Forum: Model T (1909-1927)
09-14-2017, 08:49 PM
|
|
Replies: 26
Views: 9,003
Re: Is this a correct horn for my 1923 model T?
I make reproduction Battery Horns for 1922-1927 Model T. The magneto horn started to appear on a few of the 1915 Model T but then was around for the entire production run through 1927 since the...
|
|
Forum: Model T (1909-1927)
06-08-2017, 05:55 PM
|
|
Replies: 8
Views: 9,587
Re: Timing a Model T
Actually not so great of an idea. Most of the problems with getting proper clearance around timer rod is that people don't know that to properly set the timing and Not have it rub against anything...
|
|
Forum: Model T (1909-1927)
06-08-2017, 05:34 PM
|
|
Replies: 6
Views: 1,829
Re: Coil box rebuild
Thanks for the kind words guys. My web site was down for a few weeks so thought I would make the rounds to see if any fires started burning while I was down ha ha.
Best regards.
John Regan
|
|
Forum: Model A (1928-31)
09-01-2014, 09:09 AM
|
|
Replies: 10
Views: 2,686
Re: fuse fuse fuse
www.funprojects.com/products/AFK-1.aspx
You need a sealed fuse holder since the mounting is right where water and dirt can enter the car as you drive or wash the car. The ammeter does not contain...
|
|
Forum: Model T (1909-1927)
08-28-2014, 11:46 PM
|
|
Replies: 9
Views: 11,744
|
|
Forum: Model T (1909-1927)
08-19-2014, 08:03 AM
|
|
Replies: 7
Views: 1,630
Re: top bow photographs needed
It appears the one of the top sockets is missing on the left side of your picture. There should be 3 on each side with wooden bows spanning the distance across the top.
|
|
Forum: Model T (1909-1927)
03-08-2014, 09:56 PM
|
|
Replies: 4
Views: 2,393
|
|
Forum: Model T (1909-1927)
09-18-2013, 10:15 PM
|
|
Replies: 4
Views: 2,262
|
|
Forum: Model T (1909-1927)
08-04-2013, 02:45 PM
|
|
Replies: 3
Views: 2,107
Re: Using 6V original wiper on 12V question
To operate a 6v device you need to get a voltage dropping resistor that drops 6V off so that you have 6V left. If the shop said 1.5 ohms is correct then it would mean that the wiper motor is drawing...
|
|
Forum: Model A (1928-31)
07-31-2013, 06:34 PM
|
|
Replies: 6
Views: 2,400
Re: 6 V Generator Voltage Regulator -- Remedy
You were one of the easiest people to help and you had a problem that typically is hard to prove out especially over the phone. It is rare to find someone who is willing to listen and cooperate and...
|
|
Forum: Early V8
12-05-2012, 10:45 PM
|
|
Replies: 0
Views: 640
Machine Transport - Atlanta to Illinois
I need an automotive Toe in scuff gauge machine transported from Atlanta, GA to St. Charles, IL or nearby. The machine is basically long, narrow, and flat so could easily slip under any car being...
|
|
Forum: Model-A
12-05-2012, 10:44 PM
|
|
Replies: 0
Views: 1,109
Machine Transport - Atlanta to Illinois
I need an automotive Toe in scuff gauge machine transported from Atlanta, GA to St. Charles, IL or nearby. The machine is basically long, narrow, and flat so could easily slip under any car being...
|
|
Forum: Model-T
12-05-2012, 10:42 PM
|
|
Replies: 0
Views: 1,390
Machine Transport - Atlanta to Illinois
I need an automotive Toe in scuff gauge machine transported from Atlanta, GA to St. Charles, IL or nearby. The machine is basically long, narrow, and flat so could easily slip under any car being...
|
