Forum: Model A (1928-31)
02-08-2021, 03:41 PM
|
Replies: 12
Views: 1,984
|
Forum: Model A (1928-31)
07-13-2017, 10:31 AM
|
Replies: 18
Views: 3,711
Re: Torque for bolts on valve cover?
Hey Kory,
Welcome to the barn. A lot of good information on this site! When changing out the gasket I usually clean all around where the gasket goes and now is a good time to clean all inside...
|
Forum: Model A (1928-31)
07-07-2017, 10:15 AM
|
Replies: 24
Views: 5,195
|
Forum: Model A (1928-31)
07-07-2017, 10:03 AM
|
Replies: 56
Views: 9,708
Re: Continuing engine problem
Went through this issue with my rebuilt roadster engine. Would over heat unless I kept moving and had to watch when it idled. Luckily never ran it too far when it was getting hot. I suspected the...
|
Forum: Model A (1928-31)
06-21-2017, 01:28 PM
|
Replies: 107
Views: 16,364
|
Forum: Model A (1928-31)
06-21-2017, 09:26 AM
|
Replies: 13
Views: 2,142
|
Forum: Model A (1928-31)
06-21-2017, 09:21 AM
|
Replies: 6
Views: 1,179
|
Forum: Model A (1928-31)
06-19-2017, 09:22 AM
|
Replies: 24
Views: 5,859
Re: Trailering Model A's
Towed our roadster front facing with the top down. Traveling at 100km+can cause a lot of strain on the old tops. Cardboard on the Rad and Windshield is a good idea
|
Forum: Model A (1928-31)
06-14-2017, 10:38 AM
|
Replies: 4
Views: 2,369
Re: Front seal oil leak
How long ago was it rebuilt? I would call the rebuilder and ask him what should be done first before taking things apart. Doing so might void warranty from the rebuilder.
|
Forum: Model A (1928-31)
11-07-2016, 01:11 PM
|
Replies: 21
Views: 5,596
|
Forum: Model A (1928-31)
11-02-2016, 12:39 PM
|
Replies: 17
Views: 3,097
Re: Why didn't it start again?
I had a similar issue 3 months ago. Replaced the amp meter and coil and still had the same issue. Replaced the cut out and she started and ran perfectly the first try.
|
Forum: Model A (1928-31)
10-29-2016, 01:07 PM
|
Replies: 26
Views: 4,368
|
Forum: Model A (1928-31)
10-03-2016, 10:18 AM
|
Replies: 26
Views: 6,113
|
Forum: Model A (1928-31)
09-20-2016, 08:32 PM
|
Replies: 16
Views: 2,768
|
Forum: Model A (1928-31)
08-31-2016, 08:33 AM
|
Replies: 24
Views: 8,233
|
Forum: Model A (1928-31)
08-30-2016, 08:43 AM
|
Replies: 15
Views: 3,099
Re: Carburetor question
Float needs to be adjusted to proper height or get in the habit of using the hand throttle when coming to a stop. Bring it down a notch or two until you have stopped then return it back to the up...
|
Forum: Model A (1928-31)
06-20-2016, 02:07 PM
|
Replies: 9
Views: 2,373
|
Forum: Model A (1928-31)
06-17-2016, 09:30 PM
|
Replies: 7
Views: 2,148
|
Forum: Model A (1928-31)
06-17-2016, 08:50 PM
|
Replies: 7
Views: 2,148
Re: Transmission Main Shaft issue
Thanks Tom, I checked that option. I removed the 2 gears and main shaft all together and just left the main drive gear and cluster gear in the transmission it turns fine with finger tight bolts...
|
Forum: Model A (1928-31)
06-17-2016, 07:33 PM
|
Replies: 7
Views: 2,148
|
Forum: Model A (1928-31)
06-17-2016, 06:48 PM
|
Replies: 7
Views: 2,148
Transmission Main Shaft issue
Need your help again guys! overhauling the roadster transmission and order all new bearings for it. Notice the main drive gear had some pitting and wear on the nose. So I went ahead and ordered a...
|
Forum: Model A (1928-31)
06-15-2016, 12:22 PM
|
Replies: 5
Views: 1,884
|
Forum: Model A (1928-31)
06-15-2016, 08:18 AM
|
Replies: 5
Views: 1,884
Re: Transmission Question
after cleaning it and inspecting it looks like the threads half way down are stripped. I have a 3/8-24 tap that I will chase and try to fix it. Thanks Tom for the dimensions.
|
Forum: Model A (1928-31)
06-14-2016, 10:37 PM
|
Replies: 5
Views: 1,884
Re: Transmission Question
Thanks Ron, I will try that first. I noticed it wasn't seated when disassembling it. Thought maybe the last person just didn't tighten it down enough.
|
Forum: Model A (1928-31)
06-14-2016, 09:15 PM
|
Replies: 5
Views: 1,884
Transmission Question
Hey Guys!
Quick question regarding the transmission main shaft. I'm currently rebuilding my Roadster transmission and have come across a problem I have never experienced. All the gears in the...
|