Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.09 seconds.
Search: Posts Made By: Terry,OH
Forum: Early V8 (1932-53) Today, 06:47 AM
Replies: 15
Views: 582
Posted By Terry,OH
Re: 1935 Coupe help

If you do get the car the V8 club restoration book will be of great importance since it can answer many questions. Check the club web site.
Forum: Early V8 (1932-53) Yesterday, 01:03 PM
Replies: 15
Views: 582
Posted By Terry,OH
Re: 1935 Coupe help

Std with some add ons like road lights front and rear, which are not period correct. Dash waterfall is 36, heater much later. Looks like a nice car! 35 steering wheel has humps about every inch or...
Forum: Early V8 (1932-53) Yesterday, 09:56 AM
Replies: 5
Views: 338
Posted By Terry,OH
Re: W&h dual ignition

Very rare, hard to find the cap and rotor. Your going to need two coils. I would guess many of the early Ford distributor rebuilders could get it set up properly. Make sure it is set up on a...
Forum: Early V8 (1932-53) Yesterday, 09:48 AM
Replies: 13
Views: 518
Posted By Terry,OH
Re: Clutch Release Shaft Bushing tool

Harbor Freight has bushing driver kit which is inexpensive and fits many bushings. It can be used to install or extract. I like to use threaded rod and nuts to press the bushing drivers, instead of...
Forum: Early V8 (1932-53) 03-19-2024, 09:15 AM
Replies: 6
Views: 370
Posted By Terry,OH
Re: Cluster Gear ID

The teeth at the end of the gear hold a thrush washer in place. Gear appears early like 35-36
Forum: Early V8 (1932-53) 03-19-2024, 09:11 AM
Replies: 23
Views: 1,112
Posted By Terry,OH
Re: FlatheadCoupe John McClure

God Bless and keep him.
Forum: Early V8 (1932-53) 03-18-2024, 10:24 AM
Replies: 1
Views: 193
Posted By Terry,OH
34 original steering outer column

What is the diameter of the 34 outer steering column? 1-1/2"?? I am unable to check my car at this time to confirm.

Thank You.
Forum: Early V8 (1932-53) 03-14-2024, 07:35 PM
Replies: 8
Views: 364
Posted By Terry,OH
Re: 36 firewall body tag

Only vehicles with their bodies assembled by another company, beside Ford, were given a body plate.
Forum: Early V8 (1932-53) 03-14-2024, 06:55 PM
Replies: 8
Views: 364
Posted By Terry,OH
Re: 36 firewall body tag

Some of the closed cars bodies were assembled outside Ford. All of the open cars were outside Ford.
Forum: Early V8 (1932-53) 03-14-2024, 10:30 AM
Replies: 8
Views: 364
Posted By Terry,OH
Re: 36 firewall body tag

Did your car have the two small holes for a body plate attachment, if not the body was assembled by Ford and there would be no body plate.
Forum: Early V8 (1932-53) 03-13-2024, 10:20 AM
Replies: 8
Views: 494
Posted By Terry,OH
Re: Head identity

I leave model A parts in a fellows mail box down the road He has an A.
Forum: Early V8 (1932-53) 03-11-2024, 10:08 AM
Replies: 17
Views: 618
Posted By Terry,OH
Re: 37 Deluxe Coupe with a 11" clutch?

Common?? It sometimes happens with an 11" sounds like your good.
Forum: Early V8 (1932-53) 03-10-2024, 11:16 AM
Replies: 16
Views: 711
Posted By Terry,OH
Re: 1951 Ford, runs fine then runs bad.

There are some very good ideas above. Your symptoms appear to indicate a problem when the car gets to running temperature. Typically the ignition condenser and the coil cause these problems. If you...
Forum: Early V8 (1932-53) 03-10-2024, 10:50 AM
Replies: 5
Views: 328
Posted By Terry,OH
Re: dead spot on starter and sticking bendix

There should be no dead spots. Don't bother with the hammer. Remove the starter if the Bendix is sticking and clean and inspect. Don't lube the Bendix with oil it will eventually cause sticking, dry...
Forum: Early V8 (1932-53) 03-10-2024, 10:42 AM
Replies: 17
Views: 618
Posted By Terry,OH
Re: 37 Deluxe Coupe with a 11" clutch?

If this car has been running a 11" clutch look in the front of the transmission bell housing for marks that the pressure plate may be hitting the casting.
Forum: Early V8 (1932-53) 03-09-2024, 10:26 AM
Replies: 17
Views: 618
Posted By Terry,OH
Re: 37 Deluxe Coupe with a 11" clutch?

Have the flywheel redrilled for a 9" clutch plate. Use the best shouldered bolts as possible.
Forum: Early V8 (1932-53) 03-08-2024, 11:06 AM
Replies: 7
Views: 535
Posted By Terry,OH
Re: Roll out knob

Remove the set screw and add some penetrating oil to the hole.
Forum: Early V8 (1932-53) 03-08-2024, 11:04 AM
Replies: 12
Views: 635
Posted By Terry,OH
Re: Speedometer for 46 Ford Car

Add penetrating oil to a small cup and place the drive end of the speedo in the oil, some oil may get into the shaft and loosen. Suggest driving the speedo with an electric drill and then repeat...
Forum: Early V8 (1932-53) 03-08-2024, 10:55 AM
Replies: 6
Views: 378
Posted By Terry,OH
Re: Rumbleseat trick of regreasing a throwout bearing?

Many auto parts stores sell accessory needles for your grease gun, so adding grease through a small hole is easy.
Forum: Early V8 (1932-53) 03-08-2024, 10:42 AM
Replies: 15
Views: 569
Posted By Terry,OH
Re: replacing starter switch on 1933 ford model b

There is no fuse in the starter motor circuit or the ignition circuit. None of the pre war cars from Ford had fuses in these areas.

I guess you must have mis-spoke in your posting #10...
Forum: Early V8 (1932-53) 03-07-2024, 11:52 AM
Replies: 15
Views: 569
Posted By Terry,OH
Re: replacing starter switch on 1933 ford model b

Think you have the two smaller yellow wires on the wrong side of the switch, they should be on the side with the cable to the battery (-) terminal. The second terminal has just one cable to the...
Forum: Early V8 (1932-53) 03-07-2024, 11:38 AM
Replies: 3
Views: 387
Posted By Terry,OH
Re: Column drop/steering box rebuild questions

small amount of dry graphite lube is good.

For 34 the retaining pin for the ignition lock cylinder is a stepped cylinder with one side the diameter of the hole in the lock cylinder and the larger...
Forum: Early V8 (1932-53) 03-03-2024, 10:37 AM
Replies: 5
Views: 303
Posted By Terry,OH
Re: 34 ford coupe seat adjuster/risers

Your first photo shows the flat locking bars and their spring. There are two rods that pull the locking bars and allow the seat to move. The rods are pulled by a rotating handle and bracket under...
Forum: Early V8 (1932-53) 03-01-2024, 09:19 AM
Replies: 15
Views: 569
Posted By Terry,OH
Re: replacing starter switch on 1933 ford model b

Should be no sparks without power.
Forum: Early V8 (1932-53) 02-29-2024, 09:29 PM
Replies: 13
Views: 633
Posted By Terry,OH
Re: 1936 ANTENNA-PLEASE HELP! Where can I find radio antenna for 1936Ford series 68 c

Your car, If original, has the antenna lead in the widdshield post on the LH side of the driver. It should be connected to the soft top wire insert. The original radio connects there. There is...
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 02:34 PM.