Forum: Model A (1928-31)
Yesterday, 11:37 AM
|
Replies: 4
Views: 240
Re: Front and rear Hubs
I'm not sure what your question is. If your 'new' hubs have all 5 studs swedged in place, use them. Don't over torque, 60 lbs is very adequate.
|
Forum: Model A (1928-31)
Yesterday, 11:32 AM
|
Replies: 9
Views: 332
|
Forum: Model A (1928-31)
Yesterday, 11:30 AM
|
Replies: 9
Views: 437
Re: "New Engine" Balancing"
Balancing a 4 cyl. engine does not have to be done as a unit, the crank, rods, flywheel, etc. can al be done separately.
|
Forum: Model A (1928-31)
05-17-2024, 10:37 AM
|
Replies: 15
Views: 629
Re: cam lube
Assembly lube is the best but either is fine for what you are doing.
|
Forum: Model A (1928-31)
05-11-2024, 11:05 AM
|
Replies: 12
Views: 499
Re: Tight crank gear
I always use a steel gear, a good, old, steel gear is better than a new cast iron gear.
|
Forum: Model A (1928-31)
05-10-2024, 11:08 AM
|
Replies: 12
Views: 499
Re: Tight crank gear
Heat the gear with a oxy/acet or blow torch. Heat it quite but not enough to show any color on it. It should then slip on, at least part way, then gently pound it on all the way. I made a driver...
|
Forum: Model A (1928-31)
05-04-2024, 12:45 PM
|
Replies: 6
Views: 900
Re: Not A, But Interesting
Very interesting! Makes me wonder how Ford and Dodge/Plymouth made their tubular axles in the late 30's? Chrysler also made one but it was a 3-piece unit with riveted on ends.
|
Forum: Model A (1928-31)
05-03-2024, 11:26 AM
|
Replies: 29
Views: 1,747
Re: Sticking valves?
I definitely recommend IMO but also think your rings may be worn, because the compression is slow but fine with oil added. Do the MMO first.
|
Forum: Model A (1928-31)
04-29-2024, 11:26 AM
|
Replies: 11
Views: 903
|
Forum: Model A (1928-31)
04-28-2024, 12:13 PM
|
Replies: 11
Views: 903
Re: Winfield Model M updraft carb
The difference between the S and the SR is that the later has an accelerator pump, not needed IMO. Gasket sets are available. Price depends on size, condition and are they complete with air-horn or...
|
Forum: Model A (1928-31)
04-27-2024, 11:36 AM
|
Replies: 7
Views: 950
Re: Side Water Outlet
The diamond is a genuine Ford part but cast by an outside foundry. That mark can be found on many Ford parts.
|
Forum: Model A (1928-31)
04-27-2024, 11:33 AM
|
Replies: 11
Views: 903
Re: Winfield Model M updraft carb
They were only used on T's. They are better than the stock T carb, but IMO a bit small for the Model A. I've run a few Winfield model S on my warmed up Model A, and really like them.
|
Forum: Model A (1928-31)
04-25-2024, 01:12 PM
|
Replies: 26
Views: 2,288
|
Forum: Model A (1928-31)
04-24-2024, 11:22 AM
|
Replies: 26
Views: 2,288
|
Forum: Model A (1928-31)
04-22-2024, 11:43 AM
|
Replies: 1,413
Views: 330,084
|
Forum: Model A (1928-31)
04-21-2024, 12:47 PM
|
Replies: 13
Views: 2,541
|
Forum: Model A (1928-31)
04-18-2024, 11:08 AM
|
Replies: 13
Views: 2,541
|
Forum: Model A (1928-31)
04-17-2024, 11:48 AM
|
Replies: 2
Views: 507
|
Forum: Model A (1928-31)
04-17-2024, 11:46 AM
|
Replies: 13
Views: 2,541
|
Forum: Model A (1928-31)
04-17-2024, 11:45 AM
|
Replies: 7
Views: 761
|
Forum: Model A (1928-31)
04-13-2024, 11:23 AM
|
Replies: 2
Views: 504
|
Forum: Model A (1928-31)
04-13-2024, 11:20 AM
|
Replies: 20
Views: 1,338
|
Forum: Model A (1928-31)
04-13-2024, 11:09 AM
|
Replies: 4
Views: 411
Re: '31 pickup rear fender filler panels
If yours is a late '31, it has narrower fenders and no fill panel. Late 31's have the fuel shut-off on the front side of the firewall, a dropped steering support, not attached to the gas tank, and a...
|
Forum: Late V8 (1954+)
04-12-2024, 11:11 AM
|
Replies: 0
Views: 397
Antique Nationals
Irwindale Raceway has postponed the Antique Nationals until May 26th due to pending rain. The new date is 5-26-24
|
Forum: Early V8 (1932-53)
04-12-2024, 11:10 AM
|
Replies: 1
Views: 229
Antique Nationals
Irwindale Raceway has postponed the Antique Nationals until May 26th due to pending rain. The new date is 5-26-24
|