pictures I took of the muffler. I was unable to pull the two apart for a picture. However, in one of the photos you can see not only where it is broken apart, but also a rusted out hole. Suggestions appreciated.
|
09-20-2014, 12:22 PM | #246 |
Senior Member
Join Date: May 2010
Location: Stayton, Oregon
Posts: 3,806
|
Re: Model A motor froze-up
Sponsored Links (Register now to hide all advertisements)
__________________
Fred Kroon 1929 Std Coupe 1929 Huckster |
09-21-2014, 09:10 PM | #247 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Fred K-OR, I was afraid someone would tell me to put on a new one. I'm not surprised. Guess I better start looking. I'll try ebay.
|
09-22-2014, 02:00 PM | #248 |
Senior Member
Join Date: May 2010
Location: North Carolina
Posts: 611
|
Re: Model A motor froze-up
All of the part houses carry them. I think I would make it easier on yourself and just order through them. Then you know you are not getting junk either. If you are in ND then I would probably try Snyder's or Berts. They are a little closer to you and may be less shipping.
|
09-22-2014, 02:25 PM | #249 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
You're right, 31 Tudor, I wasn't thinking of the size and bulk of the object. I have ordered from Snyder's before. Sometimes it was the right part, sometimes not. I hate sending back. I'm not familiar with Berts.
|
09-22-2014, 02:51 PM | #250 |
Senior Member
Join Date: May 2010
Location: Tulsa Oklahoma
Posts: 298
|
Re: Model A motor froze-up
No,No, Go to Berts, Snyders or Brattons, or a vendor of your choice. Then compare with your Ebay find. Always good to support our vendors. How do I find your webpage? Thanks, Russell. (I need to get one also.)
|
09-22-2014, 03:44 PM | #251 |
Senior Member
Join Date: Feb 2014
Location: Florida - 32128
Posts: 416
|
Engine knock problem
Saturday, out for a fun ride (40 -50 miles), I inherited a steady motor knock. When I rev-up to a steady rpm, I get an internal medium knock. Can't be a rod, because it knocks fairly light and steady, but it does knock harder under load - revving it up or on the road, up a grade. Move the spark up to the "start" area and the knock is a little less than real hard and no powere
I need to find an "A" motor mechanic in my area. A couple of Ford Barn partners have sent me a person in Ashville, NC - James Rogers, but I can't locate him. Does anyone know of a good reliable "A" person close by and near Spartanburg - Greenville, South Carolina, to help me out ? |
09-22-2014, 05:50 PM | #252 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Russel, Did you try BetsyModelA?
|
09-22-2014, 06:01 PM | #253 | |
Senior Member
Join Date: May 2010
Location: So Cal
Posts: 8,794
|
Re: Engine knock problem
Quote:
|
|
09-25-2014, 08:53 AM | #254 |
Member
Join Date: Feb 2013
Location: Harvey, ND
Posts: 99
|
Re: Model A motor froze-up
Russell, thanks for introducing me to Bert's. I am finding mufflers - they are spendy! Now, to find one that fits at an afordable price.
|
05-24-2016, 10:06 PM | #255 |
Senior Member
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
|
Re: Model A motor froze-up
Just when you thought things couldn't get any worse...........they actually got better.
Somehow I don't recall seeing the pictures in dishady's reply in #27. The first picture looks like total junk, but the second picture looks like a completely different tranny. BTW, with 255 replies, some 37,000 views, and no pictures, did this thread really happen? |
05-25-2016, 12:51 PM | #256 |
Senior Member
Join Date: Jul 2011
Location: Elko Nevada
Posts: 217
|
Re: Model A motor froze-up
Do yourself a favor and pull the engine, the cost will most likely be a gasket set. Pulling, pounding and twisting are a great way to make a good engine into a bad engine. Rebuilds are very expensive and you will kick yourself if you ruin the engine in an effort to break it loose. After such a long time sitting, you need to pull the oil pan at the very least and clean the dip tray of sludge and or water. It's really not that hard and if the parts are all serviceable, it will go back together without too much trouble and run for many years.
Last edited by Marshall57; 05-25-2016 at 12:52 PM. Reason: wrong word |
05-25-2016, 05:56 PM | #257 |
Senior Member
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
|
Re: Model A motor froze-up
The engine is loose and has been run, but I was hoping to see some pictures.
|
05-25-2016, 06:57 PM | #258 |
Senior Member
Join Date: Mar 2011
Location: Riverview, Michigan
Posts: 127
|
Re: Model A motor froze-up
So is BetsyModelA tearing up the streets of Harvey these days? Does anybody know? I just looked at the pic in her profile, that's a nice looking truck !! Slightly used I'd call it.I'd leave it just the way it is!
Last edited by SkimmerBob; 05-26-2016 at 05:29 PM. Reason: Poor Puncuation :( |
|
|
Sponsored Links (Register now to hide all advertisements) |
|