|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
10-01-2022, 08:16 PM | #1 |
Member
Join Date: Oct 2015
Location: Manitoba, Canada
Posts: 68
|
tank and fender weltting
hi wondering what is the best way to install the weltting around the tank and fenders ?? thanks
|
10-01-2022, 10:19 PM | #2 |
Senior Member
Join Date: Aug 2012
Location: South East Wisconsin
Posts: 1,279
|
Re: tank and fender weltting
Notch out the bolt holes in the welting so that when you install it, the welting will pretty much line up and you will be able to get the mounting bolts through. The gas tanks are the most difficult. Try to slide the tank in from the front with the welting and tank together, mounting holes lined up. Good luck.
|
Sponsored Links (Register now to hide all advertisements) |
|
10-02-2022, 05:57 AM | #3 |
Senior Member
Join Date: Jun 2015
Location: Signal Mtn, TN (SE TN)
Posts: 2,394
|
Re: tank and fender weltting
Not only cut bolt holes…
You will need to cut kerfs in the flat. Maybe 1/2 to 2/3 thru at the curves. Particularly at the tank and cowl. Fender welting goes in pretty well without kerfs until you get to the shield union. Also the spacer under the windshield goes on before the tank goes in..makes it a lot easier when you get the knack of it. |
10-02-2022, 08:45 AM | #4 |
Senior Member
Join Date: Jun 2014
Location: Land of Lincoln
Posts: 3,166
|
Re: tank and fender weltting
I made/installed some pulling tabs on the doubled part of the welting, 6-8 inches apart . The pulling tabs where cloth duct tape. Patient and practice ! practice on the fender welt as it’s much easier!
__________________
Don't force it with a little hammer tap, tap, tap get a bigger hammer tap done |
10-02-2022, 09:22 AM | #5 |
Senior Member
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,515
|
Re: tank and fender weltting
I'm thankful that I have a sewing machine that I can sew on some tabs in key places to help pull the welting into place. Not all installations require this but I can do it in those situations where it is exceedingly difficult. The welt isn't always long enough on the tail part to be able to grasp it well. The original pyroxylin type welt is much easier to install than the vinyl type. It's not as thick in tail and fits much better.
|
10-02-2022, 11:25 AM | #6 |
Senior Member
Join Date: May 2010
Location: So Cal
Posts: 8,809
|
Re: tank and fender weltting
Sponsored Links (Register now to hide all advertisements)
|
10-02-2022, 12:50 PM | #7 | |
Senior Member
Join Date: May 2010
Location: Eastern Tennessee
Posts: 11,556
|
Re: tank and fender weltting
Quote:
As a side-note, ever wonder why what we buy commercially available is so difficult to work with? Maybe it is because it is not made like Ford made it!! . . |
|
10-02-2022, 06:18 PM | #8 |
Senior Member
Join Date: Feb 2019
Location: Erie Pa
Posts: 707
|
Re: tank and fender weltting
Hello , I thought that “Third Gen “ made some weld that was close to the original?
|
10-02-2022, 07:55 PM | #9 |
Member
Join Date: Oct 2015
Location: Manitoba, Canada
Posts: 68
|
Re: tank and fender weltting
thanks guys for all the good feedback
|
10-02-2022, 07:57 PM | #10 |
Member
Join Date: Oct 2015
Location: Manitoba, Canada
Posts: 68
|
Re: tank and fender weltting
thanks everyone for the great and prompt response
|
10-02-2022, 10:19 PM | #11 |
Member
Join Date: Jul 2011
Location: Candlewood Lake, CT.
Posts: 38
|
Re: tank and fender weltting
About 4 years ago, on a road trip to Wisconsin, I stopped by the late Roy Nacewics’s place in Michigan to pick up some quality hardware. He was out of tank welting and he graciously took the time to run a few yards through his sewing machine for me. I believe at the time he was the only one using the original Ford pyroxylin material for cowl tank and fender welting. Since Third Generation has taken over, I assume they would be using the same original material. It does make a difference.
|
10-03-2022, 03:19 PM | #12 |
Senior Member
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,515
|
Re: tank and fender weltting
The source for the early style material that the welt was made from came from a company that made hard cover book covers and bindings. The material is a faux leather and is much thinner than vinyl. I've heard that it getting harder to source but Third Gen would be the folks to ask. I could use aircraft grade linen or cotton and coat it with aircraft dope to fill the weave but it would be smooth finish. It can be painted before or after instalation depending on needs.
|
10-04-2022, 07:35 AM | #13 |
Senior Member
Join Date: Aug 2017
Location: SoCal Desert
Posts: 826
|
Re: tank and fender weltting
Great info guy's.
I'm needing to replace the tank welting as I get water inside from the corners near the windshield when it rains and when I wash the car. I'll do the roof at the same time probably in November. Regards Bill Regards Bill |
Thread Tools | |
Display Modes | |
|
|
Sponsored Links (Register now to hide all advertisements) |
|